tangential stress 中文意思是什麼

tangential stress 解釋
剪應力
  • tangential : 表面的
  • stress : n 1 壓力，壓迫，緊迫，緊張。2 【語音】重音；重讀；【詩】揚音；語勢，著重點。3 重要（性），重點，...
  1. Sm scales the nonlinear variation of tangential modulus during monotonic loadings into a piecewise linear distribution, which can easily be modified to simulate specific characteristics of soil material behavior during cyclic loadings. sm can simulate dynamic stress - strain response of arbitrary cyclic loadings

    該模型將單調加載情況下呈非線性變化的切線模量量化成一種呈分段線性分佈的幾何結構，並通過對這種結構加以變換，來描述循環加載情況下材料的特性。
  2. The distributions of the local density, thickness, temperature, tangential and normal stress and surface tension were acquired by the study of liquid - vapor interface. these simulated data agree well with corresponding experimental data and the md simulation results from other authors, consequently it is proved that the model and simulation method in the paper are correct

    對汽液界面進行了分子動力學研究，獲得了汽液界面局域的密度、厚度、溫度、切向應力和法向應力以及表面張力的分佈，並把這些數據與相應的實驗數據和其他作者的模擬結果相比較，吻合較好，從而證明了本文所採用的模擬方法和模擬模型是正確的。
  3. When a ferromagnetism items is under the application of stress, the phenomenon that the tangential component of magnetic leakage field has maximum value and that the normal component of magnetic leakage field changes polarity and acquires zero value at the stress concentration zone will take place

    鐵磁性工件在受到應力作用時，在應力集中處會有漏磁場的切向分量出現最大值、同時法向分量改變符號且過零值點的現象。
  4. The mathematic model of the ultra - thin spherical mirror is to be treated as elastic thin shell. then the predigested model, i. e., bended beam, used in qualitative analysis was proposed, and its deflection and stress formulas under the freely supported condition were set up. based on an off - axis aspherical primary mirror, the relationship of aspherical surface error ( rms ) in tangential plane with bended beam ’ s radius r, position s of concentrated load p and geometry length l of arc was analyzed

    根據這一設想，本文建立了超薄鏡的數學模型?薄殼，並提出了強制力作用下超薄鏡的簡化模型?曲梁，推導了曲梁在簡支情況下受力變形的撓度公式，並結合一個實例，計算出曲梁變形后與所需非球面的面形殘差（ rms ）在子午方向與曲梁弧長l 、曲梁半徑r及集中力位置s的關系及滿足面形精度的r和s范圍，分析了弧矢方向的rms ，得出了同時滿足子午和弧矢方向面形要求的l 、 r和p 。
  5. According to the effective field expression which has been derived in former, the phenomenon that the tangential component of magnetic leakage field has maximum value and the normal component of magnetic leakage field acquires zero value at the stress concentration zone of positive magnetostriction ferromagnetism materials under the application of tensile stress and negative magnetostriction ferromagnetism materials under the application of compressive stress is explained theoretically through analyzing and discussing

    根據所得到的地磁場中受力鐵磁性材料有效場表達式，通過分析討論，解釋了受拉力作用的正磁致伸縮鐵磁材料和受壓力作用的負磁致伸縮材料在應力集中處漏磁場切向分量出現最大值、同時法向分量為零值的現象。
  6. Stress analysis for tangential bonded structure of pressure vessel and pipe based on finite element method

    壓力容器與切向接管結構應力三維有限元分析及強度評定
  7. Tangential wind stress

    切向風應力
  8. In this paper, the equilibrium equation of liquid bulge forming small tangential round corner is deduced for the complicated shape tube - type blank, the function equation between forming stress parameters are and the small corner are obtained ; the forming mechanism of the small tangential corner is studied, the matching relation between liquid bulging pressure and axial thrust is given, the optimal liquid bulging force parameters are determined

    摘要本文推導出復雜形狀管類件復合液壓脹形時環向小圓角成形的平衡方程，得出了成形應力與環向圓角半徑的解析關系；研究了環向小圓角成形機理，確定了液體脹形壓力與軸向推力的匹配關系以及最佳的成形力參量。
  9. Abstract : in this paper, through stress analysis of region about conical and spherical parts during drawing, a calculating formula of maximum tangential compressive stess in unsupported wall region is deduced. and this is condition of causing internal wrinkle. then on the premise to guarantee not breaking workpiece, a critical calculating formula is presented

    文摘:通過對球形和錐形零件在拉深過程中各部分的應力分析，得到了拉深過程中懸空區切向壓應力最大值的計算公式，以此作為引發內皺的條件，在保證工件不被拉裂的前提下，建立了臨界計算公式。
  10. In this paper, through stress analysis of region about conical and spherical parts during drawing, a calculating formula of maximum tangential compressive stess in unsupported wall region is deduced. and this is condition of causing internal wrinkle. then on the premise to guarantee not breaking workpiece, a critical calculating formula is presented

    通過圓筒形及盒形件拉深前後網格變化分析，並確定變形區和非變形區，由此得到不規則盒形件毛坯展開形狀由不變形區和參與變形拉深線組成，並用此方法計算出汽車制動閥安裝板的毛坯形狀和尺寸，在試模時一次即獲得成功，具有一定的實用價值。
分享友人
分享到 Line

分享到臉書