pressure (sensor) 中文意思是什麼

pressure (sensor) 解釋
硅電容式絕對壓力傳感器
  • pressure : n 1 壓；按；擠；榨。2 【物理學】壓力，壓強；大氣壓力；電壓。3 精神壓力，政治[經濟、輿論等]壓力。4...
  • sensor : n. 1. ＝sensory （名詞）. 2. 【自動化】感受器；傳感器；靈敏元件，控制儀板上顯示溫度、輻射量等變動的裝置。
  1. Bap sens barometric absolute pressure sensor

    大氣絕對壓力傳感器
  2. Bps barometric pressure sensor

    大氣壓力傳感器
  3. Pressure sensor and hygrothermograph sensor are adopted respectively to sense these change ; a plc and its analogue cell are adopted to collect and analysis the data ; a mcgs component software is used to process and store the data in real time

    給出了以壓力、流量和溫濕度傳感器為測量元件、以plc為主控制器、 plc模擬單元為數據轉換單元的詳細硬體設計、程序設計和組態軟體mcgs在上位機的運用。
  4. A compensatory approach to software and hardware used by microprocessor was applied to the intelligent solid pressure transducer, which not only achieved the intelligentization of pressure sensor, but also improved the sensor ' s accuracy. this will surely accelerate the development of instrument towards the direction of multifunction, high degree of accuracy, numeralization, intelligentization, modularization and miniaturization so that measurement system will be further improved

    為此本課題研究固態壓力傳感器的製造技術，通過微處理機的軟體和硬體的補償方法來提高傳感器的精度，實現壓力傳感器的智能化，促使儀表向多功能、高精度、數字化、智能化、模塊化、小型輕量化方向發展，近而得到一個較為完善和理想的測控系統，提出了一種差壓傳感器智能化設計方案。
  5. Design of wind tunnel pressure test system based on vibrating cylinder pressure sensor

    基於振動筒傳感器的風洞壓力檢測系統
  6. Secondly, the pressure sensor made by motorola co. ltd. in usa is chosen as the key part of the pneumatic - electric transducer. thirdly, the signal processing system of the pneumatic - electric is developed

    第三，研製了氣電轉換器的信號處理電子系統，設計有調零、增益調整、開關轉換擴展量程等功能。
  7. In this paper, basic pneumatic - measuring theory and air circuit system working principle are introduced. the pneumatic - electric transducer employs a mpx5500dp silicon pressure sensor which converts air pressure signal into voltage signal, and displays on the electron column after the signal conditional circuit s processing

    本課題從分析氣動測量的基礎理論入手，研究氣路系統的工作原理，用mpx5500dp擴散硅壓力傳感器將氣體壓力信號轉換為電壓信號，進而研製成功一種氣電轉換器。
  8. According to the characteristics of the load on the canopy, the method for measuring the load on the canopy with a pressure sensor is presented, and then the flight measurement of the load spectrum of the canopy is realized for the first time

    根據實測活動艙蓋載荷曲線特點，提出了任務類型劃分方法，建立了活動艙蓋載荷譜數據統計方法和載荷譜編制方法，並依此編制出k8飛機活動艙蓋載荷譜。
  9. The improvement system is made up of the pressure sensor, flow sensor, displacement sensor, electro - hydraulic proportional flow control valve, power amplifier, data gathering board and computer. the platform can carry out testing the hydraulic parameters, processing the tested data, saving the processed data and drawing, adjusting the pressure automatically

    改造后的測控系統主要由壓力傳感器、流量傳感器、位移傳感器、比例節流閥、功率放大器、數據採集卡和計算機組成。改造后的實驗臺具有自動採集實驗數據、自動處理實驗數據、自動保存實驗數據、自動調節液壓系統負載壓力等功能，大大提高了實驗臺的工作效率、測試精度和智能化水平。
  10. The front flush pressure diaphragm avoids zones, in which medium could crystallize or residues could form, thus ensuring trouble - free pressure measurement and hygenic cleaning of the pressure sensor

    前置的壓力膜片可以避免介質結晶或殘留產生的空間，這樣就可以保證精確的測量和傳感器的衛生清潔。
  11. Intake air pressure sensor

    進氣壓力傳感器
  12. Performance for a piezoresistive transducer pressure sensor to thermal and pressure environments can be predicted by finite element method. a simplified 1 / 8 model, considering silicon dioxide and nitride process as well as stack anodic bonding and adhesive bonding processes, was developed. the fem results were found to be comparable to experimental data. case studies suggested that pyrex stack induces certain amount of non - linearity, while it isolates hard epoxy nonlinear effect. flexible epoxy bonding or soft adhesive bonding is preferred to the packaging process. the viscoelasticity and viscoplasticity of bonding material will result in hysteresis and drift errors to sensor output. however, soft adhesive s influence on sensor can be ignored under relative stable environments. more over, detailed design and process information will help to improve modeling application

    熱、壓環境下壓阻變換壓力傳感器的性能可以通過有限元方法預測.這里研究了簡化的1 / 8模型，模型考慮了二氧化硅和氮化硅生成過程及堆陽極鍵合和膠粘結合過程.結果發現有限元預測結果和實驗數據具有可比性.範例研究表明，硼硅堆導致產生一定的非線性，但它隔離了硬環氧樹脂的非線性.在包裝過程中最好使用柔性環氧黏合或軟黏膠性結合.黏合材料的黏彈性和黏塑性將會導致傳感器輸出的滯后和漂移誤差.然而，在相對穩定的環境下，軟黏合劑對傳感器的影響可以忽略.此外，詳細的設計和過程信息有助於提高模型的適用性
  13. Aiming at the high - speed impact characteristics of fuze pressure sensor when the percussion of the projectile, according to the requirement of developing fuze pressure sensor, the method of anti - ballistic simulation was adopted to design a suit of performance measuring device it could dynamically calibrate and simulate the process of collision between the projectile and the targets at the different angles and speeds

    摘要針對引信壓力傳感器在彈丸著發時處于高速沖擊狀態的特點，根據研製引信壓力傳感器的要求，採用反彈道模擬的方法，設計了一套既可對傳感器進行動態標定又可模擬彈丸以不同著角、不同速度碰撞目標時對傳感器進行性能測試的裝置。
  14. The simulation and manufacture of the end cap pressure sensor

    端蓋壓頭模擬與研製
  15. Study on multiplayer medium film of strainless steel pressure sensor

    應變式鋼杯壓力傳感器的多層介質膜研究
  16. The selected pressure sensor in wide plus k1 series universal pressure transmitter, is a fully welding stainless steel structure which built - in solid pressure sensing chip with stainless steel isolation membrane

    Wideplus - k1系列通用壓力變送器選用的壓力傳感器，是一個內裝固態壓力敏感晶元的帶不銹鋼隔離膜片的全焊接不銹鋼體。
  17. After short introdution about the mathematics model of the semiconductor pressure sensor, it was described that was the holistic design thought of the sensor which reserched into, from the format design, the separated retia slice, sensitive orgen of strucsure and the overall design thought for stucsure point of design

    在簡要介紹了半導體壓力傳感器的數學模型后，從版圖、隔離膜片、敏感元件的結構、整體結構等方面的設計，闡述了對所研製的傳感器的整體設計思想。
  18. Aim at high pressure high temperature well practice engineering question in field development engineering, especially cnpc southwest oil gas branch gas recovery academy project ' s concretion demand, based upon in existence measuring and testing techniques foundation, the dissertation produce a sort of new optical fiber downhole high pressure high temperature test system, and finish downhole fibre optic pressure sensor ' s design

    本文針對油氣田開發工程中高溫高壓井的實際工程問題，特別是cnpc西南油氣田分公司采氣工程研究院科研項目的具體要求，在分析研究現代測試技術基礎上，提出一種新型的光纖式井下高溫高壓測試系統，並主要完成了井下光纖壓力傳感器的設計。
  19. A novel fiber bragg grating pressure sensor with high sensitivity

    一種新型高靈敏度光纖布拉格光柵壓力傳感器
  20. A new method to improve pressure sensor precision based on rbf neural network

    神經網路提高壓力傳感器精度的新方法
分享友人
分享到 Line

分享到臉書