tangent modulus stress 中文意思是什麼
tangent modulus stress
解釋
正切模數應力-
The existed material fatigue performance test curves are dealt with and analyzed, and the non - dimensional stress - strain curve, tangent modulus factor curve and fatigue life curve are drawn based on the experiment data, and these three non - dimensional parameter curves are used to find the inherent rules that the test curves can be replaced each other to some extent. it can be concluded that if the common character and system error of these materials are found, the test curve of a certain material can be used for reference by another material. this is a simple approach about fatigue life estimate and is engineering practical
對已有的材料力學疲勞性能試驗曲線進行分析整理，利用試驗數據繪制了相對應力應變曲線、切線模量因子曲線和疲勞壽命曲線，利用這三種無量綱參數曲線發現了其中存在的規律性，即在某種程度上實驗曲線可以互相取代，並用試驗數據對此進行了討論，並由此推斷，如果找出材料彼此的共性或彼此之間的系統誤差就可以將一種材料的試驗曲線供其它材料參考使用，這是一種估算材料的疲勞壽命的簡便方法，對工程而言具有實用性。 -
The static triaxial test of two engineerings shows that the breaking strength of asphalt concrete declines significantly as the temperature rises and the strain increases noticeably when breaking. increase in the asphalt content leads to decrease in tangent modulus and cohesion, but the internal friction angle tends to increase. increasing confining stress results in the augment of the maximum stress and the ultimate value of volumetric strain
兩個實際工程的靜三軸變形與強度試驗表明，隨著溫度升高瀝青混凝土破壞強度明顯降低，破壞時應變明顯加大；瀝青含量的增加會導致切線模量和凝聚力降低，但內摩擦角趨于增加；周圍壓力增大會導致最大應力_ d增大，其體變壓縮極限值也越大。 -
If asphalt concrete specimen is in stabilization by exert confining stress before the static triaxial test, it is then found that under the condition that time is long enough, the volume of the specimen will shorten gradually and stable around a fixed value, and the amount of compression is essentially the half of the volume of void itself. it is also found that in stabilization by exert confining stress the linear phrase will be shorten in the figure of the static triaxial test of specimen, while the initial tangent modulus will be augment. 3
在進行靜三軸試驗以前先對瀝青混凝土試件進行圍壓穩定，發現在時間足夠長的條件下，試件的體積會逐漸縮小，並逐漸穩定在某一定值，其壓縮量基本上為其本身孔隙體積的一半；經圍壓穩定后的試件靜三軸試驗曲線上的線性階段明顯縮短，而初始切線模量增大。 -
Theory analysis in this paper pointed out that the flexural - torsional buckling is the usual form of t - section steel. so the slenderness ratio of flexural - torsional buckling should be used when people give out the b / t ratio by the " equal stability " conception. initial stress, defects and tangent modulus are include in the deduce of the paper to get a rational b / t ratio
通過理論分析指出軸心受力剖分t型鋼整體失穩以彎扭屈曲為主，所以在運用「等穩定」方法確定腹板寬厚比限值時應與桿件的扭轉長細比「掛鉤」 ，並以此為出發點考慮殘余應力、初始缺陷，應用切線模量推導出了較為合理的腹板寬厚比限值公式。 -
The results showed that the stress - strain realtionship of pt could be expressed with exponential functions, and there were significant differeces between the normal group and the immobilized group in their theoretical curves of stress - strain relationship and two material constants of pt. also, significant differences were found in tensile strength and tangent modulus between the two groups, but the maximum load of pt in the immobilized group did not decrease significantly
結果顯示：正常組與制動組間髕韌帶的應力-應變關系理論曲線有明顯不同，其材料常數亦有顯著差異；制動組髕韌帶的極限強度和彈性模量較正常組均有明顯下降，其極限載荷下降不明顯。
分享友人