pull-push-method 中文意思是什麼

pull-push-method 解釋
徒手上弦法
  • pull : vt 1 拉，拖，牽，曳 （opp push）; 勒（馬）。2 拽住；扯破，扯開。3 拔去（雞等的）毛；拔（牙齒、瓶...
  • push : vt 1 推（門等） （opp pull; draw）; 推動（車子等）；刺出（劍、手杖等）。2 大力推進，進行。3 使延...
  • method : n 1 方法，方式；順序。2 （思想、言談上的）條理，規律，秩序。3 【生物學】分類法。4 〈M 〉【戲劇】...
  1. Using the modified method, 6 kinds of tl topologies of single - switch converter are obtained. the deep research reveals that these tl topologies can have less value of the inductor by using interleaving modulation strategy compared with conventional modulation strategy on the condition that the current ripple of the inductor are the same. some drawbacks such as high voltage stress, difficulty of realizing soft - switching, and magnetic aberration were presented in the conventional push - pull converter

    對基本方法進行改進，提出了適合6種單管直流變換器的三電平拓撲變換方法，成功地得到了其三電平拓撲，開關管的電壓應力降為原來的一半；經過對這些三電平拓撲控制策略的深入研究，詳細論述了交錯開關方式可以最大幅度地減小電感的電流脈動，從而可以在電流脈動要求相同的情況下減小電感的設計值。
  2. Full - automatic tyre changer with push - pull horizontal arm and tilt back vertical arm, pneumatic locking, instead of semi - automatic and manual locking method, improve the working efficiency

    此款為全自動推拉臂、后傾式立柱的氣動鎖緊機型，取代了半自動的手動鎖緊的低效率方式。
  3. Employ ip address dynamically mapping method to implement single entry point. the implementation of single control point includes single monitor with pull model and single control with push model. then we put forward hierarchical control structure to implement single control point

    三、採用ip地址動態映射演算法實現單一入口點，減少了處理延時；單一控制點的實現分為單點監控和單點管理兩方面，分別採用pull模型和push模型；並在此基礎上，提出了層次控制結構，充分體現了集群之間的對等關系。
  4. In the automobile type and logistics information publication system, information of automobile type and parts to be assembled can be displayed on terminals set on each station, which enables ship - fitters know the car flow on the assembly line and make preparations for assembly work. the system also allows workers to send out material requirement message so that logistics department could response to the message and deliver the material to right place in proper time and by proper amount, which converts the traditional " push " mode material supply method to demand drive " pull " mode

    本文研究的車型及物流信息發布系統可以在工位實時、動態地顯示總裝線上各工位的車型信息和零件選裝信息，使裝配人員及時了解總裝線車流情況，提前做好裝配準備；允許裝配人員通過鍵盤提交物料需求信息；物料供應部門可以實時響應裝配工位的物料請求，將物料及時、適量地送到合適的位置。
分享友人
分享到 Line

分享到臉書