signal interruption 中文意思是什麼
signal interruption
解釋
信號中斷- signal : n 1 信號，暗號；信號器。2 動機，導火線 （for）。3 預兆，徵象。adj 1 暗號的，作信號用的。2 顯著的...
- interruption : n. 1. 打斷；中斷；停止。2. 斷絕，斷路。3. 插話，打岔。4. 障礙物，遮斷物。5. 中斷期，休止期。
-
And the solutions of the three problems above are discussed : the solution to the simulcast interfering which is caused by the simulcast delay spread ( sds ) and the zero - beating is given in chapter four. based on the well understanding of the principle of ms - i / h / 0 in ipnp, the examples are given in chapter five on how to solve the problem of communication interruption between paging zones. through the analyse of signal switching between chengdu and deyang, the synchronization error between flex frames, and the bug in the multi - frequency roaming principle are pointed out
通過以上分析，文章探討了對上述三個問題的解決： ?對同播干擾問題，分別分析了時延差和零拍頻所造成同播干擾的客觀存在，探討了系統設計和網路優化的基本方法； ?對ipnp聯網障礙，提出了在掌握ipnp對各pncc作為輸入局歸屬局?輸出局（ ms ? i h o ）的靈活定義、以及相關參數配置原理的基礎上，分析聯網障礙的思路； ?對信號切換障礙，以成都和德陽兩地的局部廣域覆蓋為例，分析了flex幀失步和flex多頻漫遊原理設計缺陷的客觀存在，並探討了相關的解決方法和建議。 -
This system ' s hardware adopts dsp - embedded controller, which can process digital signal independently. the controller communicates with pc by accessing memory. on the side of controller, c language is used to write the interpolation program and the interruption service program, while on the side of pc, visual c + + is used to write programs in which functions of editing nc - code, real - time control and human - machine interaction interface is fulfilled
該數控系統的硬體採用了具有獨立數字信號處理功能的dsp型運動控制器，控制器通過內存訪問與pc機通信，使用c語言編寫了控制器端的中斷服務和插補程序，使用visualc + +編寫了pc端的數控代碼編輯、實時控制和人機交互界面程序。 -
When the light wavelength permeating the f - p filter equals to the bragg reflection wavelength, there is an interrupt request signal, dsp deals with the useful information after dsp answers interruption, and then obtain the corresponding changes of the measured parameters
當透過f - p濾波器的光波長與bragg反射波長重合時，就產生中斷請求信號， dsp響應中斷后就對有用的信息進行處理，進而得到相應被測參量的變化。 -
In the designation of software, the author adopts the modular designing method, and makes full use of the functions what the mcu offers, such as a / d function, interrupt function, pwm function, and software timer function. as a result, the following subroutines are programmed : a / d sample, read optic - electron coder signal, disposition of orientation interruption, z interruption, and software timer
在控制軟體的設計上，採用模塊化程序設計方法，充分利用單片機內部提供的a d功能、中斷功能、 pwm功能、軟體定時器等功能，設計出了a d采樣子程序、讀編碼器信號子程序、定位中斷服務子程序、 z中斷服務子程序、軟體定時器中斷服務子程序等模塊化程序。 -
Especially it allows various types of interruptions of external digital input, timer output and a / d conversion, each type of interruption has its own role in the signal measurement or in exact pace control, its fifo buffer function makes it possible to work at the sampling rate of 200k samples per second without carrying over - burden interruption rate, its latch type external interrupt request along with its high frequency clock makes a precise locating of pulse edges possible
該控制系統在工作過程中，有多種產生於不同部件的信號需要檢測，其中有模擬輸入信號十三路，數字輸入信號三路，通過數據採集和信號分析，判斷該控制系統工作是否正常。結合系統檢測的具體要求，本論文從硬體設計和軟體設計兩個方面，實現了數據採集系統的硬體介面電路和軟體演算法。 -
This paper projects a utility subdividing drive system of step motor, which consists of digital control module, drive module and power module, it uses at89c52 single chip processor as the core, it realizes the external event or generates control signal by i / o interface, timer and external interruption, the system introduce pld device and isp technology to the design of phase sequencer, it simplified circuit and improved the anti - disturbing capability by using abel - hdl language, this system can realizes data memory, velocity digital control and led display, etc. this paper adopted firstly the single - chip technique to design control system, which replaced old complicated logic control circuit and simplified test process
本文研究了一種實用的步進電機細分驅動系統，由數字控制模塊、驅動模塊和電源模塊組成，系統以at89c52單片機為核心，通過單片機的i o口、定時器計數器中斷來實現外部事件監控以及控制信號的產生，系統將可編程邏輯器件（ pld ）器件和在系統編程（ isp ）新技術引入到細分驅動環行分配器的設計，通過abel _ hdl語言編程實現硬體軟化設計和邏輯重構，大大簡化了電路，並提高了電路抗干擾能力。使系統實現參數存儲，速度數字控制，數碼顯示，進退刀控制等功能。
分享友人