temperature joint 中文意思是什麼

temperature joint 解釋
溫度縫
  • temperature : n. 1. 溫度，氣溫。2. 體溫。3. 〈口語〉發燒，高燒。
  • joint : n 1 接合，榫接合處，接合點。2 【解剖學】關節。3 【植物；植物學】節。4 【電學】接頭。5 【建築】接...
  1. The elasticity polyurethane joint sealing material is one kind of joint sealing materials for concrete pavement joint which can use at normal temperature. it will solidify by chemic - reaction when commix the polyurethane preploymer, cross link agent, filling, plasticizer and catalyzer

    聚氨酯彈性嵌縫料是一種由聚氨酯預聚體主劑與交聯劑、填料、增塑劑以及催化劑混合后通過化學反應交聯固化的常溫施工式水泥混凝土路面用嵌縫材料。
  2. Failure analysis of special steel soldered joint of high temperature reheater

    高溫再熱器異種鋼焊接接頭失效分析
  3. High temperature mechanical properties of manual argon arc welded joint of 10cr9mo1vnb steel

    鋼手工氬弧焊焊接接頭的高溫力學性能
  4. Direct connect vias conduct so much heat away from the pin and into the plane that high temperature or long soldering time may be required to complete the joint - thermal damage could occur to both the board and the component from soldering or desoldering

    在焊接時，直接連接的過孔會通過引腳把大量的熱傳導至內電層，因此完成焊接就需要很高的溫度或者延長焊接時間，這就會導致在焊接或拆焊時發生電路板或元件的損壞。
  5. This article introduced the development and ti - based brazing material used for titanium alloys, and analyzed the relationship between metallurgical structure and mechanical property of welding joint, mechanical behavior under high temperature 、 corrosion resisting property and fatigue capability of the joint were also represented

    本文介紹了鈦合金用的鈦基釬焊料的發展現狀，重點評價了鈦基釬料釬焊后組織與力學性能的關系，以及鈦基釬料的高溫力學性能、耐蝕性以及疲勞性能等。
  6. ( 2 ) the stress caused by heat of hydration during construction is mainly distributed in the beams, and girders and stress in slab was smaller ; during service process, the stress caused by difference in temperature in different seasons is mainly distributed in bottom components ; the stress caused by difference of inside and outside temperature is mainly distributed in peripheral components of building ; the stress caused by difference in temperature due to sunlight is mainly distributed in the components exposed to the sun. ( 3 ) the control methods brought forward such as setting the reasonable stripping time reducing cast temperature of concrete setting after - treatment joint inflicting prestress arranging steel for construction requirement and so on are effective and their application may be extended

    在使用期，由季節溫差作用引起的結構內力主要分佈在底層構件上；由內外溫差引起的內力主要分佈在建築物外圍構件上；由日照溫差引起內力主要分佈在向陽面的構件上； （ 3 ）在施工階段，可採取使用導熱性能較好的模板、合理設計拆模時間、降低澆築溫度等措施來減小水化熱引起的結構內力；採用設置后澆帶的措施來減小結構在整體降溫情況下產生的溫度內力。
  7. An analysis of simulation of welding temperature in the t - joint

    型接頭焊接溫度場的有限元模擬
  8. Analysis on the causes of damage, this paper modified the meijia bitumen materials in order to enhance the low temperature capacity of bitumen and bituminous mixture through the polymer. emphasis on the study of low temperature capacity of modified asphalt and bituminous mixture, we utilize reasonable construction craft to avoid the cracks problem between bituminous mixture and bridge and give a advance way of small or moderate span bridge expansion joint in low temperature areas

    針對這一缺陷，本文通過添加熱塑性橡膠類改性劑和橡膠類改性劑，對美佳改性瀝青結合料進行二次改性，重點研究了改性后瀝青結合料和混合料的低溫性能，並採用合理的施工工藝解決填縫料與梁端間存在的界面裂縫問題。
  9. The result shows that tempered martensite has apparent lath character when temper is between 740 ~ 780, and the hardness of welded joint is 264 ~ 237hv, which can get better performance of the welded joint the lath character of martensite in welded joint disappears, and the carbide in the tempered sorbite of the base metal will aggregate when temper temperature is above 780, and the hardness and plastic property will reduce obviously

    結果表明，在740 ~ 780之間回火，焊縫硬度為264 ~ 237hv ，回火馬氏體板條特徵明顯，可以獲得優良的焊接接頭性能；回火溫度超過780 ，焊縫板條馬氏體特徵消失，母材回火索氏體中碳化物產生偏聚，硬度、塑性明顯降低。
  10. This type of joint have been widelu used in the steel pipeline system for connection, it has a very good self - compensation performance while temperature change and angle deviation of the pipeline axis

    鍛壓卡箍式柔性管道接頭該產品具有溫度自補償和角度自補償功能，是鋼制管道系統中廣泛應用的聯接件，其結構合理、耐壓強度高、密封性能好，安裝維修方便。
  11. Viz. sbwz246pw g230 300150 0100 means integral temperature transmitter, pt100, 24vdc, 420ma, power - output is two - wire, no integral indicator indicator, water - proof joint box, fixed screw thread, tube diameter is 16 total length is 300mm, insert depth is 150mm, measuring range is 0100

    裝非隔離型防爆標志為exdbt4 ，則型號為： sbwr256ty g25dd 1000850 2001600保護管材料鋼玉管，固定螺紋m121
  12. The heat transfer and the restriction circumstance are simulated. the temper ature - time curve and the stress - time curve are obtained. because the later joint - filled slots are restrained strongly, in which the thermal stress is great, especially in the corner, in spite of a little temperature rise, some measures should be taken to prevent them from producing cracks

    利用有限元前處理軟體vizicad建立了「 t 」形后澆帶模型，模擬了后澆帶的「熱環境」和「約束環境」 ，計算得到了后澆帶的應力和溫度發展曲線，發現雖然後澆帶的溫升不大，但受到的約束較大，因此產生較大的溫度應力，特別是在其拐角處，應採取措施防止裂縫的出現。
  13. Three kinds of joint elements for finite element analysis of temperature field are given, ie, the joint element with finite thickness, the joint element with nearly zero thickness and the simplified joint element

    摘要目前混凝土壩的模擬分析正從單壩段模擬向全壩模擬發展，因而需要採用接縫單元，筆者給出三種溫度場接縫單元的計算模型：有限厚度接縫單元、近零厚度接縫單元及簡化接縫單元。
  14. This paper, in allusion to damage of expansion joint of bridge, introduces a sort of new structure of jointless device - semi - integral abutment jointless bridge, and establishes model of general structure finite element of this bridge, and in details analyses its qualities of stress. the model considers the interaction of superstructure - substructure - soil. resistance of the soil behind abutment adopts still soil pressure and elastic resistance when the temperature rising, but active soil pressure when dropping. analysis of qualities stress of bridge includes of action of dead load, car load, temperature load of season character. taking an 100m length pc semi - integral abutment jointless bridge as instance, the paper establishes the model of plane frame by applying large common software - anasys, and analyses it by elastane and large deformation to imitate character of stress and deformation of general bridge. at the same time corresponding models of finite element of joint bridge and integral abutment bridge are established, and unique stress and performance of structure of semi - integral abutment jointless bridge are researched by comparing and analysing character of three different models under same loading, and controlling factor of design and constitution are generalized. in conclusion, for semi - integral abutment jointless bridge, on one hand shear, moment and deflection of the main beam and axis force of substructure are approximate with that of joint bridge, and integral stifmess of structure is increased and damage of expansion joint is eliminated, on the other hand there is axis force in main beam, shear and moment of substructure are bigger than that of joint bridge. in all this type of jointless bridge has rational stress and is worth of application and popularization

    半整體式橋臺無縫橋梁計算模型考慮了上部結構-下部結構-土的共同作用；臺後土抗力升溫時採用靜止土壓力加彈性土抗力，降溫時採用主動土壓力；分析橋梁受力性能時考慮了結構自重、車輛荷載和季節性溫變荷載的作用。以一座橋長100mpc半整體式橋臺無縫橋梁為實例，採用大型通用軟體ansys建立平面框架模型，進行彈性、大變形分析，模擬全橋受力和變形特點；同時建立與此對應的有伸縮縫橋梁和整體式橋臺無縫橋梁有限元模型，通過三種橋型同步加載對比分析，研究半整體式橋臺無縫橋梁獨特的受力特點和結構性能，總結其設計控制因素和構造要求。通過本文研究知：半整體式橋臺無縫橋梁主梁的剪力、彎矩、撓度和下部結構的軸力與梁式橋相近，結構整體剛度增大，併除去了伸縮縫病害；但主梁增加了軸力，下部結構剪力、彎矩較梁式橋大；綜合分析是一種受力合理有實踐和推廣價值的橋型。
  15. Additions of carbon for improved slag resistance. spinel formation improves hot strength, slag resistance and brick joint erosion. 3 repairing material for bof uses fused magnesia or sintered magnesia as the main raw material and after modifid pitch and special additives are added, it has the following characteristcs than other conventional converter pitch temperature, shorter sintering time, longer service life and less pollution. it is mainly used for repairing converter working face, also for tapping side, tapping hole and bottom

    3 ，轉爐大面補料是採用電熔鎂砂或燒結鎂砂為主要原料，通過加入改性瀝青和特種添加劑使它和傳統瀝青補爐料相比具有高溫附著性好燒結時間短流動性好使用壽命長污染小等特點，主要用於修補轉爐迎鋼面通常稱「大面」也可以用於修補出鋼側，出鋼口及爐底等部位。
  16. In this study, advanced laser surface treatment, superplastic, solid - joint technologies were used to the bond of a - tial alloy to realize the high quality bond of this alloy at low temperature and short time

    本文將先進的激光表面處理，超塑成形，擴散連接工藝結合在一起，實現- tial合金低溫、短時、高質量的固態連接。
  17. The dissertation discusses some theories of computation including the unit stiff matrix of the spatial member in the local coordinates ， the coordinate transformation, the integration of the integer stiff matrix ， the equivalent joint load ， the introduction of the boundary condition ， the computation of the unit internal force and support reaction ， the stableness of the spatial stiff frame. the dissertation also discusses the methods of dealing with several unusual problems such as combined structure, temperature stress ， elastic bearing

    本文論述了空間桿件局部坐標單元剛度矩陣、坐標轉換、整體剛度矩陣的集成、等效結點荷載、邊界條件的引入、單元內力與支座反力計算、空間剛架穩定的計算理論，以及組合結構、溫度內力、彈性支承等幾個特殊問題的處理方法。
  18. 4 our company personally develops inner non - seal high - pressure rubber joint that can prevent effectively inner wall of rubber joint from the corrosion in the pipe of high - temperature resistance, acid and alkali resistance and oil resistance to improve the use life

    4我公司自主研發的內無縫高壓橡膠接頭，在耐高溫耐酸堿耐油的管道中更有效地防止了腐蝕性介質對橡膠接頭內壁的侵蝕，提高了使用壽命。
  19. In the result, the tensile stress which is produced because of temperature gap has been decreased or eliminated entirely. combined with some other measures, the construction and design for non - expansion joint of super - length structure has been carried out successfully

    從而不僅滿足了鋼筋混結構設計規范： 「如有充分依據和可靠措施，伸縮西安建築科技大學碩士學位論文縫最大間距可適當增大」的要求。
  20. This article incorporates with the practice for construction of mass concrete foundation structure of handan big world department store, according to the features in foundation structure design and the conditions of winter construction in this region, introduces micro - expansion concrete mix proportion design, pouring technology for mass concrete structure, the solution of the strengthen joint - strip and post - pouring joint strip in concrete foundation work, and temperature control for mass concrete

    結合大世界商城底板大體積混凝土的施工實例，針對基礎結構的設計特點和當地冬季施工的氣候條件，介紹了補償性混凝土配合比設計、大體積混凝土澆築工藝、基礎混凝土加強帶和后澆帶施工工藝、底板混凝土溫度控制和自動化監測等多項綜合性技術。
分享友人
分享到 Line

分享到臉書