pole press 中文意思是什麼
pole press
解釋
打樁機-
During the winding of magnetic pole coils used in synchronous electric motors, cold hardening is induced by press bending at 90, by which the coils are hard to be pressed and shaped, thus local resistivity increases and results in influence on the coil lifetime
摘要同步電動機磁極線圈在編繞加工時， 90角處因壓彎而產生的冷作硬化現象使線圈無法裝壓成型，且局部電阻率增大，甚至影響磁極線圈使用壽命。 -
A lot of experiments have been done in the process of exploiture soft packaging li - ion battery about how to choice the rational arts and crafts. the content include : how to deal with the collector, add how much pvdf in the material, how long the material need to stirring and the right viscidity, how much condubtivity agent the electrode need, what theckness is best, choice different collectors, the degree of dryness of the electrode, theckness of pressed model, how much electrolyte will be added, placement how long after added the electrolyte, system of formation how to influnce the battery, in formation the battery need or not need preesure from outside, how to vacuumize and the optimize matching positive pole and negative pole. with these practice make sure the parameter of the positive pole should less than 90 m ; according to different vacuumize order the conduc - tivity agent in anode will be 5mass % and 9mass %, respectively, and in cathode the data is 2mass % ; every 100mah added to 0. 4 ml electrolyte ; before formation the battery should be placement 8 hours and the system of formation must be less than 0. 01c before the voltage reach to 3. 0v ; should press in outside when battery in formation ; to these batteries which capacity more than 350mah the vacuum time not excess 15s ; the optimize matching positive pole and negative pole between 2. 10 : 1 and 2. 15 : 1. finally make out the battery which cycling performance and security are all very well
液態軟包裝鋰離子電池的研究主要是對關鍵工藝進行了優化設計，具體包括:集流體的處理、 pvdf的加入量、漿料攪拌時間和粘度、導電劑的加入量、電極膜的厚度、不同集流體的選擇、電極膜的乾燥程度、壓型的厚度、電解液的加入量、注入電解液后靜置時間的長短、化成制度的影響、化成時電池所具有的壓力影響、抽真空的處理、正負極活性物質的匹配。最後確定出液態軟包裝鋰離子電池最佳工藝參數:正極膜的厚度小於90 m ;根據化成時不同抽真空順序，確定正極膜中的導電劑的加入量分別為5mass %和9mass % ;負極膜中導電劑的加入量為2mass % ;電解液的加入量為每100mah添加0 . 4ml ;化成前電池的靜置時間應當大於8h ;電池在3 . 0v之前採用小於0 . 01c的化成制度;在化成過程中應當施加一定的外部壓力;對於350mah的電池抽真空的延時不應大於15s ;而正負極活性物質的質量比應當在2 . 1 : 1 2 . 15 : 1之間。 -
Control on the stage most the left side 2s to pull the pole draw down, again most the right side 2s pull a pole to press, pressing the red button after, getting white glasses
控制臺上最左邊兩支拉桿拉下，再把最右邊兩個拉桿按下，之後按下紅色按鈕，得到白色眼鏡。 -
Electron gun is the foremost parts of twt, it can produce electron beam with a certain shape and current, in order to guarantee the reliability and security of work, it ’ s design have to meet to the requirement not only of electric parameter, but also all kinds of subsidiary characteristics such as filament pyrogenation efficiency, warm up time, shape size, pole space capacitance and the ability to be able to bear the press and all kinds of rigorous run conditions such as high temperature, high humidity, low air pressure, strong vibration and great strike
由於行波管的大功率和高頻率等特性，目前還沒有任何其他的器件可以代替。行波管是應用高頻電磁場與電子注進行互作用的機理進行工作的，而電子槍是行波管中產生電子注並使它成型的基本部件，電子槍的結構設計決定了槍體自身必須具有良好的抗振可靠性，否則結構發生共振或振動位移過量，就會導致行波管的失效。因此對行波管電子槍的研究具有非常重要的意義。 -
Can adopt the misty and robustness design method and base on to pull - press pole model method etc.
可以採用模糊穩健設計方法、基於拉-壓桿模型方法等。 -
The present conditions of cold - squeezing equipments and technology have been introduced with the emphasis on the characteristics and the usage situation in the cold - squeezing press of elbow - pole type
摘要介紹了冷擠壓設備的技術現狀，重點闡述了肘桿式冷擠壓力機的類型和各自的特點與使用場合。 -
6. recruitedbattery shell technology and would go on mass - producing. 7. the third generation double deform spindle connected pole press was improved and cutting design would prolong tool life. from 50000 times to 150000 times
7 .第三代雙曲軸連桿沖床改善及模板分割設計，以增加模具壽命從50 ， 000次到150 ， 000次。
分享友人