terminal voltage 中文意思是什麼
terminal voltage
解釋
端子電壓-
Thus, the terminal voltage drops to zero.
這樣，路端電壓就降到零。 -
Low - voltage switchgear and controlgear for industrial use. mounting rails. top hat rail 15 mm wide for the fixing of terminal blocks. european standard en 50 045
工業低壓設備.支架型材.連接件固定用寬15mm端頭型材 -
Specification for low voltage switchgear and controlgear for industrial use - mounting rails - top hat rails, 15 mm wide for the fixing of terminal blocks
工業用低壓開關設備和控制裝置規范.安裝橫桿.固定接線板寬度為15mm的頂蓋橫桿 -
The bias magnetic field of the bias coil driven by bias current and small signal test current, results in the induced signal of the control coil. the terminal voltage of the control coil is detected by the test circuit. then the signal containing the information of rotor displacement is obtained, from which we can get the dc voltage signal proportional to the rotor displacement through half - wave rectification circuit and low pass circuit. this dc signal is put into a pid controller to get the control signal of the rotor displacement
偏置測試電路向偏置線圈輸入偏置電流和小信號測試電流，兩者產生的偏置磁場在控制線圈產生感應信號，檢測電路檢測控制線圈端電壓並提取含有轉子位移信息的電壓信號，該信號經半波整流電路和低通濾波電路后得到與轉子位移成正比例的直流信號，再由pid控制器轉換為轉子位移的控制信號，最後控制信號輸入功放電路產生控制電流，實現閉環控制。 -
The stability of electric power system has been being focused for a long time toprevent a power system from losing synchronism after sudden fault ， researchers have done much work and got many accomplishments this paper applied the direct feedback linearization ( dfl ) technique on the power system ， a strong nonlinear system simulation results by matlab proved this method efficiency main works and results are as follows ： this paper compared some existing methods in excitation control ， fast valve control and coordinated control respectively, analyzed the developments and actuality of nonlinear control research in brief, illustrated why ransient stability could be greatly improved by using the fast valve control in chapter 3 ， indicated the importance of coordinated control farther this paper introduced the inverse system theory, based on which ， discussed the dfl theory, pointed out which had consistency with the inverse theory, expanded the dfl theory combined the idiographic model equations ， made which adapt to the model of a single machine - infinite bus power system this paper referenced abundance articles and educed a set of equations ， which could describe the dynamical process of excitation and fast valve control for synchronous generators in the equations ， there were several very important parameters of power system - - rotor angle ( ) ， rotor speed ( ) ， generator q axis voltage ( eq ) ， transient voltage ( e ' q ) ， active power ( pe ) ， mechanical input power ( pm ) ， valve opening ( ) ， generator terminal voltage ( vt ) ， based on the model ， nonlinear coordinated controller and terminal voltage optimal controller have been designed by using the expanded dfl theory and lq optimal control theory the simulation results showed that the controller could keep power system transiently stable under the effects of a symmetrical 3 - phase short circuit fault ， which achieved better postfault regulation compared with another two routine methods ， one is the proportion excitation controller and proportion fast valve controller, the other is the proportion excitation controller and the optimal fast valve controller, which could exert good performance when met 1ittle disturbance either
在介紹逆系統理論的基礎上，詳細介紹了dfl理論，通過比較闡明了dfl理論其本質是逆系統方法的一類，並結合具體課題推導出的模型方程將dfl理論進行了擴展，使之適應于電力系統這個強非線性對象。通過參考大量的書籍文獻推導出一套實用的可將大型汽輪發電機勵磁與汽門綜合起來進行控制的模型方程，此模型方程涵蓋了電力系統中特別引人注目的幾個量- -轉子角、轉子轉速、發電機q軸電勢eq 、暫態電勢e ' q 、有功功率pe 、機械功率pm 、汽門開度、機端電壓vt ，在此基礎上建立了實用的電力系統簡化的數學模型，並將擴展的dfl理論應用於此模型系統，結合線性二次型最優控制理論設計出大型汽輪發電機的非線性綜合控制器及機端電壓最優控制器，通過模擬實驗與採用常規的按電壓偏差進行調節的比例式勵磁控制器+汽門比例控制及採用常規的按電壓偏差進行調節的比例式勵磁調節器和基於二次型性能指標設計的最優快控汽門（考慮發電機的飽和因素）進行了對比，證實了採用此種控制器可以有效地提高電力系統的暫態穩定性，並且在電力系統遭受小干擾時同樣具有良好的調節性能。 -
A commutator - brush combination is used as a mechanical rectifier to make the armature terminal voltage unidirectional and also to make the mmf wave due to the armature current fixed in space
通過使用換流器電刷的組合作為一個機械整流器以使得電樞的端電壓為單方向的同時也使得由電樞電流所產生的磁動勢在空間是固定的。 -
And the fuzzy control technology has been studied that reduce the stator terminal voltage to achieve higher power factor through testing power factor and using certain rules. the asynchronous motor intelligence operating control system plan design has been completed. simulation design and simulation experiment of the system has been carried on, and the simulation result indicated this intelligence control system has achieved the anticipated effect
在分析電機功率因數角的變化規律及功率因數角對晶閘管輸出電壓的影響的基礎上，提出了異步電動機在輕載或空載運行時通過檢測功率因數並經過一定規則降低定子端電壓來達到提高功率因數目的的模糊控制方法，完成了異步電動機節能運行控制系統的軟硬體設計，並進行了系統的模擬研究與實驗研究。 -
In chapter 2, the mathematical model of two - phase hybrid stepper motor as a generator is established. then according to the model, the functional relationship is obtained between the terminal voltage of stator winding and continuous rotor position
第二章，建立了二相混合式步進電機的發電模型，並進一步簡化得到定子繞組端電壓與轉子轉角之間的函數關系式，為步進電機實現連續角位移測量的研究奠定理論基礎。 -
Unified power flow controller ( upfc ) is one of the most powerful and most promising controllers of facts. if we use upfc to control the transmission parameters, terminal voltage, line impedance and phase angle in normal situation and use it to compensate zero sequence and negative sequence currents when one of transmission lines is cut off, we can implement two phases operating in high voltage transmission lines, which can improve stability and reliability for the transmission system
統一潮流控制器（ upfc ）是功能最強、最具發展潛力的靈活交流輸電系統（ facts ）控制器之一，如果在常規條件下，用upfc實現輸電線路的電壓調節、移相、潮流控制、阻尼振蕩等功能，在發生單相永久性接地或單相斷路故障時，由傳統的三相跳閘改為單相跳閘，用upfc的並補來濾除兩端系統的零序和負序電流，用upfc的串補來提高輸電線的傳輸功率，以實現兩相長期運行，那麼輸電系統的穩定性、可靠性將大大提高。 -
Based on a number of charging and discharging experiments, a thought is put forward that the polarization may be detected according to the terminal voltages at charging, terminal voltage at the short pause, and the soc ( state of charge ) ; the depolarization by momentary discharge according to the reference of optimal curve
在論文撰寫過程中，作者主要進行了如下方面的研究： -對鉛酸蓄電池的電化學機理進行充分研究，並在大量充放電實驗的基礎上，提出了依據蓄電池充電時和停充瞬間的端電壓和蓄電池荷電狀態檢測蓄電池極化狀況的思想。 -依據最佳曲線給定，採取瞬間放電減少極化。 -
The relation between terminal voltage and terminal current is called a terminal characteristic.
輸出埠電壓和輸出埠電流間的關系稱為外特徵。 -
The chip jk3ce that is one of micro - controllers in motorola 68hc08 family is used as control unit in this system. the zero crossing point of the back emf can be obtained by comparing the terminal voltage with the virtual neutral point, then using the software of the system can figure out the commutation period. the electronic commutation replaces the mechanical commutation in this way
本系統採用的控制晶元為motorola系列單片機中的jk3ce ，反電勢過零點可以通過比較電機端電壓和虛擬中點電壓來得到，將過零點信號送往單片機捕捉埠後由系統軟體來確定換相時刻，這樣就可以由電子換向裝置替代機械換相裝置，有利於提高系統運行的可靠性，並降低了系統維護的費用。 -
The dc static high voltage meter is the main instrument for measuring the terminal voltage of the insulators
摘要直流高壓靜電電壓表是測量絕緣電阻表端電壓的主要設備。 -
Controls to hydro - generator is include manipulation of the rotational speed or freguency, output active power from hydraulic turbine, generator terminal voltage and the reactive power exporting from the generator
對水輪發電機組的控制包括機組轉速即頻率、水輪機輸出功率、機端電壓和發電機輸出無功功率等的控制。 -
Method for measurement of radio interference terminal voltage of lighting equipment
照明設備無線電干擾終端電壓的測量方法 -
Regard how to structure the control system of sensorless bldcm with dsp - tms320f240 as the centre in this paper, the detailed argumentation course of the motor startup, bemf terminal voltage measurement and control strategy is given out, give and pay concrete details for the software and hardware realization and experimental result. in order to treat the bldcm control system with dsp clearly, the full paper divides into six chapters altogether : chapter one, introduceing the development course, the structure characteristic and operation principle, etc. of bldcm in the introduction ; chapter two, directed against the startup issue of bldcm, the chapter give and publish the rotor measure pulse orients technology for motor startup in detail ; chapter three, proceed with mathematics model of the bldcm, expounding the control schemes ; chapter four, two important devices introducing : dsp ( 240 tms320f ) and power invertor control chip ( ir2131s ) ; chapter five, give and publish the detail of hardwares of control system ; chapter six, by ccs ide of ti, realize the control schemes in the front chapters with software, offere the procedure flow chart of main subroutine and some key place of programming, the experiment result in addition
全文共分六章：第一章、緒論中介紹了bldcm的發展歷程、電機本身的結構特點和工作原理等；第二章、針對五位置傳感器bldcm的起動問題，文中詳細給出了檢測脈沖轉子定位起動技術；第三章、從電機的數學模型入手，詳細論述了反電動勢端電壓法和系統的控制策略；第四章、介紹了硬體實現中的兩個重要器件： dsp （ tms320f240 ）和功率管逆變器控制晶元（ ir2131s ） ；第五章、詳細給出了控制系統的硬體實現細節；第六章、利用ti提供的ccs集成開發環境，將前面章節的控制方案用軟體加以實現，給出了主要部分的程序流程圖和一些編程要點以及實驗結果。 -
Symmetrical terminal voltage
終端平衡電壓 -
Ganfa has over 50 years experience of designing and manufacturing and has many items of patent techninque. the synchronous generators and permanent magnet generators which are manufactured with advanced technology and excellent machining equipement, will be able to meet the requirement of different technical condition which matched with various type turbines. ganfa has manufactured the generators of 0. 1 to 20mw in capacity which have been put into operation at present and owns the capability to manufacture the following generators : the capacity per unit up to 180mw, the stator outer diameter of generator up to 9, 000mm, the speed of vertical type generator up to 750r min, and thespeed of horizontal type generator up to 1, 500r min, both the b - grade and f - grade insulation class, the terminal voltage can up to 13. 8kv. ganfa manufactured 34, 500kw water turbine generator sets for the donghewan power station, yongchang, gansu, china which is located in 2. 868. 5m height above sea level, and has successfully solved the difficult problems such as plateau corona - shielding. ganfa is equipped with the generator test station and insulation material laboratory which are advanced test facilites and testing means to make each item electrical performance of products meet designing requirements from purchasing to delivering
公司具有50年的設計製造經驗，擁有多項專利技術，生產的同步發電機永磁機技術工藝先進，製造精良，能滿足與各式水輪機配套的不同技術條件要求。目前公司已製造投產的發電機容量范圍為0 . 120mw ，具備生產單擊容量50mw的能力，發電機機座號最大可達9000mm ，立式機最高轉速750r min ，臥式機最高轉速達1500r min ，絕緣等級有b級和f級，圈式線圈最高電壓達13 . 8kv ，公司製造的甘肅永昌東河水電站34500kw水輪發電機組，海拔為2868 . 5m ，成功解決了高原防暈等難題。公司擁有電機試驗站絕緣材料試驗室等先進的實驗室設施和測試手段，使產品從原材料進產，到成品出產的各項電器性能測試均能滿足設計要求。 -
Asymmetrical terminal voltage
終端不平衡電壓 -
During the process of numerical calculation of electromagnetic, the stator terminal voltage is set as restriction condition and the starting current is iterated in order to obtain the starting current and starting torque under the rating voltage. finally, the calculated results and measured results are compared to test that the calculation of starting performance can agree with the need of practical engineering project
在電磁場的數值計算過程中，以定子端電壓為約束條件，對定子起動電流進行了迭代計算，得到了額定電壓下的起動電流和起動轉矩，最後把正弦電磁場計算結果與實測結果進行了對比，表明復合籠條轉子感應電動機起動性能的計算結果滿足工程實際的需要。
分享友人