partial deformation 中文意思是什麼
partial deformation
解釋
部分形變- partial : adj 1 一部分的，局部的，不完全的。2 不公平的；偏袒的。3 偏愛的，特別歡喜的 （to）。4 【植物；植物...
- deformation : 變形,走樣
-
The commonly used methods of connections, especially the high - strength bolted connection and welding with bolting mixed connections are discussed in more detail. the analysis for the problems, such as partial penetrated butt weld and welding deformation is also discussed in the paper
對工程中採用較多連接如高強度螺栓連接、栓-焊混合連接等作了較深入分析；對工程中容易出現問題連接如不焊透的對接焊縫計算方法及可能出現的焊接變形及處理等問題也作了較深入探討。 -
Analysis which was based on the fracture mode of mould in wire - cutting processing, and the results show that the partial - quenched of mould, the non - uniformity of blank temperature and the carbide segregation inside the material are the main reasons of deformation and cracking
摘要通過分析在線切割加工中模具的破壞形式表明：模具不完全淬火、坯料溫度的不均勻分佈、材料內部的碳化物偏析是模具變形與開裂的主要原因。 -
In this thesis, it is analyzed theoretically the steel bar layout pattern, the prestress loss, the concrete stress, and the discipline of the deformation and the fracture forming of structures of the partial prestress concrete frame beams, which is widely used in modern civil engineering
本文從理論上分析了現代建築工程中廣為採用的部分預應力混凝土框架梁的布筋方式、預應力損失、混凝土應力、結構變形和開裂規律；導出了具有一般意義的預應力錨固損失以及梁的長期撓曲變形計算公式。 -
On the basis that characteristics of every forming methods have been summarized and concluded, according to the moving relationship between working parts of die and block, it is proposed the successive partial plastic forming methods for groove have been divided to two kinds of basic deformation styles, rolling and splitting extrusion
在總結歸納各種方法變形特徵的基礎上，根據模具工作部分與坯料之間的運動關系，提出槽的連續局部塑性成形可劃分為滾軋與劈擠兩種基本變形方式。 -
The microprocesses of deformation and fracture in 18 - 8 stainless steel were observed by in - situ tension in tem. it was found that the dislocations were emitted from the grainboundary and dislocation source inside a grain and slip along their slip system respectively. partial dislocation could also be emitted from the grainboundary, and moved into the grain, and that leaving behind a stacking fault
摘要浙江人學博1 ：學位論文採用透射電鏡動態拉伸、原位觀察icrlsnigti不銹鋼形變與斷裂過程，發現不銹鋼變形時，晶界和晶內位錯源均可產生位錯，並沿各自的滑移系運動。 -
The partial liquid phase during superplastic deformation of 2024 aluminum alloy - matrix composites reinforced with sic particulates ( pm - sic ( subscript p ) / ly12 ) by powder metallurgical ( pm ) processing was studied usina sem etc
摘要用掃描電鏡等方法對碳化顆粒強化ly12鋁合金基復合材料超塑變形時出現的局部液相現象進行了研究分析。 -
Reducing partial rigidity : when closed weld or the weld which has less rigidity are welded, we can take anti - deformation way to reduce the partial rigidity of component
降低局部剛性：焊接封閉焊縫或其剛性較大的焊縫時，可以採取反變形法來降低結構的局部剛性。 -
In accordance with the characteristics of repeated impact load, and from the aspects of stress wave transmission, repeated impact wear, hardening and softening of repeated impact and plastic deformation of repeated impact, an experimental study on partial mechanics behaviors of samples bearing laser melted clad coating under repeated impact load was carried out
摘要根據多次沖擊載荷的特性，從應力波傳播、多沖磨損、多沖硬化與軟化和多沖塑性變形方面，對帶有激光熔覆層試樣在多沖沖擊載荷下的部分力學行為進行了試驗研究。 -
( 4 ) which deformation behavior of cementite lamellae in pearlite colonies is closely related to the stress state of cementite which significantly depends on cementite thickness and orientation, especially on cementite thickness. ( 5 ) the lamellar cementite undergoes partial dissolution on the present deformation. the thermodynamical destability of cementite is attributed to a large number of defect in cementite introduced by severe plastic deformation providing evidence for cementite dissolution
而滲碳體的應力狀態主要是與滲碳體的片層厚度和取向密切相關的，其中滲碳體的厚度起決定性作用； （ 5 ）本實驗變形條件下，滲碳體出現了部分溶解的現象，這是由於強烈塑性變形而在滲碳體中引入大量的缺陷導致其處于高能不穩定狀態從而促使了滲碳體溶解。
分享友人