static mechanical strength 中文意思是什麼

static mechanical strength 解釋
靜態機械強度
  • static : adj 1 靜止的，靜態的，靜力的。2 【物理學】天電的，靜電的。3 【無線電】靜態特性。4 固定的，不活潑...
  • mechanical : adj 1 機械的；機械制的。2 機械學的，力學的；物理上的（opp chemical）。3 機工的，技工的；自動的；...
  • strength : n. 1. 力，力量，體力。2. 強度，濃度；長處；（要塞等的）抵抗力。3. 實力；兵力；全體人數，額定人數，編制。4. 筆力；文勢。5. （證券等的）市價堅挺。6. 〈美俚〉（可能有的）利潤。
  1. By optimizing the parameters such as the additive quantity of corn straw fibre, the content of amylum, the dosage of vesicant, the selecting of accessorial material, and the temperature of frothing, the cushion packaging material that has decompounding capability was prepared, and the factors influencing the mechanical strength of this material was analyzed by the method of static compress test

    通過對玉米秸稈纖維添加量、澱粉含量、發泡劑用量、輔料選擇、發泡溫度等參數的優化，實驗制備了具有可降解性能的緩沖包裝材料，並利用靜態壓縮實驗方法對該材料力學強度的影響因素進行了分析。
  2. The results indicate that if the value of press stress is over certain figure, press stress and al plate ’ s thickness have little influence on sawtooth distortion for the same kind of sawtooth ; sawtooth distortion is well - regulated under static press, while it is irregular under impact press. bottom coating make great influence on bond strength of samples which can improve the value remarkably ; bonding mechanism of clad steel is mechanism of mechanical effect that sawtooth which is hooked occludes with al plate

    結果表明：同種齒型，當壓應力大於一定的值時，壓應力和覆板的厚度對齒形的變化影響不大；靜壓下齒形變化比較規則，鋸齒頂端向一側彎曲成鉤狀；沖壓下齒形比較凌亂，鋸齒的頂端沒有明顯的變形；后處理對試樣的結合強度影響很大，打底試樣由於粘結層的作用，結合強度較高；機械作用機制是復合鋼板的主要復合機理，鋸齒彎曲成鉤狀和鋁板形成機械咬合。
  3. An experimental program which includes lots of unidirectional laminae is conducted using t300 / bmp - 316 material for researching the static and fatigue behaviour of the unidirectional ply. the experimental research for mechanical behaviour of a unidirectional lamina is to set up expressions of the normalized fatigue life, the residual strength degradation and the residual stiffness degradation of a unidirectional ply in the longitudinal, transverse and in - plane - shear directions, which also verifies the fact of nonlinear shear stress - strain behavior of a unidirectional ply in the 1 - 2 planes

    其中:分別對材料t300 / bmp - 316單向層合板縱向、橫向及面內剪切靜載力學性能及疲勞特性進行了試驗研究，並採用最小二乘法擬合得到各主方向正則化疲勞壽命表達式，以及單層板各主方向疲勞加載剩餘剛度退化表達式及剩餘強度退化表達式;試驗同時驗證了單向層合板1 - 2面上明顯的剪切應力應變非線性關系。
  4. The fatigue properties of sucker sods are predicted by its static properties with fatigue strength theory and cumulative damage theory according to the measurement result of conventional mechanical properties of sucker sods with different service periods

    摘要應用疲勞強度理論和累積損傷理論，利用對使用不同年限抽油桿的常規機械性能的測試結果，由抽油桿的靜特性去推測其疲勞特性。
  5. High mechanical strength, it can stand heavy dynamic and static load. it is used in high load capacities and low speed with rotational, oscillating or frequent stop - start motion

    機械強度大，能承受較大的動、靜載荷。適用於高載低速下的旋轉運動，搖擺運動及經常在載荷下啟閉頻繁而不易形成流體動力潤滑的結合。
  6. Conveyor belts - determination of strength of mechanical fastening - static test method

    輸送帶機械接頭強度的測定靜態試驗方法
  7. Conveyor belts - determination of strength of mechanical fastenings - static test method

    傳送帶.機械緊固件的強度測定.靜態試驗法
  8. Iso 1120 : conveyor belts - determination of strength of mechanical fastenings - static test method iso 1120 : 2002 ; german version en iso 1120 : 2002

    傳送帶.機械緊固件強度測定.靜態試驗方法
分享友人
分享到 Line

分享到臉書