position deviation 中文意思是什麼
position deviation
解釋
位置偏差-
As to the critical technological problems of the interlock control of three - car coke oven - oven number identification, accurate contraposition and data transmission, the author proposes solutions respectively - rfid, three - light positioning device, coke oven controller and radio transmission network. these solutions can ensure accurate identification of the oven number. for example, the deviation of the automatic parking position is within 10mm
針對三車聯鎖控制環節的關鍵技術：爐號識別、精確對正和數據通信，本系統採用了射頻識別（ rfid ）裝置、三燈位置檢測裝置、焦車控制器、無線通訊網路等解決方案，可實現無差錯的爐號識別，自動停車定位誤差在10mm以下，通信數據可靠等系統要求。 -
To find a solution to the deviation between center position of strip and process line, a kind of method for strip centering control with inductive sensor is proposed
摘要針對帶鋼跑偏問題，介紹了採用電感式檢測裝置進行檢測的糾偏控制方法。 -
Her charm lies in her three subsistent states in american civil war : namely subsisting competition and self - fission ; the temptation of money and self deviation ; in pursuit of love and self - difficult - position
她之所以有經久不衰的魅力，在於郝思嘉形象所蘊涵的生存競爭與自我裂變、金錢誘惑與自我背離、愛的追尋與自我困境的三類不同的自我生存狀態。 -
According to the moving characteristics of tracklayer, when the vehicle is on ramp and the ground ' s vertical pressure is linear, the calculating formulas of relationship between the deviation of the instantaneous steering center, the position of vehicle ' s gravity, steering radius, moving velocity, moving acceleration, and vehicle ' s orientation, were obtained by the theory and method of vector analysis in mathematics and mechanics
摘要根據履帶式車輛的運動特點，運用數力學中矢量分析理論和方法，推導了接地比壓為線性分佈時履帶式車輛在斜坡上轉向時，瞬時轉向中心偏移量與車輛重心位置、轉向半徑、行進速度、加速度、車輛方位相互關系的計算公式。 -
The exterior factor primarily includes four aspects : the value ' s deviation, impugnation of pedagogy ' s independent position, the impact of the " scientific discipline " and the practical research custom
外部固素主要分析了四個方面：價值觀念的偏差、教育學獨主地位的質疑、 「學科科學化」的沖擊和研究風氣的實用化。 -
The design guideline of the plastics products with insert film decoration and the position deviation experience tolerance of the film pre - form process are discussed
同時討論了模內復膜產品設計原則以及裝飾膜的預成型工藝及其公差經驗值。 -
Intelligent actuator receives the output signal from the regulator and compares it with valve position feedback signal and obtains output signal which is directly proportional to the output signal of regulator according to the deviation between the signals and then control the pneumatic actuator
智能執行器接受調節器的輸出信號，在與閥位反饋信號進行比較，然後根據兩者的偏差產生和調節器輸出信號成正比例的輸出信號控制執行器。 -
In order to research the influences produced by sidetracking position, the primary hole deviation and azimuth of used wells on the primary section of the re - entry horizontal wells, it is necessary to consider the 3d trajectory design of the re - entry horizontal wells
為了考慮側?點位置及老井的初始井斜、方位對側?水平井起始段的影響，需要對側?水平井進行三維軌跡設計考慮。 -
When the deviation between the placing position and construction reference line of caisson for gravity wharf is big enough, the verticality of upper structure, i. e. crest wall will be affected, and furthermore the visual quality of the wharf will be influenced
摘要重力式碼頭沉箱安裝的位置與施工準線的偏差過大，會影響上部結構胸墻的豎直度，進而影響到碼頭觀感質量。 -
Landing must come slowly, if lowering the landing position too fast or slight deviation on monkeys will suffer
著陸時一定要慢慢落下，如果降的太快或者降落位置稍有偏差，猴子就遭殃了。 -
The examples in abroad and home indicate that the viscous remanent magnetization is a convenient tool for orientation determination of drilled cores. it can be used on samples for which the geological age is not known. the only information required is well position, the direction and magnitude of well deviation and the " right way up " for the core sample
結合國內外的研究實例和自己的研究實例，對利用粘滯剩磁確定巖心方向進行了較深入的研究，進一步證明了粘滯剩磁巖心定向是一種不用考慮復雜的地殼運動和地質年代，只需要井位的井斜數據和取心方向標記的簡單、方便值得推崇的方法。 -
Two guidelines were defined to evaluate the selective assembly quality : matching rate and assembly precision, and two computer - aided selective assembly methods were suggested : the matching according to the average deviation of the closing link and the matching according to the ideal size position of the closing link
摘要定義了評定選擇裝配質量的兩個指標：匹配率和匹配精度，提出了計算機輔助選擇裝配的兩種基本方法：按封閉環理想尺寸位置匹配和按封閉環平均偏差值匹配。 -
The 0. 001mm dial indicators are a high accuracy length measuring tool. they are widely used for measuring the geometric deviation and position deviation of workpieces
千分表是一種高精度的長度測量工具，廣泛用於測量工件幾何形狀誤差及相互位置誤差。 -
Top - directly as a basis and foundation of the bearing surface as the top - embedded steel bearings or bearing surface, the supporting surface, the anchor bolt ( anchor ) position should be consistent with the allowable deviation of norms
基礎頂面直接作為柱的支承面和基礎頂面預埋鋼板或支座作為柱支承面時，其支承面、地腳螺栓（錨栓）位置的允許偏差應符合規范的規定。 -
About the confirmation of the position evaluation factors scale, the thesis has put forward using the fuzzy analytic hierarchy process ( fahp ) to evade subjective factor influence and make the position evaluation system more scientific. the thesis makes use of mathematics tools, such as the standard deviation of the sample, variation coefficient, etc. to analyze the deviation that the judge panel give a mark, and carry on effective correct ing
其中在崗位評價因素權重的確定問題上，提出藉助模糊層次分析法（ fahp ）的系統理論來規避主觀因素的影響，使崗位評價體系的設計更趨科學化；還利用樣本標準差、變異系數等工具來分析評委打分的偏差，進行有效的糾錯處理。 -
The mechanical dial compartors are used for measuring the size deviation and position deviation of workpieces
詳細說明：杠桿齒輪比較儀用於測量工件形狀誤差和位置誤差。
分享友人