switch wheel 中文意思是什麼

switch wheel 解釋
機鍵輪
  • switch : n 1 （樹上折下的）細樹枝；軟鞭子；鞭打。2 假發；（尾巴上的）毛簇。3 〈美國〉【鐵道】道岔扳子，軌...
  • wheel : n 1 輪，車輪；輪狀物。2 〈口語〉腳踏車；【造船】艙輪；（汽車的）方向盤，駕駛盤；（制陶）轉盤；紡...
  1. Down chiang minus shan wheel switch position exorbitance, go back to floor behind has not on down blade hand in will inner

    下強減單輪開關位置過高，歸樓后未在上下刀片交會內
  2. Down chiang minus shan wheel switch position exorbitance, elevator come down shih disapprove down chiang minus signal first yu down slow down signal

    下強減單輪開關位置過高，電梯下降時不可以下強減信號先於下減速信號。
  3. Down chiang minus shan wheel switch position exorbitance, elevator come down shih disapprove down chiang minus shan wheel signal first yu down slow down signal. please

    下強減單輪開關位置過高，電梯下降時不可以下強減單輪信號先於下減速信號。
  4. Check the gear wheel drive in the groove of the wall, select four gear wheel ( red pinion is not used ) of different size for use, load heavy gear wheel, times of heavy gear wheel, times of light gear wheel, minimum gear wheel most onto separately from left to right, make gear wheel hand in, form each other, leave behind, operate a switch, drive, finish

    檢查墻壁凹槽中的齒輪驅動裝置，選用大小不同的四個齒輪（紅色的小齒輪不用） ，從左到右分別裝上最大的齒輪、次大的齒輪、次小的齒輪、最小的齒輪，並使齒輪間相互交結，拉下拉閘，驅動完成。
  5. This machine is used for straight - line bevel cutting and bevel grinding and polishing for flat glass, in certain condition, it can be also used in bevel cuttig, bevel grinding and polishing for soft stone panel. the contrilling system adopts plc, it can accomplish automatic grinding cutting after entering processing parameter, convery speed adopts speed adjustment of fre quency conversion, direct drive of wheel head motor, all motions for joining in parameter adjustment completely adopt straight - rolling guide - track with front beam and wheel head lifting lntegrally. the transmission of input and output adopts synchronization tooth belt and photo - electricity switch positioning, and position limitation of two pass is much more reliable

    Sxm371pa型玻璃直線斜邊磨邊機是用於玻璃直線斜邊斜切，斜磨及光拋的專用設備，在一定條件下也可以用於軟石板材的斜切斜磨及拋光。控制系統採用plc控制。輸入加工參數后可自動完成磨削傳送速度採用變頻調速，磨頭電機直接傳動，所有加工參數調整運動副全部採用直線滾動導軌，前梁與磨頭整體升降，輸入輸出傳送採用同步形帶，光電開光定位，雙行程限位更安全可靠。
  6. Control record / play / stop functions remotely using any midi controllers such as a foot switch, modulation wheel

    控制記錄/播放/停止功能遙控使用任何midi控制器如足部開關，調制輪。
  7. Push wheel switch

    溫度斷路開關
  8. Up chiang minus shan wheel switch position kuo low, elevator rise shih disapprove up chiang minus signal first whereon slow down signal

    上強減單輪開關位置過低，電梯上升時不可以上強減信號先於上減速信號。
  9. Up chiang minus shan wheel switch position kuo low, elevator rise shih disapprove up chiang minus shan wheel signal first whereon slow down signal. please

    上強減單輪開關位置過低，電梯上升時不可以上強減單輪信號先於上減速信號。
  10. While the theory of wheel / rail system dynamics is applied in the points ( switch ) dynamics, the system is more complicated and computation time is longer, therefore the parallel computing technology is an effective method to increase computation speed

    特別是隨著輪軌系統動力學在道岔動力學中的應用，處理的問題更加復雜，計算時間長的問題，已成為實際應用中的一大障礙。提高其計算速度的一個有效方法就是採用并行計算技術。
  11. According to the idea, five - wheel device converting the straight line movement into the rotation movement which is convenient to measure, a non - contacting velocity measurement sensor device using optical switch and steel tapeline to measure the straight line movement has been designed and produced, which is an exploration in this field

    根據五輪儀「把不易測量的直線運動轉變為容易測量的轉動」的思路，利用光微開關和捲尺鋼帶設計製作了一種非接觸式的直線運動物體速度測量傳感裝置，是一個具有創造性的探索。
  12. Down chiang minus shan wheel switch position kuo low, go back to floor behind has not on down blade hand in will inner

    下強減單輪開關位置過低，歸樓后未在上下刀片交會內。
  13. To switch combined pedals off goto ? ame controllers ? from the control panel, select your steering wheel then click on properties and then settings, now untick the combined box

    要關閉結合踏板選項，只需從控制面板中選擇游戲控制器，選擇你的方向盤並點擊參數，然後選擇設定，取消結合踏板的復選框。
分享友人
分享到 Line

分享到臉書