simulation analysis 中文意思是什麼

simulation analysis 解釋
模擬分析
  • simulation : n. 假裝；模擬；裝病，裝瘋；【生物學】擬態，擬色。
  • analysis : n. （pl. -ses ）1. 分解，分析；【數學】解析。2. 梗概，要略。3. 〈美國〉用精神分析法治療（＝ psychoanalysis）。
  1. Depend on the comprehensive analysis and study of the structure, principle, and exterior characteristic of the motor, through the methods of system modeling and digital simulation analysis, two kind of control device that work for the low voltage ( lvdc ) and the high voltage ( hvdc ) in avigation are researched respectively. point to the control technique of close - loop speed stabilization at a limited adjustment speed range, we bring out the close - loop speed control method that using the rotor position sensor indirectly measure the speed of the motor

    在全面分析了稀土永磁無刷直流電動機的結構特點、工作原理、運行方式以及外部特性的基礎上，通過系統建模和數字模擬分析，分別針對航空低壓直流（ lvdc ）和高壓直流（ hvdc ）兩種電動機構用永磁無刷電動機，在小范圍轉速連續調節下的閉環穩速控制技術進行了詳細理論研究，提出了利用轉子位置傳感器信號間接測量電機轉速進行電機轉速閉環穩速控制的策略。
  2. Being aimed to the irrationality and inadaptability of different calculation methods for wide cantilever plate, study of space numeric simulation analysis about concrete box bridge cantilever plate can be carried out for three dimension solids based on ansys

    摘要針對混凝土箱梁懸臂板諸多演算法的不合理性，應用大型通用有限元分析軟體ansys ，以三維實體單元對混凝土箱梁懸臂板進行空間數值模擬分析研究。
  3. Simulation analysis of the lengthways warp of truck carling outside board

    卡車縱梁外板縱向翹曲的模擬分析
  4. Chaotic measured circuit of constant current and simulation analysis

    恆流式混沌測量電路及其模擬分析
  5. Contrarily, numerical simulation & analysis is able to overcome these problems

    而採用數值模擬技術則可以相對避免解析方法的不足。
  6. Confidence percentile estimation to cost and schedule integration based on monte carlo multiple simulation analysis technique

    多重模擬的費用與進度聯合置信估計
  7. Digital simulation analysis of ferroresonance of electromagnetic potential transformer based on matlab

    鐵磁諧振數字模擬分析
  8. Rudimental network centric warfare model and simulation analysis

    一個初步的網路中心戰模型及模擬分析
  9. Crash simulation analysis for sedan car ' s tubular frame bodywork

    管架式轎車車身碰撞模擬分析
  10. Dynamic simulation analysis for portable weighbridge

    便攜式軌道衡動力學模擬分析
  11. Study on fuzzy control strategy and simulation analysis of automotive wet clutch

    汽車濕式離合器模糊控制策略研究及模擬
  12. Simulation analysis of contact position of drill stem and application of antiwear tool

    鉆柱接觸位置與防磨工具的應用模擬分析
  13. Simulation analysis of elastoplastic fem for stability of bedding rock cutting slope

    順層巖體路塹邊坡穩定性的彈塑性有限元模擬分析
  14. Simulation analysis of bullwhip effect

    的數字模擬分析
  15. The main research is below : ( 1 ) the influence to intensity and rigid with corner angle ( 60, 75 and 90 degree ) of crack and the board axes ( 2 ) do a fem stress / strain and crack growth simulation analysis when the corner angle of crack and the board axes is 60 degree ( 3 ) do a intensity resume analysis for the structure which is repaired with a titanium patch in a mechanical way when the corner angle of crack and the board axes is 60 degree through simulation analysis for three failure criterion, we have : ( 1 ) in 60, damage extend quickly with damage analysis in hashin criterion ; it is slower for analysis in maximum stress or hashin - rotem criterion. ( 2 ) in special term ( physical condition incision, shape or maximum load ) the compression strength of the stiffened plate will decline 45 % ~ 50 % under compression loads

    通過採用三個不同損傷判據的數值模擬模擬，得到如下結論： （ 1 ）在60時，用hashin判據進行的損傷分析，損傷擴展較快；最大應力及hashin - rotem判據進行的損傷分析，損傷擴展基本相當，且較慢； （ 2 ）在所給加筋板的物理條件、切口大小及形狀、最大載荷等一定的條件下，該加筋板在壓縮載荷作用下，其壓縮強度下降了45 50 ； （ 3 ）在本文提及到的機械連接修理方法以及載荷條件下，修理后的結構強度恢復能夠滿足戰時要求。
  16. Through the frontal impact test of full size minibus and computer simulation analysis, a parameterized model is set up for the design of body structure crashworthiness in frontal impact during concept design phase, with the modeling techniques well expounded

    摘要選取某微型客車為研究對象，通過實車正面碰撞試驗和計算機模擬分析，建立了用於概念設計階段的面向微型客車車身結構正面抗撞性設計的參數化模型，闡述了建立模型的建模技術。
  17. Simulation analysis of four towers flow in methanol distillation process

    甲醇四塔精餾過程模擬分析
  18. And simulation analysis was made on the influences of the young ' s modules in the two main directions upon the hole - edge stress

    並對兩個主方向的楊氏模量的變化對孔邊應力的影響進行模擬分析。
  19. Numerical simulation analysis on extrusion molding of rings of tapered roller bearings

    圓錐滾子軸承套圈擠壓成形數值模擬分析
  20. Simulation analysis and application of the faults stress field

    斷裂應力場模擬分析與應用
分享友人
分享到 Line

分享到臉書