prototype mould 中文意思是什麼

prototype mould 解釋
試驗模
  • prototype : n. 1. 原型；典型；樣板；模範，標準。2. 試制型式；樣機；樣品；【物理學】原器。
  • mould : n 1 （陰）模 鑄模 模型；外型；鑄型；字模 字型；模製品。2 形狀 性格 氣質；狀況。3 【建築】（裝飾）...
  1. According to the special shape and operate requirements of the torpedo, the structure and moulding process of the torpedo shell are established, in which the body and overlay block with grooves are moulded by fiber winding, and close moulding respectively with the adhesive by limited stop compression. in the light of the selection of raw material system, composite system with outstanding performance are defined, based on which the mechanical properties are tested., with the overall consideration of structural characters and design demands, the main factors which may have effects on the strength and stability ( including stiffness section dimension, stiffeners space, skin thickness and skin lay angle ) is optimized one by one for the structure design parameters on the base of the fem model of skin, stiffness and layover block by fem. as a result, the prototype with 1 : 1 proportion and its structure and lay optimization design are completed. the moulding technology for polyurethane foam moulding the stiffened shell is obtai ned in terms of the design, manufacture moulding, experimental mould and tooling

    依據在研產品特殊的外型結構和使用要求，確定了該型號水雷復合材料殼體的具體結構形式和復合成型工藝路線，即由纖維纏繞工藝成型主體異形件，閉模成型帶通槽外貼塊，用限位加壓工裝實現粘接的工藝路線；通過對原材料體系的篩選，確定了綜合性能較好的復合材料體系，以此為基礎進行了力學性能測試；運用有限元方法，建立了蒙皮、筋條和外貼塊的分析模型，綜合考慮結構特點和設計要求，對影響結構強度與穩定性的主要因素（包括筋截面尺寸、筋間距、蒙皮厚度、蒙皮鋪層角度）分別進行了結構設計參數的優選，最終完成了復合材料異形耐外壓殼體1 : 1樣件和縮比實驗件結構及鋪層優化設計；完成了聚氨酯泡沫胎成型內置加筋殼體的成型工藝技術研究；對縮比件進行外壓性能測試，並給出了應力、應變測試結果。
  2. The application in rapid tooling manufacturing of the resin - infiltrated prototypes is researched. it greatly improved the utilization efficiency of the prototype using this kind of post - treatment prototype directly into manufacturing wax patterns. in addition, these kind of post - treatment patterns have been used to develop the plaster mould and ceramic mould and both have made great progress

    本文就所開發出的滲樹脂成型件在快速模具製造中的應用進行了研究，通過直接利用該類后處理件作為型腔來製造蠟型，並將此蠟型用於熔模鑄造中，極大的提高了原型件的利用率；另外還用此類后處理件進行石膏型和陶瓷型精密鑄造型腔的開發，均取得了較大進展。
  3. Pack all circuits and each part into prototype, examine the rationality of the structure design, experience the product, carry on the last adjustment, reduce the risk of the mould design

    將全部電路和各個零件裝入樣機模型，檢驗結構設計的合理性，體驗設計產品的使用感受，對出現的問題進行最後的調整，降低模具開發的風險。
  4. Applying similarity principle and analyzing one dimensional consolidation, the paper transform the mould to the prototype

    應用相似理論和一維固結理論分析，將室內模型轉化到實際工程當中。
分享友人
分享到 Line

分享到臉書