output drift 中文意思是什麼
output drift
解釋
輸出信號變化-
Then two kinds of drift errors, which caused the decline of output video quality, were educed based on the theoretic analysis, and another kind of drift error, which was unique for transcoding in dct domain, was studied
然後，根據理論分析，推導出了造成轉碼系統輸出視頻質量下降的兩種漂移誤差，並通過對不同結構轉碼系統模擬結果的比較，得出了dct域轉碼所特有的一種漂移誤差。 -
Performance for a piezoresistive transducer pressure sensor to thermal and pressure environments can be predicted by finite element method. a simplified 1 / 8 model, considering silicon dioxide and nitride process as well as stack anodic bonding and adhesive bonding processes, was developed. the fem results were found to be comparable to experimental data. case studies suggested that pyrex stack induces certain amount of non - linearity, while it isolates hard epoxy nonlinear effect. flexible epoxy bonding or soft adhesive bonding is preferred to the packaging process. the viscoelasticity and viscoplasticity of bonding material will result in hysteresis and drift errors to sensor output. however, soft adhesive s influence on sensor can be ignored under relative stable environments. more over, detailed design and process information will help to improve modeling application
熱、壓環境下壓阻變換壓力傳感器的性能可以通過有限元方法預測.這里研究了簡化的1 / 8模型，模型考慮了二氧化硅和氮化硅生成過程及堆陽極鍵合和膠粘結合過程.結果發現有限元預測結果和實驗數據具有可比性.範例研究表明，硼硅堆導致產生一定的非線性，但它隔離了硬環氧樹脂的非線性.在包裝過程中最好使用柔性環氧黏合或軟黏膠性結合.黏合材料的黏彈性和黏塑性將會導致傳感器輸出的滯后和漂移誤差.然而，在相對穩定的環境下，軟黏合劑對傳感器的影響可以忽略.此外，詳細的設計和過程信息有助於提高模型的適用性 -
This product is a full electron construction in which its front - end adopts pressure sensor with baffle filled oil chip. output signal is sent the data to microprocessor from high - precision, low temperature drift and high - reliability amplification circuit and a d convert circuit, after operating, to transform by high - precision d a convert circuit into standard signal output
該產品為全電子結構，前端採用帶隔離膜充油芯體的壓力傳感器，輸出信號由高精度低溫漂和高可靠性的放大電路和模數轉換電路將數據送入微處理器，經運算後由高精度數模轉換電路變換為標準信號輸出。 -
Since it has the advantage of no moving components, impulse signal output, strong medium adaptability, high measurement accuracy, wide measurement range, low - pressure drop, no zero drift and easy to maintenance, it is wide accepted that the vortex type fluid oscillatory flowmeter is ideal flowmeter in the measurement of gas, liquid, steam and mix / corrosive fluid
這類的流量計兼有無運動部件，脈沖數字輸出，計量不受被測流體性質影響，測量準確度較高，量程比寬，無零點漂移，壓力損失小，便於安裝維護等優點，是測量氣體，液體，蒸汽，混合型和腐蝕性流體的理想的流量計。 -
To avoid the actuator, a capacitor load being charged up by the drift current of the amplifier, a secondary feedback from the output of the amplifier has been used and expected result has been gotten
針對驅動器輸出電流漂移造成的壓電作動器（容性負載）電荷積累，文中引入了抑制驅動器電流漂移的反饋環節，取得了預期的控制效果。 -
In dtc system, the concept of space vector is introduced to analyze and control the ac motor, the electromagnetic torque and flux are caculated and controlled in the stator reference frame, and the optimal pwm gating signas are generated to control the inverter according to the output of the bang - bang regulator. in this paper, the dtc system is designed based on dsp. a speed estimation method is derived detailedly and the sensorless speed close - loop control is conducted. in this system, there are some problems, such as flux drift and torque ripple. to resolve these problem, a modified flux caculation method and some measures such as speed lpf, torque slide filtering are adopted. the system performance is enhanced by these mersures
直接轉矩控制採用空間矢量的概念來分析異步電機的數學模型和控制其各物理量，直接在定子坐標系中計算和控制轉矩和磁通，藉助于離散的兩點式調節（ bang - bang控制）產生pwm信號，直接對逆變器的開關狀態進行優化控制，以獲得轉矩的高動態性能。本文採用dsp設計了直接轉矩控制系統，詳細推導了速度估計方法，進行了無速度傳感器的速度閉環控制。 -
Low temperature drift and high stability of output voltage is of key importance to an ideal voltage reference. they are also the focus of this paper
溫度和電壓穩定性是基準電壓源的重要指標，直接影響電路和系統的穩定性及多項性能指標，亦是本文設計中關註解決的重點。
分享友人