slow cooling 中文意思是什麼
slow cooling
解釋
緩冷-
The welding performance of homemade wear - resistant cast steel has been studied base on the weldability tests, the repair welding procedures of wean - resistant cast steel ( abrasion - plates ) have been made up, the results show that satisfying repair welding quality can be attained with such welding conditions as the low hydrogenous alkalescent welding rod, preheating and slow cooling, strictly maintaining the interbedded temperature of 250 ~ 300 and controlling welding technique
通過對其焊接性能的試驗研究，制定了該類鑄鋼件（磨耗板）的補焊工藝：低氫型堿性焊條，預熱與緩冷相結合的工藝措施，嚴格控制層間溫度（ 250 ~ 300 ）及焊接工藝規范，可獲得滿意的修復質量。 -
Slow cooling section is next the fast cooling section, cooling tiles slowly by exchange heat between hot gas in the tunnel and the environment air, which is sucked into pipes stick in the tunnel and been heated there, and been sent to dryer to dry biscuits
緩冷段不直接打冷卻風，它通過抽熱風機將環境空氣吸入，進入窯內導熱良好的鋼管，並將換熱后的熱空氣送入乾燥窯內，冷空氣在換熱過程中，使製品得到間接的冷卻，讓製品安全度過573的晶型轉換階段。 -
The tbzre glass has great forming ability, which can form glassy body under relative slow cooling ratio. moreover, the technique of glass ' s annealing is easy. the npre - 1 glass has strong viscosity
其中亞碲酸鹽玻璃（ tbzre ）成玻能力強，在較慢的冷卻速率下也能得到非晶玻璃；且退火工藝簡單，退火溫度下保持一小時后再冷卻到室溫即可。 -
Abstract : the defects such as inclusion, splitting, dislocation and dendrite in the pbxla1 - x ( zry tiz sn1 - y - z ) o3 ( plzst ) single crystal grown from pbo - pbf2 flux by the slow cooling self - seeding technique were discussed in this paper. the forming mechanism of these defects were analyzed and some measures to eliminate the defects were proposed
文摘:本文介紹了助熔劑緩慢降溫自發成核法生長的稀土摻雜鋯鈦錫酸鉛鑭（ plzst ）晶體中出現的幾種缺陷：包裹體、開裂、位錯、枝晶，分析了這些缺陷的形成機理並提出了減少和消除這些缺陷的一些措施。 -
Within several hundreds or thousands of years after the start of a typical warm period, the climate reverted to slow cooling followed by quick cooling over as short a time as a century
典型暖期開始后的數百年至數千年內，氣候先緩慢轉冷，接著在一世紀左右的短期內迅速冷卻。 -
Bell type furnace is mainly used to steel strips, steel plantes, copper strips, copper plates and other metal parts for bright anneal and normal anneal heat treatments. according to the technics, the process of preevacuation. heating, protecting atmosphere gew or non oxidation heating, air cooling, fast colling and slow cooling treaments can be executed
罩式爐主要是用於鋼帶、鋼盤圓、銅帶、銅盤圓及其它金屬材料及零件的光亮退火和一般退火工藝，根據熱處理工藝的要求，可對熱處理工件進行預抽真空、加熱、保護氣氛少無氧化加熱、空冷、快冷及緩冷處理。 -
Because of the effect of sip porous skeleton, the primary si and the eutectic si were separated on the surface of sip porous skeleton under slow cooling conditions, and there were no typical eutectic microstructures in the al - alloys phase of the composites. 6
處于si相顆粒間隙的過共晶al - si合金液在緩慢冷卻凝固時，初晶si和共晶si會附著在si多孔體骨架上析出，在最終的復合材料中沒有典型的al - si共晶組織。 -
The samples that annealed at different temperatures and different cooling ways ( fast or slow ), separately, was compared. the experimental results showed that the temperature and the cooling - way of the gettering process were very important for the gettering efficiency
之後二極體分別進行退火溫度700 6hr 、 800 6hr 、 900 6hr和退火后快、慢降溫方式下j _ r值的比較，結果表明吸除熱處理摘要abstraer溫度對于吸雜效果至關重要。 -
Most rf energy delivery devices, however, have slow coverage rates, need aggressive cooling, or require a lengthy patient preparation that includes local anesthesia due to significant pain
然而，大多數射頻（ rf ）能量輸送器有下述缺點：覆蓋速率緩慢、需要積極冷卻、或需要長時間的病人準備，包括劇痛而要局部麻醉。 -
Thus, an optimized gettering process obtained was 800 and following a slow cooling
氦微孔吸除熱處理合適溫度條件是800 ，冷卻條件是慢降溫方式。 -
The efficiency and the homogeneity of cavities gettering were analyzed by measuring the leakage - current for the diodes in a wafer, which was thermally treated at the optimal condition, that is 700 1hr, then 800 6hr and slow cooling down
第二階段，氦微孔吸雜效果的研究。採用做有二極體的大矽片在700 lhr + 800 6hr + 』漫降溫的熱處理條件下對微孔吸雜的效率、均勻性進行實驗。
分享友人