output control line 中文意思是什麼
output control line
解釋
輸出控制線-
Ocl output control line
輸出控制線 -
The product is suitable for double straight line smoothing of grinding flat glass. coarse grinding, fine grinding, and polishing can be done at one time. adopt plc control system, which sets processing parameters via interface, and finishes processing at one time, ti has stable bottom structureprecise and smooth transmission system, the transmission belt drive adopts strong power and tran - sfrequency motor to control speed, constant power, constant rule, output and advanced equipment to control, completed product has high polishing level, which is an ideal option assistant processed equipment of processing delicacy glass and furniture glass factory
本產品適用於磨削平板玻璃是雙直線平邊，粗磨精磨拋光一次完成採用plc控制系統通過界面設定加工參數次完成加工，具有穩重扎實的底座結構，精確流暢的傳動系繞，傳送皮帶驅動採用功率變頻電機調速控制，恆功率恆扭矩輸出和高配置的控製成品拋光亮度高是加工精品玻璃和傢具玻璃廠家使用的最佳輔助加工設備。 -
Compared with the pid controller in the real - time experiment and off - line simulation, it shows that not only the output of system is small overshoot and rapid respond time when the logical rule controller acts, but also its control strategy is easy to be performed
與傳統的pid控制器作用相比，離線模擬和在線實驗表明，邏輯規則控制器作用下的系統輸出不僅超調量小，響應時間快，而且控制策略簡單易行。 -
The function of the software use pc - computer to dispose the output signal which is produced by the device as following steps : ( 1 ) to input data by parallel interface ( 2 ) to record and form a file ( 3 ) to demonstrate results step by step ( 4 ) the results could be compiled ( 5 ) it can synthesis in the permitted error scope, substituted original dot for line or arc, finally we could get a graph that is described by some simply curve. ( 6 ) to convert these graph into a program, which used in the cutting process of numerical control. ( 7 ) the software also includes some protective methods
而系統處理軟體的作用是：利用pc兼容機，將上述裝置的輸出信號（ 1 ）通過并行口輸入（ 2 ）記錄成文件（ 3 ）逐點顯示出來（ 4 ）可人工進行化簡，編輯（刪、改點）等（ 5 ）可在給定誤差范圍內進行人工擬合，用直線和圓弧取代原來的點，得到一個與原圖形的誤差在規定范圍內，又消除跟蹤過程中因受到各種干擾而造成的缺陷，由盡可能少而簡捷的數學曲線描述的圖形（ 6 ）把這些圖形轉化成用於編制數控線切割加工程序及autocad能夠識別的文件（主要指dxf格式） （ 7 ）該軟體還有一定的加密措施。 -
Mc closed - loop control method based on dsvm is presented, in which the rms value of output line voltage is taken as feedback and pi regulator is adopted
提出了雙空間矢量調制矩陣變換器的輸出電壓有效值閉環的控制方法，將矩陣變換器輸出線電壓有效值作為反饋值，採用pi調節器實現系統的閉環控制。 -
Intelligent counter digital frequency rotating speed line velocity display control transmit instruments are all adopt used advanced microprocessor for smart control. input is pulsed quantity or contect switch quantity signal, after cpu operation processing, count, rotating speed or line velocity will be clearly intuitional indicated by high brightness led numeral tube, at the same time, these signals can be changed into standard voltage current signal to transmit output. and have the functions of super - limited alarm, standard serial communication function
簡易后備操作器接收從dcs系統或pid調節器給定的模擬量信號，正常控制時，操作器輸入輸出相當于直通的，以實現dcs系統或pid調節器對執行機構的自動控制，當前級dcs系統或pid調節器發生故障時，操作器接收到故障狀態信號，即轉為手動控制狀態，由按鍵控制操作信號的輸出，當故障解除，儀表自動恢復自動狀態。 -
Are all adopt used advanced microprocessor for smart control. input is pulsed quantity or contect switch quantity signal, after cpu operation processing, count, rotating speed or line velocity will be clearly intuitional indicated by high brightness led numeral tube, at the same time, these signals can be changed into standard voltage current signal to transmit output. and have the functions of super - limited alarm, standard serial communication function
接收從dcs系統或pid調節器給定的模擬量信號，正常控制時，操作器輸入輸出相當于直通的，以實現dcs系統或pid調節器對執行機構的自動控制，當前級dcs系統或pid調節器發生故障時，操作器接收到故障狀態信號，即轉為手動控制狀態，由按鍵控制操作信號的輸出，當故障解除，儀表自動恢復自動狀態。 -
The topologies family include single four - quadrant power switch mode, push - pull mode, half - bridge mode, and full - bridge mode circuits. taking full - bridge mode circuit as an example, the operational mode, steady principles, transient voltage feedback control strategy of the converter are investigated. the output characteristic curve, the design for the key circuit parameters and the reference sinusoidal circuit which is synchronous with the signal of n or 1 / n times line voltage frequency are given
該電路拓撲族包括單四象限功率開關式、推挽式、半橋式、全橋式電路，以全橋式電路為例分析研究了這類換器工作模式、穩態原理與電壓瞬時值反饋控制策略，給出了變換器的外特性曲線、關鍵電路參數、與電網電壓n倍頻或n分頻信號同步的基準正弦電路的設計。 -
Before the connectting between moden and other equipments, it works at the cammand mode, the cammand that is send to moden is used to set or manipulate the mode, after the connectting between moden and other equipments, it works at connectting mode, at that time, the cammand send from the computer is send to another computer which will pass the moden and telephone line. the moden control cammand is called " at " cammand, all the control manipulation is realized by sending the ascii character to moden, after the moden received the " at " cammand, it firstly judges the cammand, secondly, it analyses and executes the cammand, finnally, it executes a response by sending back a ascii character, during the deseign of below - computer, we introduce in detail the deseign of system hardware and system software, below - computer system hardware and system software, below - computer is made up of microchip collecting and controlling system, which finish the strobe and water level data collection, display and disposal, deal with the communication with the above - computer, the microchip is the centre of data dealing with, the peripheral equipments are made up of data collecttion module, control cammand input module, display module, execute output module, and long - distance communication module
在moden控制軟體的設計中，詳細敘述了moden正常工作時的幾個重要函數：初始化函數、撥號處理函數、應答處理函數、掛機處理函數，設計並調試了四個函數的通信程序，數據機工作時存在兩種模式，命令模式與連線模式，命令模式是針對功能設置的模式，連線模式是數據傳輸的模式。當數據機未與其他設備連接時，其處于命令模式，這時候下達給數據機的指令是作為數據機本身設置或操作用的；當數據機已經與其他設備連接時，其處于連線模式，所有在此時由計算機送至數據機的信息都將經由電話線傳送到另一部計算機上。專門使用於控制數據機的指令集被稱為「 at指令集」 ，對moden的所有操作（如撥號、應答、掛機等）都可以通過給moden發送ascii字元串來實現， moden在收到at命令后，先對命令進行判斷，接著分析和執行命令緩沖區中的命令，最後以自身的ascii字元對命令作出響應。 -
We discussed the four - legged inverter with space vector modulation ( svm ) to aim at three - phase four - line output ; we introduced the principle of three dimensions svm, and attained the related control scheme. with the illustration of 15kva vscf power inverter, we tested and verified that the inverter system under 3d svm control can realize the three phase four line output and linear voltage regulating
針對三相四線輸出的電源系統，對採用空間矢量控制的四橋臂逆變器進行了深入研究，對三維空間矢量調制方案進行了分析求解、模擬，並給出了適用於15kva變速恆頻電源變換器的解決方案，實現了變換器的三相四線輸出以及線性調壓。 -
In this paper, the upper - class intelligent control scheme is adopted according to the characteristics of tobacco re - dryer and the present control condition in order to solve the problem that the output tobacco moisture can ? keep stable. that is, to keep the old every pid control link, to add the upper - class computer so that sets up the upper - class intelligent control system that consists of the description management sub - system, the fuzzy compensation on line sub - system and the self - learning system. the following are control procedure : first of all, a series of output values of description can be obtained by the forward inference of basic controller on the basis of the information of input tobacco, then, these output values can be adjusted by the fuzzy compensation controller with inquiring the fuzzy control - list on line in the light of the output tobacco moisture error
本文針對烤機的工藝特點和目前控制現狀，提出用上位智能控制的方法解決烤機目前存在的問題，即在保留原有各段pid控制的基礎上，增加上位計算機，建立起由配方管理子系統、模糊在線修正子系統和自學習系統組成的上位計算機監控、決策的智能控制系統；控制過程為：基本配方控制器根據來料信息正向推理提供煙葉復烤機各段參數設定值的基值；模糊補償控制器根據煙葉水分偏差在線查詢模糊控製表提供相應參數設定值的修正值，實現煙葉復烤機參數的在線修正；學習環節的引入實現煙葉配方的在線優化。 -
The flat yarn making machine is adopted micro - processor control, frequency conversion governor and setting and displaying technical data may be fully digitized on the basis of absorbing international advanced techniques. the main parts use quality products. the line enlarges l d ratio and adopts new type of separating screw and widens mixing smelt zone on the extruder screw pot which is specially processed using quality steel, fine plasticized effect, low energy consumption in relation to output
本平膜拉絲機組是我廠在廣泛吸收國外先進拉絲機組技術基礎上，採用微機控制變頻調速及可控硅直流調速等先進技術研製而成的，主要電氣元器件採用國外優質產品，整機結構設計先進控制靈敏運行平穩操作方便安全可靠生產效率高能量消耗低。 -
A new robust adaptive scheme which are used for tracking of this robot with parametric and bounded external uncertainties is proposed in this thesis. the controller is consist of a controller which is proposed by slotine1 ' 1 and nonlinear continued feedback compensation part. by estimating the unknown physical parameters of robot on - line, it can eliminate the effects result by parameters and external disturbances and guarantee gas and uniform boundedness of parametric estimation. the only information required in setting up the strategy is the output states of jionts, while the inversion of the inertia matrix or estimation the bound of the inertia matrix and measure the jionts accelerations are not needed. it is shown by simulations that the proposed control scheme has quicker convergence velocity and better control precision than paper [ 1 ] and control schemes at present
針對該模型具有參數及有界外部擾動不確定性時提出了一種新的魯棒自適應控制策略，控制器由基於slotine的控制器和非線性連續反饋補償控制器構成。通過在線估計機器人的未知物理參數，有效的消除了由參數及外部擾動所引起的不確定性影響，保證系統達到漸近穩定和參數估計一致有界。與現存的許多控制方法相比，該控制策略不需求解慣性矩陣的逆或估計慣性矩陣的界，不需測量關節加速度，而唯一需要了解的只是系統輸出的位置及速度狀態。 -
In order to obtain three - phase four - line ac output, system applied the four - legged main circuit topology. with the 3d - svm, the power system realizes voltage regulation and three - phase four - line output. meanwhile, this kind of control is easy to be realized in the digital inverter
為實現三相四線的交流輸出，變換器電路採取四橋臂新型拓撲，其控制採取了三維空間矢量調制，實現了變換器的在線調壓及輸出中點的形成，具有良好的動靜態性能，且這種控制思想可以方便地在現有數字變換器平臺上實現。 -
Sszm500b straight line double edgers, and 90transfer taboe. 26 spindles on each sszm2500b. plc control system sets processing parameters via interface, and finishes processing at one time. this product has stable structure. precise and smooth transmission system, thetransmission belt drive adopts strong power and transfrequency motor to control speed, constant power, constantrele output and advanced epuipment to control, high polishing efficiency. it is the best matched equipment of large batch of furniture and decorated glass edge production, and production, and can be matched with gluing, printing, reinforcing, etc. production line
才用plc控制系統通過界面設定加工參數一次完成加工，具有穩定扎實的底座結果精確流暢的傳動系統，傳送皮帶驅動採用大功率變頻電機調速控制，恆功率恆扭矩輸出和高配置的控制。結構緊湊，性能穩定可靠，拋光及生產效率高。是大批量的傢具和裝飾玻璃的磨邊生產的最佳配套設備，可以與夾膠印花鋼化等生產線配套使用。 -
In fcmac ' s application in the vertical plane motion control of submarine, its output is used to compensate the effect of the non - linear part of the kinematic model, this function is realized by means of fcmac ' s on - line learning function. the rest of the model can be seen as a linear system, and is controlled by a pid controller
在潛艇垂直面運動控制的應用中， fcmac的輸出用於補償運動模型的非線性部分，這一功能通過fcmac的在線學習實現，經過補償后的潛艇控制系統可看作一個線性系統，它由一個pd控制器進行控制。 -
By studying the characteristics of the eddy displacement sensor, it adopts the control method which include using the fitting line of sensor ' s output characteristic curve in certain block as control characteristic curve, and stipulating door limit district and a certain of backward overshoot, the stabilization of welding torch is gained under the certain track precision
摘要通過對渦流式位移傳感器的特性研究，採用以傳感器輸出特性曲線在一定區間內的擬合直線作為控制特性曲線、設定規定門限區和一定反向調節量的控制方法，得到了在保證一定的跟蹤精度條件下的焊槍穩定。 -
Firstly, design the software phase - closed loops ; secondly, realize the double closed loops control of the instantaneous value and the virtual value. furthermore, the dynamic flux imbalance of the output transformer caused by ordinary pi arithmetic is analyzed in detail. a new solution for flux balance by sampling the instantaneous primary current of the output transformer and introducing the on - line calculated bias current component into the voltage regulation arithmetic is presented
系統軟體實現了ups的各個功能模塊，首先設計了軟體鎖相環；然後實現了輸出電壓瞬時值和有效值雙閉環反饋控制；並且在深入分析基本數字pi演算法所引起的輸出變壓器動態偏磁問題的基礎上，提出了一種改進演算法，實時消除了變壓器的偏磁。 -
Using this novel start - up circuit structure for the off - line switching model power supply ic can save the cell area, reduce the power consumption of the circuit, and easily control and supply the larger output voltage
採用該結構集成開關電源的啟動電路可以節省晶元面積，降低電路功耗，易於控制且可提供較大的晶元內部電源電壓。
分享友人