stretched plate 中文意思是什麼
stretched plate
解釋
拉伸板-
It is made of quality steel plate, which is stretched forming welded and plastic sprayed with bubble cement filled in its inner cavity. its pedestal is plated with zine and cast aluminum alloy, which height is adjustable and can be self - locked
線槽蓋板，地板採用優質鋼板經拉深成型點焊噴塑內腔填充發泡水泥填料，支座為鍍鋅結構，高度可調並能自鎖。 -
And over jerusalem will be stretched the line of samaria and the weight of ahab ; jerusalem will be washed clean as a plate is washed, and turned over on its face
我必用量撒瑪利亞的準繩、和亞哈家的線鉈、拉在耶路撒冷上必擦凈耶路撒冷、如人擦盤將盤倒扣。 -
[ bbe ] and over jerusalem will be stretched the line of samaria and the weight of ahab ; jerusalem will be washed clean as a plate is washed, and turned over on its face
我必用量撒瑪利亞的準繩、和亞哈家的線鉈、拉在耶路撒冷上必擦凈耶路撒冷、如人擦盤將盤倒扣。 -
Machining deformation of aircraft monolithic component is simulated by finite element method ( fem ) and validated by experiment. the initial residual stress in pre - stretched plate is generated by simulating quenching and stretching processes. with a single tool - tooth milling process fem, the machining loads in monolithic component material removing is obtained. restart - calculation is put forward to complete the whole simulation of machining process. to verify the fem result, an experiment is carried out. the deformation distribution of the monolithic component resulting from fem shows a good agreement with the experiment result, which indicates that the key technologies presented in the paper are practicable and can be used to simulate the milling process of monolithic component to predict its deformation. lengthy and expensive trial and error experiment process can be avoided
在模擬淬火、拉伸過程獲得含有初始殘余應力的預拉伸板材以及模擬單齒切削過程獲得切削載荷的基礎上，提出並採用接力演算法，對一航空整體結構件的材料銑削過程進行有限元模擬，同時進行了試驗研究.結果表明，有限元模擬的整體結構件的變形與試驗具有一致性，從而證明提出的整體結構件加工模擬關鍵技術的可行性，避免了為研究加工變形而進行的繁瑣的試錯法 -
It is madeof quality steel plate, which is stretched forming, point welded and plastic sprayed with bubble cement filler filled in its inner cavity. its pedestals are plated with zinc and cast aluminum alloy, which height is adjustable and can be self - locked
四角連體支承結構，採用優質鋼板經拉深成型點焊噴塑，內腔填充發泡水泥填料，支座為鍍鋅及鑄鋁合金結構，高度可調並能自鎖。 -
1. the measurement method of residual stress distribution in thick aluminum alloy plate is studied. aiming at the difficult problem to measure residual stress distribution in thick plate, a new method is proposed - - modified layer removal method, based on existed measurement theories and according to the characteristics of thick pre - stretched aluminum alloy plate
本文所完成的主要工作如下: 1 、鋁合金預拉伸厚板內部殘余應力的測試方法研究針對厚板內部殘余應力測試這一技術難題，在現有測試技術研究的基礎上，結合鋁合金厚板的特點，提出了一種新的測試方法? ?改進剝層法。 -
I set his plate to keep warm on the fender ; and after an hour or two he re - entered, when the room was clear, in no degree calmer : the same unnatural - it was unnatural - appearance of joy under his black brows ; the same bloodless hue, and his teeth visible, now and then, in a kind of smile ; his frame shivering, not as one shivers with chill or weakness, but as a tight - stretched cord vibrates - a strong thrilling, rather than trembling
我把他的盤子放在爐柵上熱著，過了一兩個鐘頭，他又進來了，這時屋裡人都出去了，他並沒平靜多少：在他黑眉毛下面仍然現出同樣不自然的的確是不自然的歡樂的表情。還是血色全無，他的牙時不時地顯示出一種微笑他渾身發抖，不像是一個人冷得或衰弱得發抖，而是像一根拉緊了的弦在顫動簡直是一種強烈的震顫，而不是發抖了。 -
Finally, the technic route for the research of milling distortion is proposed. in chapter 4, the effect of tool path and clamping schemes on residual stresses as well as machining distortion are analyzed by using three - dimensional elastic - plastic fem ( finite element method ). the distortion variation tendency under four typical tool paths, the pressing - plate clamping and stretched fixation is obtained respectively
第四章基於上述理論基礎，利用三維彈塑性有限元技術分析了走刀路徑和裝夾方案對銑削加工殘余應力分佈和變形的影響，得到了四種典型的走刀路徑以及壓板式裝夾和拉伸裝夾對加工變形的影響趨勢。
分享友人