oil coolant 中文意思是什麼
oil coolant
解釋
冷卻油-
The electronic module of new digital caliper takes fully enclosed design, frees from the erosion of water, coolant and oil, so the new digital caliper can be used under many kinds of bad working condition
在廣州市政府的資助和廣科技局的支持下，公司相繼研發出多項成果，並成功應用到數顯量具的生產中，使傳統數顯量具的可靠性準確性得到進一步提高。 -
The experiments of high speed milling of titanium alloy were conducted under different cooling and lubricating modes, i. e. dry milling, flood coolant, oil mist with nitrogen gas, cryogenic nitrogen gas jet, and cryogenic nitrogen gas jet with minimal quantities of lubricant
在干銑削、澆注切削液、常溫氮氣油霧、低溫氮氣射流和低溫氮氣射流結合微量潤滑等冷卻潤滑條件下進行了鈦合金的高速銑削對比試驗。 -
The cooling system for engine adopted hydraulic drive and control technology to control the speed of the fan : the chip adjust the control - current of the proportional value, which used in the engine cooling system, to control the speed of the fan. and the size of the control - current is according to the coolant temperature, coolant temperature change rate and target temperature. as for as the hydraulic cooling system we used a motor to drive and control the fan ’ s work or stop according to the temperature of the hydraulic oil
該系統的特點及其實現的功能為:電液混合驅動方式改變了工程機械冷卻裝置驅動方式單一的缺點，發動機冷卻系統採用了電液比例技術控制風扇轉速;單片機可以根據冷卻液溫度、冷卻液溫度變化率和目標冷卻液溫度調節液壓驅動系統中電液比例閥的控制電流，進而控制液壓油的流量，即可以實現冷卻風扇轉速的連續調節;液壓油冷卻系統採用了電動機驅動，然後由單片機根據液壓油的溫度控制電動機的起動和停止。 -
Abstract : according to the working conditions of cutting lubricating coolant used in stone processing, we developed a specialized emulsifying oil for stone processing cooloant, and estabhshed the corresponding standard
文摘:根據石材加工使用切削潤滑冷卻液的工作要求，開發研製專用的石材加工冷卻液乳化油，應制定出相應的產品標準。 -
Large sized coolant cleaner ( oil separator ) with a flow rate of 1200 l / h for application in aluminium hot rolling process with coolant tanks of up to 300 ’ 000 litres
每小時1200公升大尺寸的冷卻洗滌器適用在冷卻槽大於300 ， 000公升的熱鋁滾動加工冷卻洗滌器 -
After the evacuations of base oil, emulsifier and anti - wear additives, it proves that the result of usage of emulsifying oil for stone processing coolant in the factory is satisfied
通過對基礎油、乳化劑、抗磨劑等評選，研製出的石材加工冷卻液乳化油在石材加工廠試用取得滿意的結果。 -
Analysis of the test results of the rear - installed cooling system revealed that the overheat problem resulted from the measured cooling air temperature being higher and the coolant flow and transmission oil flow being smaller than the correct design value, and that the wrong location of the hydraulic oil cooler cannot completely meet the need of the cooling system
通過對測試數據進行分析，確定了系統過熱的原因，即系統中測試獲取的冷卻風的溫度比設計值高，冷卻水和傳動油的體積流量比設計值小，而且液壓油散熱器布置位置錯誤。 -
Quality standard for in - service sealing oil of generator using hydrogen as a coolant
運行中氫冷發電機用密封油質量標準
分享友人