rigid test 中文意思是什麼

rigid test 解釋
剛性試驗
  • rigid : adj 1 堅硬的，強直的，硬性的，僵硬的 （opp flexible elastic）。2 堅定的，固定不動的。3 嚴格的，嚴...
  • test : n 1 檢驗，檢查；考查；測驗；考試；考驗。2 檢驗用品；試金石；【化學】試藥；（判斷的）標準。3 【化...
  1. Cellular plastics - compression test for rigid materials

    泡沫塑料.硬質材料的壓縮試驗
  2. Establishing an human spine dynamic model is an significan event to study spine injured biomechanics of pilot " s ejective injury, parachute opening, landing and study the endurance to impact loading on human spine. in this paper, the huston " s method of kane " s equations is developed so that it can be applied to the multibodysystem including translation between the bodyies. the dynamic model of human spine is provided basing on these theories, while the big movement of spine is considered. the deformation of vetebra is far smaller comparing with the intervetebra disc, so the spine is considered into multibodysystem including rigid bodies ( vetebra ) and the flexible bodies ( intervetebra disc ). the computer solution correspond with the results of the large scale human impact test. the rigid coefficient factors and the damping factor of intervetebra joints are obtained

    人體脊柱動力學模型的建立對研究飛行員彈射救生、傘兵跳傘開傘、著陸等脊柱損傷的生物力學以及研究人體脊柱耐受沖擊載荷的極限問題都具有重要意義.首先發展了凱恩方程的休斯頓方法，使其可應用於變形體連接的多體系統，並以此理論為依據建立人體整椎脊柱沖擊動力學模型，此時考慮脊柱的大位移運動，每個椎骨的變形相對椎間盤的變形小得多，把脊柱看成由剛體（椎骨）和變形體（椎間盤）組成的多體系統.並以大型真人坐姿沖擊實驗結果進行了擬合，最後得到腰椎間關節剛度系數因子和阻尼系數因子
  3. Test method for tumbling friability of rigid cellular plastics

    硬質泡沫塑料滾動磨損試驗方法
  4. Standard test method for measurement of hydraulic conductivity of porous material using a rigid - wall, compaction - mold permeameter

    使用剛性壁壓縮模式磁導率計測量多孔性材料液壓導電率的標準試驗方法
  5. Static and dynamic test of open spandrel rigid - framed arch bridge under vehicle loading

    空腹式剛架拱橋的車輛荷載靜動力試驗
  6. Three - dimensional photoelastic test of beam - arch joint of open spandrel rigid - frame arch bridge

    空腹式剛架拱橋梁拱節點三維光彈性試驗研究
  7. Standard test method for impact resistance of flat, rigid plastic specimens by means of a falling dart tup or falling mass

    用下落投擲法測試平板剛性塑料樣品的抗沖擊性的標準試驗方法
  8. Test study on distribution of base pressure of rigid pipe on flat soil foundation

    平面土基剛性圓管基底壓力分佈的試驗研究
  9. The best percentages of the component parts of the new material was found in the experiments. we measured its mechanical properties and did the test on its stableness. the results of the experiments and analysis show that the semi - rigid bituminous emulsion has advantage to the bitulith

    本文對乳化渣油半剛性路面材料進行了系統的實驗研究和理論分析，簡述了該材料的製作和成型機理，探討了其最佳配比，進行了穩定試驗，測試了力學性能，並對其進行了微觀分析。
  10. Test method for flammability of rigid cellular plastics - vertical burning method

    硬泡沫塑料燃燒性能試驗方法垂直燃燒法
  11. By means of laboratory and field experimentation of typical semi - rigid base materials, the relationships among laboratory experimental values, field maintain values, field core values and construction criteria are put forward. and the relationships between different test methods are established. using time - temperature conversion principle, it processes the intensity assessment of field cores, then offers the method of determining the test deflection of pavement surface

    通過典型半剛性基層材料的室內外試驗，研究主要設計參數的室內試驗值、野外養生值、現場取芯值及施工指標間的關系，建立了不同試驗方法間的相關關系，運用時溫換演算法則，對現場芯樣進行強度評定，並提出了路表彎沉檢測標準的確定方法。
  12. Test method for flatwise flexural impact resistance of rigid plastics

    硬塑料耐平地軟沖擊試驗方法
  13. Standard test method for flatwise flexural impact resistance of rigid plastics

    硬質塑料耐平面柔性沖擊性的標準試驗方法
  14. Test method for compression of rigid cellular plastics

    硬質泡沫塑料壓縮試驗方法
  15. Test method for bending of rigid cellular plastics

    硬質泡沫塑料彎曲試驗方法
  16. Testing of rigid cellular materials ; flexural test

    硬泡沫材料檢驗.抗彎試驗
  17. Cellular plastics, rigid - test methods for self - skinned high - density materials

    硬質泡沫塑料.自結皮高密度材料的試驗方法
  18. En iso 9054 cellular plastics, rigid. test methods for self - skinned, high density materials

    硬質泡沫塑料.自結皮高密度材料試驗方法
  19. And the displacement control of the leaf spring center was transferred to the displacement at load point. then after the load step options configuration, the leaf spring stress circulation under cycle loadings was calculated. the model was validated by the result compare between the rigid extracted from the simulation results and the one out of the rigid test of the leaf spring

    使用加載頭和簧片的接觸行為來模擬加載狀況，並將對簧片中心的變形控制轉換為對加載點的位移約束，然後利用載荷步選項配置完成一個載荷循環，由此計算出加載階段下鋼板彈簧內部的應力循環。
  20. Adhesives - peel test for a flexible - bonded - to - rigid test specimen assembly - 90 peel

    膠粘劑.軟料與硬料粘合試樣組件剝離試驗. 90剝離
分享友人
分享到 Line

分享到臉書