photoelectric sensors 中文意思是什麼
-
Magnetic sensors are an important branch that can be used to detect the non - electronically characteristics through the magnetic field. the insb magnetoresistance photoelectric sensor in this paper is designed for the fine measurement of the photosignal of the luminant device. through the sensor, the photo - pulse signal is changed to electric pulse which can provides to other second instruments
通過磁場的無接觸特性，對非電量的測量是磁傳感器應用的一個重要方面，本文所研究的銻化銦磁阻型光電傳感器即是針對于發光物體的光脈沖信號進行高精度無接觸測量的一類傳感器，它可以把光脈沖信號轉換成電脈沖信號，供二次儀表使用。 -
The algorithm can not only eliminate the influence of the cumulative errors of the photoelectric code recorder, but also it can satisfy the requirement of the real - time control. a direct inverse model controller of fuzzy neural network with changeable structure based on takagi - sugeno inference is presented and it is used to the motion control of mobile robot. in order to avoid the obstacles successfully, detection results from ccd and ultrasonic sensors are fused by a fuzzy neural network, which acts as an avoidance controller
包括移動機器人的融合自定位問題：移動機器人利用光電編碼器進行自定位，同時用擴展卡爾曼濾波器融合多個超聲波傳感器的測量值，採用回朔演算法將融合值用於復位光電編碼器，消除了光電編碼器累積誤差的影響，並能滿足實時控制的要求：並提出一種基於takagi - sugeno模型的變結構模糊神經網路直接逆模型控制器，並應用於移動機器人的運動控制；利用模糊神經網路避障控制器融合ccd攝象機與超聲波傳感器探測到的環境信息，以實現機器人的安全避障。 -
After the construct of the motion simulation model, genetic algorithm is used to do the adjustment of pid parameters of the control system of the joint motors, integral separation pid control and angle error analysis is finished, and three force / torque sensors, touch sensors, distance sensors and photoelectric switches are calibrated and installed
在建立了機器人關節控制系統模型后，使用遺傳演算法對其關節電機控制系統進行pid參數整定，進行機器人關節的積分分離的pid控制策略和轉角誤差的理論分析，並進行了機器人三維力/力矩傳感器、接觸傳感器、測距傳感器和光電開關的標定與安裝。 -
Proximity switches, photoelectric sensors ; flow sensors, pressure sensors, temperature sensors, encoders, speed monitors, as - i bus systems, plcs for vehicle
近接開關光電開關流動監視器速度監視器壓力感應器溫度感應器編碼器asi總線系統車輛專用plc -
The pixel size of p + / n - well / p - sub structure is 100 umx 100 n m, fill factor is 77. 6 %. it can obtain target information with illuminance intensity in the range of 0. 011x ~ 98, 0001x, and the sensor photoelectric sensitivity is 35v / lx ? s. when the method of changeable reset frequency double scanning is used, the photoelectric dynamic range can be 139. 8db, which is high in the 0. 6 um level cmos image sensors already reported
在對感光單元進行器件物理結構優化的研究中，通過採用深結深光電管結構，提高了傳感器的感光響應，其中p m階」襯底結構的傳感器面積為100umx100urn ，感光面積百分比為77石，可對0刀98 ， 000lx照度的目標信號進行傳感，感光靈敏度大於3sv ix ? s ，採用了變頻兩次掃描后，動態范圍可達139 -
This machine adopts a non - contact measurement method. all kinds of inspection devices such as photoelectric switch, laser measuring sensors and super voice wave measuring sensors etc are used in the measurement progress
本機全部採用非接觸式測量方式，跟蹤探測掃描使用了安全光幕、光電開關、激光測距傳感器、超聲波測距傳感器等多種傳感檢測探測設備。 -
The technique core of the 3 - d outline tracking scan lies in the adoption of several photoelectric sensors, laser measuring sensors and super voice wave measuring sensors to carry on probing, the single chip makes the photoelectric signal examined as the control basis, and controls the step motor to drive measurement machines and probing sensors to make outline tracking and scans movement along high and breadth direction of the vehicle, and record its outline track, and the data measured is delivered to the computer, finally, acquires the size of the vehicle checked through the place of computer data processing
三維輪廓跟蹤掃描技術的核心在於採用多套光電傳感器、激光測距傳感器、超聲波測距傳感器進行探測，單片機把檢測到的光電信號作為控制依據，控制步進電機驅動測量機及探測傳感器在車長、車高和車寬方向上作輪廓跟蹤掃描進給運動，記錄其輪廓軌跡，並把測得的數據傳送到上位機，經上位機數據處理獲得被檢車輛的特徵尺寸。 -
The conventional quadrants sensors mainly have 4 or 8 quadrants, which are not integrated with the signal processing circuits in one chip but are soldered with the discrete signal processing circuits. in this way, it ' s difficult to realize the micromation and system optimization of the devices. in addition, there are few number of photoelectric sensor parts in conventional quadrants sensors, which limits the targets information got from the conventional quadrants sensors
傳統的硅象限傳感器主要採用四象限，八象限的結構，採用焊接的方式將分別製造的感光象限和電路結合在一起，不能實現感光象限與信號處理電路的單晶元集成，難以實現器件的微型化和系統優化；同時，傳統象限傳感器的感光象限單元數量較少，獲取的目標信息有限，難以實現對目標的坐標位置獲取、形狀識別等功能。 -
The work shows that sodium titanate nanowires may be used potentially as gas sensors and photoelectric sensors
研究表明上述納米器件可用作氣體探測器和光電探測器。
分享友人