needle valve 中文意思是什麼
needle valve
解釋
【機械工程】針閥。-
Auto parts : fuel injection system ( valve follower, plunger piston and fuel injection needle, etc. ), power train ( gear, rolling bearing etc. ), piston parts ( packing ring, gudgeon pin etc. ), cam shaft parts ( pin, bush, oscillation beam and some hydraulic components etc. ), others ( gate lock, accouterment etc. )
汽車零部件：燃料噴射系統（氣門挺桿） 、柱塞、噴油針等） 、動力傳動系統（齒輪、滾動軸承等） 、活塞部件（活塞環、活塞銷等） 、凸輪軸部件（銷、襯套、搖臂及部分液壓元件等）和其他部件（如門鎖、內飾等） 。 -
Open the needle valve 2 _ turns from the fully closed position
鎖緊主油針到底，放開2圈。 -
Stainless steel corrosion - resistant needle valve
不銹鋼防腐針型閥 -
Bar - stock needle valve
桿控針形閥 -
Needle valve nozzle mv
針閥噴嘴 -
Angle needle valve
彎角針形閥 -
Gate valve, ball valve, butterfly valve, needle valve and cock valve. cast iron valve, cast steel valve, and stainless steel valve etc
閥門鑄鐵、鑄鋼、不銹鋼等系列閘閥、球閥、蝶閥、針閥、旋塞閥 -
The float system includes the float bowl and a float-and-needle valve.
浮子系統包括：浮子室和一個浮子針閥。 -
Float needle valve
浮子針閥 -
The dissertation also does a research on the control strategies of mechanical control parts. the theoretical expression among needle valve throttle area, cam - control valve throttle area and the equivalent throttle area of combining control is given, and the principle of combining control of the two valves is analyzed. the arresting control strategies under various engaging conditions are presented, namely the engaging condition of same overrunning length and same engaging speed but different weight, the engaging condition of same overrunning length and same weight but different speed as well as the engaging condition of same weight and same engaging speed but different overrunning length
研究了機械控制機構的控制策略：從理論上推導出了針閥節流面積、凸輪控制閥節流面積及聯合控制的當量節流面積三者之間的關系表達式；分析了針閥與凸輪閥聯合控制的控制原理和方法；給出了同攔停距離同撞網速度不同重量飛機撞網狀況、同攔停距離相同重量不同撞網速度飛機撞網狀況以及同重量飛機同撞網速度不同攔停距離撞網狀況的攔阻控制策略。 -
Usting needle valve
調節針閥 -
Open needle valve " a " high side and vent needle valve to vent air from bypass hose
開啟針形閥「 a 」高端和排氣針形閥，從旁路軟管排放空氣。 -
The experiments as follows are done : ( 1 ) space of magnetism sense organ and needle valve is measured
本課題進行了以下設計與試驗: （ 1 ）測定磁感噴油器的磁敏元件和挺桿之間的最佳間隙。 -
The contents of the thesis are as follows : ( 1 ) all the contents : magnetism sense fuel injector is designed. needle valve lift signal, rotation speed signal and pressure signal are collected and processed. circuit is designed. programme is programmed. ( 2 ) contents studied : the item is completed
本課題的研究內容有: （ 1 ）本課題所要研究的內容包括:磁感噴油器的設計;針閥升程信號、主軸轉速信號、噴油壓力信號的採集與處理;系統硬體電路的設計;軟體編程等。 -
Valve needle - cylinder connector
閥針-汽缸連接接頭 -
The technical line of the thesis is as follows : formula of quantity of fuel injection is got by studying relation of quantity of fuel injection and needle valve lift, time of fuel injection, rotation speed and pressure, and quantity of fuel injection is displayed
本課題研究的技術路線為:通過研究噴油量與針閥升程、噴油時間、主軸轉速、噴油壓力等的關系，推導出精確的噴油量計算公式，最終由顯示器顯示噴油量。 -
The authors carry out data collection and calculation for fuel injection pressure and needle valve lift signals measured on the fuel pump test bed by using self - developed software. on the basis of experiments, four criteria for analysing fuel injection process are proposed and the comparison of performances between au and nu type fuel outlet valves is made
作者用自行開發的軟體對在油泵試驗臺上測得的噴油壓力、針閥升程信號進行了數據採集和計算，在試驗的基礎上提出了分析噴油過程的四個判據，給出了au型和nu型出油閥的性能比較結果。 -
Consisting of pvc tube, air - balloon, adjusting valve and stainless steel needle
產品由pvc軟管、氣囊，調節閥，不銹鋼針組成。 -
Connect bypass hose between vent needle valve and loosely connect to test cock no. 1
在排氣針形閥上連接旁路軟管，並將其鬆散連接到測試旋塞1號上。 -
Install a needle valve in the control line. if uneven pressure should cause the regulator to pulsate, its action can be stabilized by throttling the valve
在控制管線上安裝一個針形閥。如果不穩定的壓力導致調節閥波動，則這種波動通過對閥門節流將穩定下來。
分享友人