nozzle body 中文意思是什麼
nozzle body
解釋
噴管外錐體-
14. no warranty will be delivered to such consumables as nozzle, cylinder body caulking, washer, seal ring, o - ring, motor brush, capacitor, bulb, fuse, battery, fan, belt, paper filter element, glass sheet, fuel and lubricant
下列消耗品：噴油嘴缸體堵頭，墊片密封圈o型圈電機刷電容燈泡保險熔絲電池風扇皮帶紙濾蕊玻璃板燃油和潤滑劑。 -
In this thesis, based on pershing ii surface to surface missile, a new kind of ballistic missile was designed with an additional rocket engine, which can be ignited twice. firstly, aerodynamic computational models of missile body and warhead which reentry with supersonic are built according to the task requirements ; secondly, the propulsion system model of missile is built whose first two stages are solid rocket engines and the third stage is liquid - solid combined rocket engine. the nozzle and the shape of the engine are designed to meet the needs of the populsion project ; thirdly, the trajectory model of the mass point is built and a wavy trajectory is designed & optimized ; finally, the ability of a missile ' s breaking through defence is analyzed
以美國潘興導彈為原型，增加可兩次點火的末級發動機，改裝成具有跳躍能力的地地彈道導彈；首先，根據任務需求，建立了導彈的氣動模型，並建立了彈頭再入時高超聲速氣動模型；其次，建立了導彈推進系統模型，前兩級採用了固體火箭發動機，第三級採用了固?液組合火箭發動機，並在總體方案要求下，對發動機噴管和外形進行了設計；第三部分，建立了導彈質點彈道模型，設計了一條跳躍式彈道，並對跳躍式彈道進行了優化設計；最後，對導彈進行了突防能力分析，從分析的結果可以看出，跳躍式彈道的突防能力比常規的拋物線彈道要強。 -
In arbitrary curvilinear coordinate systems, three dimensional turbulent combustion flow fields of the three kinds of turbofan engine afterburner with the longitudinal heat shield 、 outer cold flow and the jet nozzle are simulated. the three - dimensional body - fitted grids are generated by an elliptical grid generation procedure and zone method
本文在任意曲線坐標系統下對三種帶有縱向隔熱屏、外冷卻通道和尾噴管的渦扇發動機加力燃燒室的三維紊流燃燒流場進行數值模擬。 -
The effects of such elements as primary flow total pressure, flow rate, degree of fuel rich, nozzle structure, flying speed and secondary combustion on ejecting mode performance were researched. it was found that thrust augmentation can be achieved on the condition that the flying mach number is above 0. 7. to deeply analyze thrust augmentation mechanism in low speed range, the research was further continued by changing secondary combustion organization and aft - body configuration
研究了一次流總壓、流量、富燃程度、噴管結構、二次流來流速度、二次燃燒組織對引射模態性能的影響，發現實驗樣機構型在0 . 7ma以上的飛行條件下可以獲得推力增強，而在0 . 7ma以下無推力增強。 -
Engineering drawing system can draw two dimension curve graphs, main detail drawing and assembly drawing. the curve of internal trajectory and dynamic simulation of particle external trajectory. the detail drawing includes the graph of chamber, grain design, connection body, nozzle, some standard part
工程繪圖可以繪制二維曲線圖和零部件圖，其中二維曲線包括有內彈道壓（推）力?時間曲線、質點外彈道動態模擬曲線；零部件圖包括有標準螺栓與螺紋孔、燃燒室結構圖、裝藥設計截面圖、連接底結構圖、噴管結構圖及火箭發動機總體裝配圖。
分享友人