overshoot voltage 中文意思是什麼
overshoot voltage
解釋
過電壓，過沖電壓-
In the positioning servo - system, which generally is configured by the d. c. pulse width modulator ( pwm ) velocity governing system and position servo - loop, the parameter perturbance of pwm velocity loop really exist by reason of such as the load behavior ; power voltage supply ; operating setting value, etc. 1, 2 ， and it cannot be ignored. by using the identification technique to form the mathematical model of the system, authors have confirmed the facts. therefore, to design the discrete sliding mode controller ( dsmc ) of the positioning servo - system, the perturbed parameters value bounds of the pwm velocity loop, which is as the controlled plant of position servo - loop, should be accounted. consequently, the design principle of dsmc for accounting system with parameter perturbance is proposed by the authors. the proposed method can ensure the stability of system with parameter perturbance and the behavior of non - overshoot, fast precise positioning. in order to reveal the effects of the design method, the comparative research work is done by the authors. also, it has been tested in an industrial experiment, the results proved it is satisfactory
由直流脈寬調速系統（ pwm ）和位置環構成的定位系統中，速度環的參數隨負載特性；電網電壓；給定工況而攝動是不容忽視的.作者通過系統辨識建模也證實了這一事實1 ， 2 .因此在設計位置環的離散滑模控制時，必須針對速度環（即位置環的控制對象）的參數攝動范圍採用「對象參數攝動離散滑模控制器的設計方法」 ，以確保系統在參數攝動時的穩定性和快速、無超調、準確定位的優良動態品質.為剖析該設計方法的控制效果，本文作了對比性研究，並將該設計方法用於工業試驗中，取得了滿意的結果 -
This converter not only retains the advantages of ttfc but also has only two camping diodes. moreover the proposed converter operates at nearly unity duty - ratio for very high efficiency and eliminates the voltage overshoot of the output rectifying diodes
本文提出了一種新型直直變壓器拓撲，該拓撲不僅保留了雙管正激變換器的優點，而且在原邊僅含兩個續流二極體，電路結構簡單。 -
Based on comparison between the parallel - parallel and parallel - serial combination ttfc, a novel two - transistor forward converter with parallel - serial / serial combination is proposed. this converter reduces greatly the current overshoot of the primary side switches and the voltage overshoot of the rectifying diodes. moreover, the size and weight of the converter can also be reduced by interleaving technique and increasing frequency
本文在對並-串型和並-並型雙管正激組合變換器進行了詳細比較研究的基礎上，提出了一種新型並-串串型雙管正激組合變換器，該組合變換器可以大大減小原邊開關管的電流應力和副邊整流電路中二極體的電壓應力；通過交錯控制及提高開關頻率，大大提高了變換器的功率密度。 -
Thirdly, the snubbers are designed to compress the switching voltage transient. when igbt is abruptly turned off, trapped energy in the circuit stray inductance is dissipated in igbt, causing a voltage overshoot and damaging igbt. this paper analyzes the principle of the snubber and discusses the impact of the parameters of the snubber on voltage overshoot
針對igbt工作過程中出現的電壓尖峰、電流尖峰和大的開關損耗問題，本文首先從理論上詳細分析了igbt逆變橋緩沖電路的工作原理，推導出緩沖電路各元件的參數計算公式，討論了緩沖電路各元件參數對關斷電壓波形的影響並進行了模擬分析。 -
In order to conquer the shortcoming of the un - ideal dynamic with taking traditional pid control strategy, it uses fuzzy + pid control strategy to the close loop of the output current and voltage, the control way is realized with software program in the processor. the emulation results shows the fuzzy + pid control strategy which is used in the electroplating power has good dynamic performance, little overshoot and the good static precision
針對傳統pid控制策略動態性能不理想等缺陷，本文研究了電流和電壓模糊+ pid閉環控制系統，對電鍍電源的輸出電流、電壓控制進行了控制演算法設計，模擬結果表明模糊+ pid控制系統具有超調量小、動態響應快，穩態誤差小的特點，優于傳統pid控制。
分享友人