roughcast 中文意思是什麼
roughcast
解釋
vt. 及物動詞 ,n. 名詞 【建築】粗作，粗製；粗塗，打底子；打底用灰泥；（擬定）大體方案。-
Design of hot extrusion mould of roughcast of multi - joint thin - wall brazen valve body
多接頭薄壁銅閥體毛坯熱擠壓模設計 -
The primary problem in using the method of numerical control manufacture - shot peen forming to manufacture the part on rough is to determine the size of the roughcast
採用毛坯數控加工-噴丸成形方法的首要問題是確定坯料結構尺寸。 -
Research on design principles and methods of blisk manufacture roughcast
整體葉盤製造毛坯設計原則與設計方法研究 -
A swift rose soundlessly over the slate roof and the heat shimmered on the roughcast walls
他們躺下來，遞過水瓶，旅行包仍背在背後。 -
On the basis of our previous forging equipment, our company has purchased another fast forging hydraulic equipment of 250 tons, with which we can forge various roughcast of special sections below 20 tons, as well as heat
我公司在原有的鍛打設備外，又購進一臺250噸的快速鍛打液壓設備，可?根據客戶要求鍛造20噸以下的各種異型鋼材毛坯，還可?客戶提供退火正火回火淬火等熱處理服務。 -
The simulations of the blank forming process is always a very pop question in the domain of plasticity forming. it has very important significance as to making certain the figure of the blank roughcast calculating strain and stress, establishing reasonable forming craft and designing mold
板料成形過程模擬一直是塑性成形領域研究的熱點問題，對于確定板料毛坯形狀、計算應力、應變分佈、制訂合理的成形工藝和模具設計有重要的意義。 -
Forging hammer is an important device, which is used to forge roughcast in machine shops. when forging hammer works, violent vibration produces, so the precise instruments and equipment around ca n ' t run normally, the stability and longevity of the workshop structure may lower, furthermore, the health of people hurts. the damping to forging hammer foundation is all through the ages a hot question for discussion
鍛錘是機械工廠中一種對毛坯進行鍛造加工的重要設備，但鍛錘工作時產生的極大振動，不僅嚴重影響周圍精密儀器、設備正常運行，降低廠房建築結構的穩定性及其使用壽命，而且是一種危害人體健康的工業公害，因而鍛錘隔振歷來是一個熱門研究課題。 -
This paper focuses on the core part of the il & sm fixture system - information process system ( ips ). after relevant information is obtained from the current part, ips designs the roughcast and the parameters of stuffing, matches or designs rational locating box, positions all the locating bolt, finishes the procedure of datum conversion and ensures the communications between state shaping system, part fixing system and nc programming system
本文的研究對象為il & sm夾具系統的核心部分? ?信息處理系統（ informationprocessingsystem ? ips ） ，它通過獲取零件的相關信息，進行毛坯與填料厚度的設計，設計或配置出合理的尋位箱，智能布置尋位元件，完成基準轉換，並負責與狀態成型系統、工件安裝系統、 nc編程系統等模塊的通訊。
分享友人