steady load 中文意思是什麼
steady load
解釋
不變負荷-
The paper mainly consider the followings : the performance parameter determination of cryopump, heat load determination and heat transfer of large cryopanel, reasonable distribution of heat load, the condition for construct steady flow in small vertical circle pipeline, balance condition for gas and liquid two - phase flow in the connection pipe between cryopanel and dewar, the safety of cryopump
文中探討了低溫泵性能參數的確定；大抽速低溫抽氣面的熱負載的確定及合理分配；冷凝面上豎直圓管內受熱建立穩定流動的條件；冷凝面與杜瓦間的連接管道內氣液「雙相流動」的平衡條件；低溫泵系統運行的安全問題。 -
Presents the steady - state programming with constant coolant average temperature and constant live steam pressure, an ideal programming for marine nuclear power plant ( npp ), under which, both the coolant average temperature and the live steam pressure of nuclear steam supply system ( nsss ) are constant when the steady state operating condition is varied, and points out that in comparison with the steadysate programming with constant coolant average temperature, the ideal programming can improve the overall operating performance of npp effectively, especially in low - load range, for instance, raise the heat efficiency of npp, decrease the operating noise of main coolant pump, and improve the conditions of design, operation and control of the secondary loop system
雙恆定運行方案是船用壓水堆核動力裝置的理想運行方案.在這種運行方案下，當裝置穩態功率變化時，冷卻劑平均溫度與蒸汽壓都保持不變，與通常採用的冷卻劑平均溫度恆定運行方案相比，有效地改善了核動力裝置的總體運行性能，特別是在低負荷運行時，可以提高裝置經濟性、降低主泵運行噪聲、改善二迴路系統的設計、運行和控制條件，這對于提高船用核動力裝置的運行可靠性和安全性具有實際意義 -
Prospect dtzziii series weight - load controller sensor part adopt bridge - type strain piece sensor, and applies steady installation technology to insure sensors running steady and long - range. we provide multi - kinds of sensor installation method. sensor can be installed under the car bottom, on elevator rope hitch plate, on car top wheel and axle and car top beam to work together with controller
前景dtzziii系列稱重控制儀的稱重傳感器部分採用橋式應變片傳感器，應用平穩安裝技術確保長期穩定運行稱重傳感器提供多種安裝方式，可以安裝于活轎底電梯的轎廂轎底電梯繩頭板處電梯轎頂輪軸處電梯轎頂橫樑上面等，與控制儀配合使用。 -
In order to deal with it, the concept of limit load under steady working conditions is put forward. it is a feasible alternative method
本文提出了串並聯逆變器穩態運行重載極限的概念，它是研究啟動極限工況的一種替代方法。 -
No - load steady - state voltage building of a - connected three - phase induction generator under single - phase operation
三角接法三相異步發電機單相空載穩態建壓 -
The trailer adopts whole steel structure and have a kit like, the structure be firm, the shape be beautiful and make to move credibility, use safety, drive steady, load potential big, maintain a maintenance convenience, through long enduring etc. advantage, gather farmland homework and highway to transport at the whole body, the good tool for the plain, mountain area
我公司生產的拖車採用全鋼結構，具有配套性好、結構牢固、造型美觀、制動可靠、使用安全、行駛平穩、裝載潛力大，保養維護方便、經久耐用等優點，集農田作業和公路運輸於一身，是平原、山區致富的好工具。 -
The transformer that use solid state relay to realize automated regulation is explored in this issues, it change the winding turn of once side according to the voltage of second side by on - load tap - changer. thus the purpose to realize automatic steady voltage
本課題研製的應用固態繼電器實現的有載自動調壓變壓器，通過自動有載調壓分接開關根據變壓器二次側的電壓自動改變變壓器一次側的匝數，從而實現自動穩壓的目的。 -
By means of the multi - loop method, the steady - state analysis of internal faults in stator windings of synchronous machine has been made, but as to the transient analysis, research only limited to single machine with no - load
運用多迴路方法，已經基本解決了同步電機內部故障的穩態分析問題，但對故障的暫態研究，以前還僅限於單機空載的情況。 -
The inverted pwm changing electric current the technique is applied in the prototype model. the prototype model was tested and operated on spot, power factor could reach beyond 0. 95, the effect of following modulating voltage was better, the curve of factor of modulated voltage of exchanging systems changed following load rate was linear, the output of wave form was a flat and steady sinusoidal wave
樣機採用了逆變式pwm變流技術，對其進行了現場測試與試運行，測試結果是電網側的功率因數可達0 . 95以上，跟蹤調壓效果良好，變流系統輸出調壓系數（ k ）隨負載率（ p ）的變化曲線基本滿足直線關系，輸出波形呈平滑穩定的正弦波。 -
This dissertation was working for forming a methodology about the advancing analysis of the steady - state voltage stability of power system and the preventive control measures against it, based on the load power forecast technique
本論文致力於研究基於負荷預測技術的電力系統靜態電壓穩定的預測分析與預防控制方法。 -
On the basis of the steady - state semi - empirical model of the tire and the concepts of the relaxation length and the effective slip ratio, a non - steady semi - empirical model to express the tire longitudinal - slip response to the low - frequency input of the transient vertical load and transient slip ratio was presented
摘要在穩態半經驗模型的基礎上，根據鬆弛長度和有效滑移率的概念建立了能表達時變垂直載荷及時變滑移率低頻輸入下的輪胎縱滑特性非穩態半經驗模型。 -
It applies an interval method to select element in the evolutionary structure optimization method ( eso ), and recovers or deletes element by the “ birth and dead ” function of element. another method viewed as second order smoothing technique for suppressing the checkerboard patterns has been proposed based on the filtering function ’ s principle. then the above methods are applied to solve a temperature - controlling problem in the steady heat conducting field and a multi - objective topology optimization problem considering multiple load cases and coupled effect
本文基於ansysparametricdesignlanguage （ apdl ） ，提出漸進結構法中應用區間法進行單元的篩選，通過單元「生死」的功能實現單元的恢復與刪除，根據濾波函數法原理提出修改的二階棋盤格處理方法，並就穩態熱傳導溫度控制問題，考慮熱、力耦合的多載荷工況的多目標拓撲優化設計問題進行求解。 -
The first chapter quotes three methods for determining the steady - state equivalent circuit parameters of an induction machine. they are the classical locked - rotor and no - load tests, the direct modification method and the recursive least - squares method. then a new parameter estimation method based on genetic algorithms is presented
緒論首先引述了確定感應電動機穩態模型參數的其他三種方法：傳統的空載和堵轉試驗方法、直接修正參數法和遞推最小二乘法，並由此提出基於遺傳演算法的參數識別技術。 -
The rules obtained from the background modal analysis method based on the quasi - steady assumption in frequency - domain are similar to those obtained by the analysis method in time - domain, and the influence of high modes can be considered. finally, the dissertation suggests that for engineering design, it is better to use equivalent wind load factor defined the ratio of wind - induced total displacement to static displacement for computing the equivalent static wind load of long - span grid roof structures, and the equivalent wind load factor of the roof of taizhou stadium is calculated
最後通過對大跨網架屋蓋結構的風振系數的研究，提出了在實際工程設計中，採用位移風振系數來計算大跨屋蓋的等效靜力風荷載既正確又方便使用，並且給出了臺州體育中心看臺屋蓋進行分塊統計后的位移風振系數，以供設計參考。 -
The test results demonstrate that this prototype has excellent comprehensive performances such as small bulk, lower weight, high efficiency, high steady precision, fast dynamic response, wide range input voltage, good output waveforms, strong over - load and short - circuit ability, and strong function with different nature load and three - phase unbalanced load
試驗結果表明，該變流器具有體積重量小、變換效率高、靜態精度高、動態響應快、輸入電壓變化范圍寬、輸出波形質量高、過載與短路能力強、帶不同性質負載和帶三相不平衡負載的能力強等優良的綜合性能。 -
A new aerodynamic design system developed by authors for draft fan with enhanced efficiency, suppressed noise, enlarged flux and high load. the new design system features : a twist regulation for vortex control is employed in designing to lessen the secondary flow loss in the blade tip and hub ; the feasibility and high efficiency of this procedure has been verified by the tests of the prototype fan ; a new computer - aided 3d blading is used to optimize the blade ; numerical inverse checking is adopted to enhance accuracy in designing and cut down the period of the designing and production. this design system can make the optimized blade with " forward inclination ", " inclining sweep ", " bending sweep ", to minimize the various secondary flow losses, to expand the steady working range of the fan, and to suppress the aerodynamic noise source
本文通過對一種新型高性能礦用局部通風機的設計、製造及試驗全過程的綜述，展現了新的先進設計體系在民用通風機上的成功運用，其研製特點是： （ 1 ）在葉片氣動設計中為了降低葉根及葉尖區二次流損失，採用可控渦扭向規律設計，樣機實測的高性能驗證了這種方法的可行性和高效性； （ 2 ）在設計方法中採用較精確的數值反驗算，獲取最優設計方案，大大提高設計的準確性和成功率，並縮短了設計試制周期； （ 3 ）在設計過程中發展了計算機輔助三維葉片造型新方法，可以根據設計需要簡便快捷地對葉片進行「前傾」 、 「傾掠」或「彎掠」造型，這些造型對減小各種二次流損失、擴大穩定工況范圍和控制葉輪機氣動噪聲源起到了非常好的作用。 -
Abstract : a new aerodynamic design system developed by authors for draft fan with enhanced efficiency, suppressed noise, enlarged flux and high load. the new design system features : a twist regulation for vortex control is employed in designing to lessen the secondary flow loss in the blade tip and hub ; the feasibility and high efficiency of this procedure has been verified by the tests of the prototype fan ; a new computer - aided 3d blading is used to optimize the blade ; numerical inverse checking is adopted to enhance accuracy in designing and cut down the period of the designing and production. this design system can make the optimized blade with " forward inclination ", " inclining sweep ", " bending sweep ", to minimize the various secondary flow losses, to expand the steady working range of the fan, and to suppress the aerodynamic noise source
文摘:本文通過對一種新型高性能礦用局部通風機的設計、製造及試驗全過程的綜述，展現了新的先進設計體系在民用通風機上的成功運用，其研製特點是： （ 1 ）在葉片氣動設計中為了降低葉根及葉尖區二次流損失，採用可控渦扭向規律設計，樣機實測的高性能驗證了這種方法的可行性和高效性； （ 2 ）在設計方法中採用較精確的數值反驗算，獲取最優設計方案，大大提高設計的準確性和成功率，並縮短了設計試制周期； （ 3 ）在設計過程中發展了計算機輔助三維葉片造型新方法，可以根據設計需要簡便快捷地對葉片進行「前傾」 、 「傾掠」或「彎掠」造型，這些造型對減小各種二次流損失、擴大穩定工況范圍和控制葉輪機氣動噪聲源起到了非常好的作用。 -
Hunting hunting is a phenomenon that can occur upon load changes in which the frequency or the voltage continues to rise above and fall below the desired value without reaching a steady - state value
游車游車是一種在負載變化引起的頻率、電壓高於或低於期望值，無法達到穩定的現象。 -
The simulation results indicate that the algorithm is suitable for the speed regulation of srm. within a wide speed range the system has a good regulation character and a high precision of steady state, also the system can well constrain the disturbance of the load torque varying
模擬結果表明，採用本演算法構成的sr電機凋速系統在整個調速范圍內具有良好的調節性能及穩態精度，對負載轉矩的變化造成的擾動輸入能夠很好的加以抑制。 -
The list betterments aimed at the properties of system : through the testing of dc voltage, pulse width and inverting voltage and frequency can be regulated online to fit for different steady load ; reducing speed ripples by compensating with nonzero voltage working proportional time ; adopting the technology of harmonics suppression. as a result, the high precision and wide speed control is realized and the step out is overcome
針對系統的性能指標，做了如下改進：對直流側電壓的檢測，在線調整逆變器導通脈寬、輸出電壓和頻率，可以適應不同大小的恆負載；並用非零電壓矢量作用時間進行補償的方法，減小電機的低速脈動；加入了諧波抑制技術等。
分享友人