negative circuit 中文意思是什麼
negative circuit
解釋
負電路-
Dds951 series electronic single - phase electric meter is the most advanced static electronic meter in china. the meter designs use large - scale intergated circuit. high reliability step motor, it can the ac single - phase active energv voltage rating : 220v : frequency 50hz, positive and negative two directions and accumulates in one direction. the test singnal is isolated by phototransistor : it also has the function of anti - fraud, and indicates it s operation situation on flash light, so it could be managed very easy
Dds951單相電子電能表，是金雀儀表公司開發的新型電度表。該產品是採用規模專用集成電路，高可靠性步進電機等先進技術製造的國內最新電能試題新產品，用來計量額定電壓為220v ，頻率為50hz的交流單相有功電能，該產品能夠精確計量正負兩方向的有功電能，且以同一個方向累計。 -
By comparing and analyzing the advantages and disadvantages of three kinds of voltage reference circuits, type of current density ratio compensation 、 weak inversion type and type of poly gate work function, a cascode structure of type of current density ratio compensation is chosen to form the core of voltage reference circuit designed in this paper. applying the negative feedback technology, an output buffer and multiply by - 2 - circuits are designed, which improve the current driving capability
然後通過比較和分析電流密度比補償型、弱反型工作型和多晶硅柵功函數差型三種帶隙電壓基準源電路結構的優缺點，確定了電流密度比補償型共源共柵結構作為本設計核心電路結構，運用負反饋技術設計了基準輸出緩沖電路、輸出電壓倍乘電路，改善了核心電路的帶負載能力和電流驅動能力。 -
In effect, a negative resistance is inserted in the circuit so that its total resistance is zero.
實際上，這就是把負電阻接入電路，使電路的總電阻為零。 -
The final control circuit adopts power mosfet as current control device, which uses the principle of negative feedback to adjust and stabilize output current
末級電路採用功率mosfet作電流控制元件，運用負反饋原理穩定輸出電流。 -
This paper describes mainly system functions, measuring methods, circuit design, software program and errors analysis of a new type of measuring instrument. this instrument can measure and monitor electric parameters in single - phase circuits, three - phase ( three - wire or four - wire ) circuits. this system can be applied to electric devices and power plants, transformer substations with harmonic pollution. it can measure current, voltage, power, energy, frequence, power factor etc. it also can detect load quality, phase sequence, alarm, display and print results, as well as detect and dispose negative power
該儀器適用於含有諧波污染情況下的機電設備現場、發電廠、供電局、企業變電所現場，可用來測量電流、電壓、有功功率、無功功率、視在功率、有功電能、無功電能、視在電能以及頻率和功率因數等電參數，並具有負載性質（感性、容性）判別，正、逆相序判別指示功能；超限報警功能；列印記錄功能和負功檢測及處理功能。 -
There are five parts are as follows : in part one, the concept of switching function is introduced first to establish the nonlinear mathematical model of the induction motor variable frequency speed adjustment system which is fed by a sine pulse width modulated ( spwm ) inverter and takes the effect of the main magnetic circuit saturation into consideration, then the low frequency oscillation of the system is simulated according to the model. next, from the view point of energy conversion of the inverter - induction system, a criterion for the low frequency oscillation is proposed to determine whether the system is in low frequency oscillation which is judged by whether the interval of the negative current component of the inverter input current is more than 1 / fc ( fc is the carrier wave frequency of the inverter ) or not
首先引入開關函數概念，建立了正弦脈寬調制（ spwm ）逆變器供電異步電動機，考慮主磁路飽和時的變頻調速系統整體數學模型，模擬系統的低頻振蕩；其次從逆變器-異步電動機系統能量轉換角度出發，提出通過檢測逆變器輸入電流中負電流的間隔時間是否大於1 / f _ c （ f _ c為逆變器載波頻率）來判定系統是否出現低頻振蕩；最後的實驗結果驗證了系統低頻振蕩建模和判據的實用性和正確性。 -
The variable polarity power supply circuit uses two stages full - bridge inverter, the former inverter is regarded as a constant - current source with fast dynamic response, and supplys energy for the second one, and the latter one is to produce variable polarity current excellently, and low - frequency pulse current by variable polarity power supply is used to reduce input energy and control the shape of weld bead while welding. a series of high - frequency pulse current is superposed on direct - current - electrode - negative ( dcen ) current through the high - frequency pulse power supply, which is used to compress the arc and improve process of crystallization
其中變極性電源採用二次全橋逆變結構，一次逆變提供快速的響應速率並給二次逆變提供能量，二次逆變提供良好的變極性性能，使輸出能量最優化，並用其低頻電流特性減小電弧線能量，控制焊縫成形;高頻脈沖電源提供的高頻電流疊加在反極性電流dcen上，利用電流的高頻特性壓縮電弧，改善焊縫金屬結晶過程。 -
Remember the following words and expressions : e. g. multimeter ； circuit ， current ； voltage ； resistance ； digital multimeter ； analogue multimeter ； analogue multimeter scales ； zero adjustment control ； zero adjustment control for resistance ranges ； measurement ranges switch ； transistor test socket ； meter probe ； positive terminal ； negative terminal ； anode ； cathode ； red lead ； black lead ； power supply ； connect in parallel ； connect in series
記住萬用表、電路、電流、電壓、電阻、數字萬用表、模擬萬用表、表頭、機械零位調整器、歐姆零位調整器、量程選擇開關、晶體管插孔、表棒、正接線端、負接線端、陽極、陰極、紅導線、黑導線、電源、並聯、串聯等常用英文單詞，並逐步掌握。 -
Based on the analysis about the test requirements and the saturated magnetization of the armor plate, the excitation magnetic circuit satisfying the testing condition and a validation system are designed. because the geometric, of the magnetic leakage at the direction of the normal of the roundness fault has the feature of two peaks : a positive and a negative, using the linear regression and the software matlab, two regression equation are proposed : one is about the peak value of the magnetic leakage and the diameter and depth of the roundness fault ; the other is the distance between the two peaks and the diameter of the roundness fault. the result of the validation system proves that the two equations are valid, and an applied method using for quantificationally inspecting the roundness faults is proposed according to the two equations
根據實驗要求，通過對鋼板達到飽和磁化的必要性進行的分析，設計了符合試驗條件的勵磁磁路，並設計了一套實驗驗證系統；根據圓形缺陷法線分量漏磁場幾何圖形正負雙峰值的特點，採用線性回歸擬合的原理和matlab軟體及其統計工具箱中的相關函數，給出了圓形缺陷漏磁場幾何圖形的峰峰值與圓形缺陷的直徑和深度以及峰峰值間距與圓形缺陷直徑的兩個回歸擬合方程，並通過實驗驗證系統驗證了擬合方程的正確性，利用這兩個簡單實用的擬合方程，提出了一種工程定量檢測圓形缺陷的應用方案。 -
Subsequently, we can get the chip s - parameter by adding the negative equipment circuit of the parasitic parameters in the s - parameter model of packaged device
之後，在有管殼封裝器件的s參數模型中，加上負的寄生參量的等效電路，即可得到管芯的s參數。 -
To accept the current signal from high negative voltage circuit, the analog ground is raised to a certain positive voltage, which makes it possible for the signal amplitude to be compressed at the same time of its polarity reversion. a pi control program special for laser gyro current control is brought forward according to the conventional pid control method, in which the control signal is figured out corresponding to the difference between the sample and the reference value by turn of proportion - short step integral - long step integral. and at the end of this paper, a comparison of system performance on different conditions is made and the key elements influencing system performance are educed
利用集成a / d 、 d / a轉換器的新型晶元aduc824 ，實現了電流（電壓）采樣?數據處理?電流控制的閉環控制結構；地電位的抬升解決了a / d轉換器對負高壓迴路電流采樣時的輸入范圍匹配問題；控制信號反相的同時進行幅度壓縮，使得輸出調整電壓的解析度提高；根據常規的比例?積分?微分（ pid ）調節模型，針對陀螺系統的特性，給出了一種可以滿足系統要求、據采樣值偏差大小進行的比例?大步長積分?小步長積分、分層次比例?積分演算法；不同條件下系統穩流性能的對比、分析在論文最後給出，並據此找出了決定該系統穩流精度的關鍵因素，提出了系統的改進意見。 -
By constructing the necessary condition and sufficient condition for feedback to exist in a circuit, can derive the methods of short circuit or open circuit for the load or the signal source resistance respectively of the feedback network, to analyze the configurations of the negative feedback circuits
通過構建電路存在反饋的必要條件和充要條件，可引出令反饋電路的負載和信號源內阻分別短路或開路的方法，用於分析負反饋電路的組態。 -
The actual negative feedback amplifying circuit doesn ' t form a closed - loop only from the basic amplifying circuit and the feedback network, but forms the multi - loop system ( multi - loop negative feedback circuit ) from several basic amplifying circuits and several feedback networks
摘要實際的負反饋放大電路，並非都是由基本放大電路和反饋網路構成一個閉環系統< 1 > ，還有由多個基本放大電路和多個反饋網路構成的多環系統（多環負反饋電路） < 2 > 。 -
According to the different sample electricity from the output loop of the circuit by the feedback network and the different ways of connection between the input loop of the circuit and the feedback network, can divide the configurations of alternate negative feedback circuit into four kinds : voltage series, voltage parallel, current series and current parallel
摘要根據反饋網路從電路輸出迴路的不同取樣電量和在輸入迴路的不同連接方式，可把交流負反饋電路的組態分為電壓串聯、電壓並聯、電流串聯和電流並聯4種。 -
The following is the main works and conclusions of this thesis. the novel upfc needs high power rate because it is generally used in high voltage transmission lines. after studied high - power converters and the literatures of upfc, the main circuit topology of novel upfc base on diode - clamping multilevel inverter is presented and the principle of using novel upfc to eliminate zero sequence and negative sequence currents is analyzed
本文所做的主要工作及得出的主要結論如下：由於upfc一般用於高壓輸電線，其功率等級要求很高，在綜合研究大功率變換器和upfc現有文獻的基礎上，提出了基於二極體箝位多電平變換器的新型upfc的主電路拓撲，分析了用其來濾出高壓輸電線非全相運行時所產生的零序和負序電流的原理。 -
The fitness of four negative electrode materials such as al, fe, zn, cd, and of six membranes materials : microfiber glass mat separator, polyethylene, polypropylene, polyvinyl chloride, vinylon, soapnated cellulose acetate, and of four current collects : carbon fiber ; nickel foam ; nickel foam sthongthened by iron wire net, punched silver grid in the super - iron alkaline batteries was comparatively studied. the influence of two storaged method ( with and without electrolyte ) and two impurities ( zno, fe ( oh ) 3 ) to the experiment cell ' s self - discharge nature was also comparatively studied. at last, the nature of discharge. structure and electrochemistry of experimental cell with k2feo4 as cathode active material prepared by three different methods : high temperature reaction, hypochlorite oxidizing and electrolysis, was comparative ly studied. we can conclude : i ) the open - circuit potential and the flat of work potential and the percent of capacity of k2feo4 till 1. 0v during the discharge at constant load of experimental cells decreased by the order of al / k2feo4, zn / k2feo4, cd / k2feo4, fe / k2feo4. as for the nature of charge - discharge cycle, cd / k2feo4 fe / k2feo4 zn / k2feo4. in water solute electrolyte, although al / k2feo4 can n ' t be used as storage battery, it have great potential as primary cell or storage cell from the aspect of its discharge capacity. discharge power
採用組裝實驗電池、 x -射線衍射（ xrd ）和循環伏安（ cv ）的方法，從實驗電池的放電特性、充放電循環特性、自放電特性，不同高鐵酸鹽的結構特性和電化學特性幾個方面，對4種金屬負極材料（ al 、 fe 、 zn 、 cd ） 、 6種隔膜材料（復合玻璃纖維、幅射接枝聚乙烯、改性聚丙烯、聚氯乙烯、維尼綸無紡布、皂化再生纖維素） 、 4種集流體材料（泡沫鎳、以鐵網為加強層的泡沫鎳、切拉銀網、炭纖維編織網）在堿性高鐵電池中的適用性進行了比較研究；對2種雜質組分（ zno 、 fe （ oh ） _ 3 ）和2類不同貯存方式（干、濕）對實驗電池自放電特性的影響進行了比較研究；對3種方法（高溫固相反應、次氯酸鹽氧化、直流電解）所制k _ 2feo _ 4的實驗電池的放電特性、結構特性和電化學性能進行了比較研究。 -
In this circuit, we use many kinds of negative feedback to modify the ou tput wave, which can decrease the distortion. and we use the high - voltage and high frequency capacitance efficiency, which can decrease the disturbance of output signal of variable frequency source for the test of part discharge
採用了多種負反饋迴路修正輸出波形，使得輸出電壓波形的失真度很小；並且在電路中有效利用高壓高頻電容，減小了變頻電源輸出的電壓對局部放電試驗時的干擾。 -
Basde on further, analysis of formula d = 1 - af, this paper points out the conflict when using instantaneous limit and jadging positire and negative feedbavk byusing the depth of peedbavk, range of middle freguency of pnegative feedback amp circuit can also appear self - conflitct
摘要通過對公式d = 1 - af的進一步分析，指出用瞬時極性法與用反饋深度判定正負反饋時所出現的矛盾，說明負反饋放大電路的中頻段也會出現自激的情況。 -
In this paper, the application of ewb simulation technology in electronic circuit course design is introduced, using negative feedback amplifier as a example
摘要以「負反饋放大器」課程設計為例，分析了ewb模擬技術在電子線路課程設計教學中應用的實施過程。 -
The led lights red when contacting a positive circuit. the led lights green when contacting a negative circuit
當探針接觸及負極-時，綠色led燈會亮起
分享友人