rolling velocity 中文意思是什麼

rolling velocity 解釋
滾動速度
  • rolling : adj 1 旋轉的；滾動的；波動的，起伏的；滔滔地流的；隆隆響的。2 捲起的。3 左右搖擺的。4 〈美國〉起...
  • velocity : n. 1. 迅速；快速。2. 速度，速率。3. 周轉率。
  1. The velocity field has been designed in this article on defect of rolling workpiece surface about cross wedge rolling technique in the process of forming axial symmetry spare parts by result of simulated experiment of consult document [ 4 ]

    摘要依據文獻[ 4 ]的模擬實驗結果，擬定了楔橫軋工藝成形階梯軸類件時軋件表面出現表面缺陷（蛇皮狀或魚鱗狀缺陷）時的金屬流動速度場。
  2. In view of this situation this article has conducted research to the design of metallurgy auxiliary biography with the frequency conversion table electrical machinery first multianalysis to the frequency changer and the frequency conversion table electrical machinery movement characteristic is carried out, the voltage waveform harmonious which the frequency changer outputs is big, attacks in a big way, and the voltage climbing rate reaches as high as 6600v / mu s which is 20 times ordinary sine alternating voltage, the rolling mill auxiliary biography table set the extremely strict request to the electrical machinery ; its movement frequency is very low, rate frequency in 8 - 20hz ; the velocity modulation scope is wide, the lowest movement frequency lowers to 1hz, and the starting number of times is quite frequently, each hour reaches as high as 600 - 800 time, the impact shoulders in a big way, the overload capacity request is high

    針對這一情況本文對冶金輔傳用變頻輥道電機的設計進行了系統研究。首先對變頻器和變頻輥道電機的運行特性進行詳細分析，變頻器輸出的電壓波形諧波大，沖擊大，電壓上升率高達6600v / s ，是普通正弦交流電壓的20倍;軋機輔傳輥道對電機提出了十分嚴格的要求:其運行頻率很低，額定頻率在8 - 20hz ;調速范圍寬，最低運行頻率低到0 . 5hz ，起動次數相當頻繁，每小時高達600 - 800次，沖擊負荷大，過載能力要求較高。
  3. Acceleration, for instance, will be offset by air resistance and rolling friction, instead of a " max velocity. " robots crashing into the side of another robot will push it sideways, based on laws of friction and a semi - elastic collision

    例如，加速度將會被空氣阻力和滾動摩擦力抵消一部分，而不只受到「最大速率」的限制。根據摩擦力和半彈性碰撞原理，機器人撞到另一個機器人的一側時會把它推到一邊去。
  4. Analytical study on lubrication states and velocity in aluminum foil rolling process

    冷連軋機成品板面粗糙度控制技術的研究
  5. Rolling bearings. deep groove ball bearing vibration velocity. specifications

    滾動軸承.深溝球軸承振動速度技術條件
  6. Abstract : based on the mathematical models of roll speed for cross - rolling elongation process, the effects of toe angle on roll speed, local feed angle and local angular velocity, and also on material flow are analyzed. by the analysis, the toe angle can be optimized

    文摘:基於建立的斜軋延伸機軋輥速度模型，模擬分析了沿軋制方向和螺旋方向上輾軋角對軋輥速度、局部送進角、局部角速度的影響，進而分析了這些參數對金屬變形和流動的影響，據此可優化輾軋角。
  7. Evaluation on vibration velocity of rolling bearings

    滾動軸承振動速度的評估
  8. Rolling bearing. measuring methods for vibration velocity

    滾動軸承.振動速度測量方法
  9. Rolling bearings. specifications of vibration velocity for tapered roller bearings

    滾動軸承.圓錐滾子軸承振動速度技術條件
  10. Larger rolling velocity gives better materials filling in the ring section contour

    同時發現，軋制速率影響環件軋制的成形性能，較大的軋制速率有利於環件輪廓填充。
  11. The results show that improving the rolling velocity and reducing the galvanizing time will result in reduction of strength loss after galvanizing, and increase of bend torsion valve, thus productivity is improved

    結果表明：提高收線速度，減少浸鋅時間，鍍后強度損失減小，彎扭值提高，生產效率提高。
  12. The paper got the detailed results that how the change of the structural parameters and the soil parameters joining in vibration influence the stability and walking velocity of the system. meanwhile, the paper got the optimal structural and run - time parameters, and acquired the main factors limiting walking speed of rolling tamper and their optimal values

    通過大量的模擬，得出了模型的結構參數以及土壤參振參數的變化對系統穩定性、行走速度影響的具體結果，得到了較為優化的結構參數和運行參數，從而找出了影響滾壓夯行走速度的主要因素及其最優值。
  13. . rolling bearings. specifications of vibration velocity for cylindrical roller bearings

    滾動軸承.圓柱滾子軸承振動
分享友人
分享到 Line

分享到臉書