process chamber 中文意思是什麼
process chamber
解釋
處理室-
Before the wide spread adoption of contact process, the chamber process was used.
在接觸法普遍採用之前，使用鉛室法。 -
The main tests and researches are as following : to study the ac flashover characteristic of composite insulator in different icing states by imitating tests in multifunctional artificial climate chamber, and analyze the effect of ice amount and icing water conductivity on flashover voltage, put forward a flashover mechanism by analyzing the icing flashover process. to study the ac flashover characteristic of composite insulator in different altitude and icing states together by imitating tests in multifunctional artificial climate chamber, and mainly analyze the effect of altitude ( air pressure ) and ice amount on flashover voltage, and investigate the flashover mechanism. to investigate the effect of high altitude and icing on the hydrophobicity of composite insulators
本文主要進行了以下試驗研究： 1 ）在多功能人工氣候室里模擬不同覆冰程度下合成絕緣子的交流閃絡特性，主要分析覆冰量和覆冰水電導率對閃絡電壓的影響，並對其覆冰閃絡過程進行機理分析； 2 ）在多功能人工氣候室里模擬不同海拔高度和覆冰程度綜合作用下合成絕緣子的交流閃絡特性，主要分析海拔高度（即氣壓）和覆冰量對閃絡電壓的影響，並進行閃絡機理分析； 3 ）研究高海拔和覆冰對合成絕緣子憎水性的影響。 -
Exemoo has developed a reputation for excellence in every area of industrial furnace design, construction, and installation. each job whether a small re - brick or the design and construction of a completely new system is individually tailored to the customers specific needs. our engineers are involved in every step of the process and our crews are specially trained to inspect all jobs to ensure the highest level of quality control. exemoo has worked with our french joint venture partner to bring their advanced technology to the products made in our china facility. these products include : double chamber gas or oil quenching vacuum furnace, low pressure vacuum nitriding furnace, high pressure sintering furnace, etc. we have gained iso9001 accreditation with registration number 0205q15647r0s
易西姆公司在吸收法國技術基礎上，在中國實現國際先進的不同類型的真空爐設計與製造，以向中國客戶提供性價比優性能可靠的各種真空爐，並且致力於各種真空爐的銷售設計生產新工藝與新技術的研發，以及自動化生產線設備與工程的總成，在低壓真空滲碳爐真空高壓氣淬爐真空壓力燒結爐，低壓真空滲氮爐，以及真空爐自動化生產線方面，在國內乃至國際上都處于領先地位。 -
Test results show that the ignition process of pc in ignition chamber includes three stages. the effects of velocity, pc concentration and wall temperature on the ignition of pc are studied
試驗結果證實煤粉氣流在感應加熱點火室內的著火過程分為三個階段，揭示了煤粉入口速度、煤粉濃度、點火室壁面溫度對煤粉氣流著火的影響規律。 -
At the appropriate pressure, the chamber is opened to a high-vacuum pumping system that continues to reduce the pressure of the process chamber.
在適當的壓強下，工藝室被接通高真空泵系統抽氣，以繼續降低工藝室的壓強。 -
This paper studies the application of inductively coupled plasma ( icp ) technology to the etching compound semiconductor insb - in film. by means of single probe and double probe, the ion density and electron temperature of chamber ( 30mm and 50mm in height respectively ) under varied process condition were diagnosed. the spatial distribution of the axial position of the two parameters and the varied curve that the two parameters varies with the power and air pressure are obtained
利用單探針和雙探針診斷30mm高反應室和50mm高反應室在各種工藝條件下的離子密度和電子溫度，得到這兩個參數在反應室軸向位置的空間分佈、隨功率和氣壓的變化曲線、頂蓋接地和反應室體積對它們的影響，結果表明離子密度為10 ~ 8 10 ~ （ 10 ） cm ~ （ - 3 ） ，電子溫度在4 10ev之間；當頂蓋接地時，該處的等離子體密度明顯大於不接地；在同樣條件下， 50mm高反應室內的離子密度明顯大於30mm高反應室。 -
Finally, the inlet port and combustion chamber designed and machined is tested on 4100qb. the paper mostly investigates the change of performance targets of the engine that three different grooved chambers including two different re - entrant model and one w model match with various intake port and nozzles, in order to realize the influence of chamber geometry on combustion process. the results analyzed have indicated that re - entrant grooved chambers can enhance the turbulent intension in the chamber, improve the combustion proces of diesel engine on the altiplano, being groove, re - entrant and convex, and have the farther developing potential
著重研究兩種縮口、一種直口矩形環槽燃燒室與不同進氣道、噴油嘴的組合方案發動機的動力性、經濟性及排放指標的變化，確定燃燒室的幾何形狀對燃燒過程的影響。分析結果表明，由於有矩形環槽、燃燒室縮口以及燃燒室底部凸臺，縮口矩形環槽燃燒室中的紊流得以加強，改善了高原柴油機的燃燒過程，這種燃燒室有進一步發展的潛力。 -
The ignition process of emulsified fuel ' s catalytic reforming reaction in constant volume chamber was studied and the ignition curves of diesel oil, emulsified fuel ( containing 20wt % water ) with or without catalyst were compared
摘要為研究乳化油的點火延遲，從實驗和計算兩方面研究了催化重整反應對乳化油著火過程的影響，對比了柴油和摻水量為20 % （質量比）乳化油在有、無催化劑條件下的溫升曲線。 -
Li jun, yoshio sato, akio noda. an experimental study on dme spray characteristics and evaporation process in a high pressure chamber. sae, 2001, 2001 - 01 - 3635
文華，劉永長，魏明銳等.二甲醚和柴油噴霧特性的數值模擬分析.天津:內燃機學報， 2003 （ 4 ） -
It is very difficult to analyze flame radiation in the cylinder of a diesel engine by theoretical method since flame radiation is a function of many parameters, such as the combustion process, the geometrical description of the chamber, the soot formation and oxidation processes, the soot radiant temperature and soot absorption coefficient. the radiant property of the flame in a cylinder is dependent on the combustion process. but the thermodynamic state of real engine cycles can be analyzed from the pressure - volume diagrams in the cylinder. thus a new thermodynamic computational model is set up for the flame radiation in the cylinder of a diesel engine based on the indirect relationship between the flame radiation and the pressure - volume diagram of the combustion process in this paper. the flame radiant heat flux in the cylinder of a di diesel engine is calculated with the variation of crank angle by this model. compared with measured values, the result of the computational values shows the model is available to represent the effects of flame radiation
柴油機缸內的火焰輻射受諸多因素的影響，用理論分析法來確定它是相當困難的，由於柴油機缸內火焰輻射特性依賴于缸內的燃燒過程，而燃燒過程中的實際熱力狀態又可用示功圖來分析，因此藉助於火焰輻射與缸內熱力參數之間的這種間接關系，建立了一種計算柴油機缸內火焰輻射傳熱的新模型，利用該模型對一臺直噴柴油機缸內火焰輻射熱流量隨曲軸轉角的變化情況進行了計算，將計算結果與實測結果進行了比較，表明該模型能較好預測缸內火焰輻射傳熱量。 -
Water steam was used as oxidant, and the optimum water steam partial pressure is between 1 10 - 4 and 5. 5 10 - 4 pa. under the optimum growth parameters, a ceo _ 2 seed layer with highly textured degree was successfully prepared. beside the one step process was experimented in this dissertation, the two step process was proposed and studied to further improve the quality of ceo _ 2 seed layer. in the two step process, about 15 nm thick of ce metal layer was deposited on metallic substrate at the first step, then water steam was introduced in the chamber, and the ceo _ 2 thin films were subsequently deposited with reactive sputtering in the
總結出沉積ceo _ 2薄膜的優化工藝條件，當沉積溫度為720 - 850 、水蒸汽分壓介於1 10 - 4 - 5 . 5 10 - 4pa之間、退火時間40min時，獲得了織構程度良好的ceo _ 2種子層薄膜; 3 .由於一步法制備ceo _ 2種子層中水分壓范圍狹窄，工藝條件難以控制，並且退火延長了薄膜的制備時間，因此，本論文又採用了兩步生長法沉積ceo _ 2種子層，即:先在ni - w基帶上沉積一層約15nm的金屬ce薄膜，再通入氧化氣氛（水蒸汽） ，繼續進行薄膜沉積。 -
The passage dimension of separation chamber, the heating temperature of intake pipe air and the relevant influence of the ceramic heat insulation coating of combustion chamber upon the compressive ignition process of natural gas were studied by experiment
實驗研究了分隔室通道尺寸、進氣管空氣加熱溫度、燃燒室陶瓷隔熱塗層對天然氣壓燃著火過程的相關影響。 -
With the progress of the computer technology, people are beginning to apply the approach that includes the test in laboratory and the numerical simulation to study the process of the flow, the heat transfer and combustion in the chamber
由於爐內換熱過程的復雜性，單純依靠實驗室試驗臺進行研究是很困難的。隨著計算機技術的不斷發展，人們開始尋求用實驗室試驗結合數值模擬的方法來研究爐膛內的流動、傳熱及燃燒過程。 -
The experimental investigations were first conducted on diesel spray wall - impingement mixing process with or without a bump on a flat wall and in a combustion chamber by means of plif method in the self - made constant volume combustion spray simulation set - up which can reproduce the typical working conditions and high - pressure fuel injection of modern diesel engines. the simulation computation of a cfd code about them was then carried out
首先在自行研製的、可以模擬現代柴油機典型工作環境及高壓燃油噴射特性的定容燃燒噴霧模擬裝置上用片狀激光誘導熒光法（ plif ）對平壁上、燃燒室內不設置和設置bump的柴油噴霧撞壁混合過程進行了試驗研究，然後又用cfd多維數值分析軟體對其進行了模擬計算。 -
Three - dimensional numerical simulation of the spray process in swirl chamber with a hybrid breakup model
利用混合破碎模型對渦流室內噴霧過程的三維數值模擬 -
Ionization in a free-air chamber is the standard process for measuring x-and γ-ray exposure.
自由空氣電離室中的電離作用是量度x和射線照射量的標準方法。 -
Ionization in a free-air chamber is the standard process for measuring x-and r-ray exposure(in roentgens).
自由空氣電離室中的電離作用是量度x和r射線照射量（倫琴）的標準方法。 -
In this process the chamber and its furniture grew more and more dignified and luxurious ; the shawl hanging at the window took upon itself the richness of tapestry ; the brass handles of the chest of drawers were as golden knockers ; and the carved bed - posts seemed to have some kinship with the magnificent pillars of solomon s temple
在喝酒的過程中，房間和房間里的傢具變得越來越富麗堂皇窗戶上懸掛的披肩添上了織花帷幔的華貴五斗櫥上的銅把手就像是黃金做成的門環四柱床的雕花床柱，同所羅門廟宇的宏偉廊柱也有了幾分相似。 -
( 1 ) the cfd model for the pulse combustion spray drying process. the computational fluid dynamics ( cfd ) based on the two - phase flow theory was employed in this paper, which used the standard k - e model and the particle trajectory model to simulate the gas - particle flow in the drying chamber. the momentum, heat and mass transfer regarding both gaseous and particulate phases during the spray drying inside the drying chamber was also revealed
為解決這一難題，本文利用氣體一顆粒兩相流理論和計算流體力學（ cfd ）技術，建立了更符合實際噴霧乾燥過程的數學模型即噴霧乾燥的cfd模型，並進行了脈動燃燒噴霧乾燥過程模擬，其主要內容如下： （ 1 ）建立了脈動燃燒噴霧乾燥的cfd模型該數學模型建立在氣體一顆粒兩相流基礎之上，用標準k -模型預測乾燥室內的氣體湍流運動過程，顆粒軌道模型追蹤乾燥室內顆粒群的運動軌跡，熱質傳遞模型描述空氣和液滴的熱質傳遞過程。 -
The results indicate that drying thickness, radiant temperature and pressure of drying chamber are the most three significant factors. there ' s hardly any relationship between freezing rate and drying time, the sublimation drying time of slow freezing material is shorter than quick freezing one, but its desorption drying time is relatively longer, so the total drying time is approximately the same. the initial freezing temperature and freezing manner has little influence on vacuum freeze drying process
試驗表明：凍干厚度、加熱板溫度、系統的真空度是最重要的三個過程參數；凍結速率對總凍干時間沒有影響，慢凍物料的升華乾燥時間要比快凍物料短，但慢凍的解析時間相對較長，兩者的總凍干時間相差很小；初始凍結溫度對凍干過程的影響可以忽略。
分享友人