surface load 中文意思是什麼

surface load 解釋
表面負荷
  • surface : n 1 表面；地面；水面；廣場，空地。2 外觀，外表，皮毛。3 【幾】面；切口；【航空】翼面。adj 表面的...
  • load : n 1 裝載，擔子；負擔；工作（負荷）量。2 （車船等的）裝載量；一馱，一車，一飛機。3 【電、機】（機...
  1. Surface and air vehicles - unit - load heights for palletized loads

    地面和空中貨物運輸.托盤化運貨用成件貨物的高度
  2. The company produces the table history to be glorious, and develops the innovation unceasingly, develops from the initial straight strip surface of bed table foundation to shan qubo the surface of bed table to the hyperbolic wave surface of bed table, causes the table the process load, the returns - ratio and concentrates compared to all has the large scale enhancement

    我廠生產搖床歷史悠久，並不斷開發創新，從最初的直條床面搖床基礎上發展到單曲波床面搖床（上世紀70年代） ；到雙曲波床面搖床（上世紀90年代） ，使搖床的處理量、回收率和富集比都有大幅度的提高。
  3. If this load centroid is behind the elastic axis of the wing structure, then a nose-down twist of the main wing surface results.

    如果該載荷重心在機翼結構彈性軸之後，則引起主機翼表面前端向下的扭轉。
  4. At supersonic speeds the control load acts mainly on the deflected surface itself, and hence has its centroid even farther to the rear.

    超音速時操縱載荷主要作用在偏轉面本身上，因此它的作用中心甚至更加靠後。
  5. It calculate 60 driving speed kilometers / hour, it design 30 kilometers of speed of deck bridges road, ground of offices / hour, road calculate and load type standard cars standard bzz - 100s, iron do distance to city one for new urban north and southses by mountain path by road surface structure, calculation 40 driving speed kilometer / hour

    計算行車速度60公里/小時，跨線橋處地面道路設計車速30公里/小時，道路路面結構計算荷載標準bzz - 100型標準車，鐵山路為新城區南北向城市次幹路，計算行車速度40公里/小時。
  6. This system contains : parts load, pre - degrease, degrease, spray cleaning, spray surface adjustment, spraying phosphating, rinse with d - ionized water, electro - deposition, ultra - filter for post rinse, oven curing, cooling and unload

    由上件，預脫脂，脫脂，噴洗，噴淋表面調解，噴淋磷化，去離子水噴洗，電泳塗裝，超濾液噴洗，漆膜固化，自然冷卻，下件工序組成。
  7. It seems that increasing the surface area of inseration with the dentin improves the distribution of the load caused by the insertion of the post

    （ 3 ）側向受力時：螺旋根柱應力分佈隨施力方向，在施力處對側應力增加，而根柱長短及直徑大小的影響和垂直受力時相似。
  8. About the load, consider the vertical load, when under the action of water, consider the horizontal still water press, the press which erects to the surface of slide, and consider the effect of hydrodynamic load and earthquake. ( 3 ) the software about the frame design, apply the stiffening bar method and elastic foundation method to account the endogen

    對于荷載（或工況） ，考慮了外加垂直荷載；在有水作用的情況下，考慮了水平靜水壓力，垂直滑面的靜水壓力（也叫浮托力） ；考慮動水壓力的影響；同時也考慮了地震的影響。
  9. Estimation of intramuscular load of the upper limb in static postures and repetitive work by surface electromyography

    手臂靜態姿勢和反復性操作負荷的肌電測定分析
  10. The pivot and race surfaces were true surface of revolution and were correctly centered when no load was applied.

    軸樞和套圈的表面是準確的旋轉表面，並在未施加載荷正確對中。
  11. The " xinguan brand building material and industrial material has more than 300 series including 2000 specifications. their surface has been already dealt with three crafts : positive pole oxidize, electrophoresis scribble load with, powder spraying. the color incorporates the international popular color ; quality of the product reaches the international standard

    生產的「鑫冠」牌建築型材工業型材已擁有300多個系列，近2000餘種規格，表面處理已形成陽極氧化電泳塗裝粉末噴塗三大工藝，色彩融入國際流行色，產品質量達到國際標準，被評為江蘇省信用產品，省鄉鎮企業名牌產品，全面通過iso90012000質量體系認證。
  12. The temperature effect which has been calculated is taken as " thermal load " forced on the body, then such thermal stress is settled as general elasticity mechanics question ; secondly, the thermal stress is taken as " surface force " forced on the body, and the new system stiffness is formed which include the extra stiffness matrix, then it changes the nature frequency of the structure

    首先，這篇論文介紹溫度場和熱應力場的有限元方法，建立了三維熱傳導模型計算有溫度場產生的熱應力，計算熱應力時運用了一種轉化思維：將溫度處理為「溫度載荷」 ，這樣就能用彈性力學問題的處理方法來求解熱應力。其次，將熱應力作為結構的「面內力」 ，而面內力產生附加的幾何剛度矩陣，改變了結構的剛度，影響了結構的固有頻率。
  13. The fem analysis for the three structures of sling screw - thread - based, namely the circle, rectangle and that with strengthen plate, and the tensile test for sling screw - thread - based in torpedo body show, that the bonding with strengthen frp plate between load - bearing metal parts and frp hull with hatch can reduce the stress concentration and significantly decline the local stress in frp hull with hatch. this structure can also be used in the similar produces. ( 3 ) the effects of parameters for bonding process on the adhesive strength and leakproof are discussed, such as the bonding interface reduce, bonding surface treatment, match of adhesive surface, protect for adhesive seam and so on

    本文通過某型號雷體吊耳螺紋座結構的三種方案，即圓形昂耳螺紋座、長方形吊耳螺紋座、具有增強板的吊耳螺紋座的有限元分析及雷體吊耳螺紋座拉力試驗結果證明：金屬承力件與開口玻璃鋼殼體粘接採用玻璃鋼增強板補強，緩和了應力集中，使開口殼體局部應力明顯降低，類似的水下兵器用金屬承力件與開口復合材料殼體膠接均可採用此種結構形式。
  14. The analytical model indicates that the rubbing temperature of tire surface is affected by some parameters, such as ambient temperature, sliding speed and distance, normal load and thermal - mechanical properties of the counterface materials, as well as geometric shape of a tire footprint

    分析了大氣溫度、滑動距離、滑動速度、輪胎承載以及胎面和路面材料的物理性能對接地胎面溫度的影響。
  15. We conclude that the conjunction intensity between the platform and piles has a prominent impact on the deformation on the surface and there exists the " curtain effect " of the pile that weakens the slide tendency to the sea. it is confirmed the most disadvantageous load cases

    通過數值模擬得到以下結論，承臺與樁頂連結對碼頭頂面的側向位移影響顯著；存在樁的「遮簾作用」 ，它在一定程度上弱化了岸坡土體向海方向的位移趨勢；確定出對碼頭穩定性最不利的工況荷載組合。
  16. Standard of test method for surface load capacity of gears

    齒輪接觸疲勞強度試驗方法
  17. After determining the max furnace temperature, calculate the power ( kw ) of a single element using the way of multiplying the stipulated surface load of the elements under said furnace temperature ( find it out from the above table ) by the surface area of hot zone of the elements. ( find it out from the product dimension

    確定最高爐溫后，根據元件在此爐溫下所規定的表面負荷，乘以所選元件發熱部的表面積（從產品規格表中查出） ，求出單支元件的功率（ kw ） 。
  18. The heater is cooking heat source in the microwave oven. generally 2 pcs. as one suite in series and the power of single tube is 400w 600w. bigger surface load and higher radiating coefficient make the microwave cooking food more quickly

    本加熱器在微波爐中為燒烤熱源，一般一組為2隻串聯使用，單管功率一般為400w600w ，表示負荷較大，且石英管表示的熱輻射系數高，使微波爐燒烤食物更加快捷。
  19. The influence of surface load to critical affection depth in goaf

    地面荷載對地下采空區的臨界擾動深度及其影響
  20. The shear - lag effects were mainly analyzed under surface load and focus load, and the different was dissnssed that impact to dynamic analysis of these two models

    所得的分析結果對指導這類橋梁的設計具有重要的工程實用價值。
分享友人
分享到 Line

分享到臉書