orbit curve 中文意思是什麼
orbit curve
解釋
軌道表面上的-
2 ) applied hertz theory and the force between roller ( or ball ) and orbit, the equation groups for calculating equal contact stress curve are listed. the answer of the equation groups is calculated by utilizing the software matlab. the result of the simulation to this answer proved that the answer is reasonable and the design rule also be discussed from the analysis result
（ 2 ）應用赫茲接觸理論和所求得的軌道與滾動體之間的正壓力，分別列出以球和滾子作滾動體的等接觸應力軌道曲線方程組，利用matlab求解方程組，並對求解結果進行模擬分析，論證了所求的結果在理論上的合理性，歸納出設計這種液壓馬達的注意事項。 -
3 ) based on the analysis result of equal contact stress curve and the theory of elasto - hydrodynamic lubrication, the expression of the oil film thickness between roller ( or ball ) and orbit are calculated. the simulation result proved that the thickness of oil film is enough for bearing and lubricating
（ 3 ）基於等接觸應力曲線的求解結果和彈性流體動力潤滑理論，求得滾動體和軌道曲線間的油膜厚度表達式，並通過模擬分析論證了馬達正常工作時這種油膜能滿足承載能力和潤滑的需要。 -
To directly estimate the life of this kind of motor, and to design a orbit curve with the longest life at same condition, this paper gives theoretic research of the equal contact stress inner curve of radial piston motor. the research is divided into four parts : 1 ) taken all forces the piston endured into consideration when radial piston motor working, the force between roller ( or ball ) and orbit is deduced. the simple style of the press expression can be confirmed by ignoring minor influence factors after analysis all factors that will influence this press
靜壓傳動技術在各類工程機械中得到廣泛的應用，對作為其核心部件的徑向柱塞式低速大扭矩液壓馬達的研究顯得十分重要，為了能直接對這種馬達進行壽命估計，並能在相同工況下求得壽命最長的軌道曲線，本文從設計等接觸應力內曲線的角度對這類馬達作探討性的研究，主要從以下四個方面進行： （ 1 ）綜合考慮徑向柱塞式液壓馬達工作時的各種主要受力狀況，對柱塞組件進行受力分析，並通過模擬分析影響軌道和滾動體間正壓力的各個因素，得到正壓力的簡化表達式。 -
The theories of multi member function ' s extremity value, hooke jeeves mode searching method solving wholly complex problem of extremity value and uniformity design method, one new and efficient method to choose test point, are applied to establish the two - dimension oil well orbit optimized model. the shortest length of oil well orbit curve is regarded as this model ' s object and all kinds of effecting parameters are analyzed
通過引入多元函數極值理論、求解復雜極值問題的hookejeeves模式搜索法及一種較為新穎和高效的試驗點選擇方法：均勻設計法，建立以最短油井軌跡曲線長為目標的二維油井軌道優化設計模型，並對影響井軌跡曲線的參數進行了較為詳細的分析。 -
An orbit curve identification method based on characteristic is presented
提出一種基於特徵的軌跡曲線識別方法。 -
3. when = 0, we give the curve of the multiple orbit bifurcation in the parameter plane (, l ). and we prove that the bifurcation of multiple loop is a double orbit bifurcation and the curve is convex
3 、當= 0時，在參數平面上（ ， l ）給出重閉軌分支曲線並證明該重閉軌分支為二重閉軌分支，且該分支曲線是上凸的。
分享友人