thermal probe 中文意思是什麼
thermal probe
解釋
熱探頭-
Potash micatization is one of the main hydrothermal alteration minerals genetically related to the lead - zinc - silver deposit. it usually shows as muscovitization, sericitization and illitization. this paper presents a comprehensive study on the chemical composition of potash mica, adapted the follow methods : electronic probe, differential thermal analysis, x - ray diffraction analysis. at last, the structu ral characteristics and the geological environment of potash mica forming have been discussed
系統地研究了鉀質白雲母化的礦物組成，採用了電子探針差熱分析x射線分析等技術方法，探討了鉀質白雲母的結構特徵和形成的地質環境及找礦意義。 -
Again reported that the centre combined adrenaline injection and the thermal method of heater probe in treating bleeding peptic ulcers
隨后，中心再改良治療方法，並成功以熱探頭配合腎上腺素注射來治療胃出血，效果良好。 -
Standard test method for determination of thermal conductivity of soil and soft rock by thermal needle probe procedure
熱針探頭法測定土壤和軟石導熱性的標準試驗方法 -
A new thermal probe method for determining thermal conductivity based on the minimal dispersion of thermal diffusivity
據熱擴散率最小離散度確定導熱系數的新熱探針法 -
Study on probe to measure thermal conductivity of food materials at low temperature
探針法測量低溫下食品導熱系數研究 -
Study on thermal conductivity probe for thermal conductivity of artery at low temperature
探針法測量低溫下豬主動脈導熱系數研究 -
In this paper, firstly, monolithic materials cosb3 and bi2te3 were prepared by sparkle plasma sintering ( sps ) respectively, and at the same time the microstructure of cosb3 and bi2te3 were studied by sem ; the seebeck coefficients and electrical conductivities of monolithic materials were measured by standard - four - probe method ( ulvac zem - 700 ) in a he atmosphere simultaneously, and their thermal conductivities were investigated by laser flash method ( tc - 7000 ) in vacuum. secondly, the junction temperature of graded bi2te3 / cosb3 thermoelectric materials was optimized based on the thermoelectric transport properties of monolithic materials, also when graded materials were used in the temperature difference ranging from 300k to 800k, the length ratio of monolithic materials cosb3 and bi2te3 were optimized in theory. thirdly, graded bi2te3 / cosb3 thermoelectric materials were prepared by two - step sps sintering, and the relationship between its average seebeck coefficients and temperature were calculated by theory mo del
均質材料cosb _ 3和bi _ 2te _ 3的電導率和seebeck系數採用標準四端子法于he氣氛下在zem - 1上同時進行測量；熱導率採用激光微擾法（ tc - 7000 ）于真空狀態下進行測量；其次，在對均質材料cosb _ 3和bi _ 2te _ 3熱電傳輸特性研究的基礎上，對結構梯度bi _ 2te _ 3 cosb _ 3熱電材料的界面溫度進行了優化；為了使結構梯度bi _ 2te _ 3 cosb _ 3熱電材料在300k至800k的溫度范圍內具有最佳的熱電性能，本研究同時對梯度結構熱電材料當中均質材料cosb _ 3和bi _ 2te _ 3材料的長度進行了優化設計；第三，通過兩步放電等離子燒結的方法制備出了結構梯度bi _ 2te _ 3 cosb _ 3熱電材料；採用理論計算的方法研究了梯度結構熱電材料平均seebeck系數和溫度的關系；同時為了驗證設計的結果，本論文對結構梯度bi _ 2te _ 3 cosb _ 3熱電材料的開路輸出電壓和熱端溫度之間的關系及梯度材料在300k至800k的溫度范圍內使用時的功率輸出進行了相應的研究。 -
Therefore, m4 - 0132 - water and m1 - 0001 - ethanol are good adsorption working pairs in the process of adsorption refrigeration driven by solar energy and low - grade thermal energy. ( 2 ) apply the related mechanism analysis method used in catalyst to the mechanism research in composite adsorbents. a new way of research is put up here, in which the pyridine is used as probe compound, and
對本文研究的製冷工質對的製冷工況分析結果表明:自製復合吸附劑m4一01犯一水和ml一0001一乙醇適用於空調等大循環量的製冷系統， ml一9906一乙醇和mz一0003一乙醇可用於製冰和冷凍等需要低溫的製冷場所。 -
The components and strcture of turquoise are studied deliberately through electron probe, x - rays powder diffraction and differential thermal analysis ( dta )
通過電子探針分析、 x射線粉晶衍射和差熱分析對綠松石的成分和結構作了深入研究。 -
Sapphire fiber thermal probe based on wavelet transform
基於小波變換的藍寶石熒光光纖溫度計 -
Fabrication of nanostructures based on spm as an extension to spm imaging, referred to as scanning probe nanofabrication ( spn ) is an emerging technique undertaken at labs in the past ten years that comprises manipulation of atom or molecule in a bottom - up paradigm and scanning probe lithography ( spl ) in a top - down paradigm. in chapter one, in the light of decentralized experimental data in this respect, the author, classify in an analytic approach the literature concerned as electrical spl, mechanical spl, thermal spl, and optical spl in terms of different mechanisms of interplay between a probe and a surface of a sample, after describing the most important of this type of microscopy, i. e., scanning tunneling microscopy and atomic force microscopy
由於這項技術的實驗數據比較分散，因此，作者在論文的第一章里首先介紹了掃描探針顯微鏡的兩個最重要的類型，即掃描隧道顯微鏡和掃描原子力顯微鏡的工作原理；然後根據加工方式的不同把它分為自下而上的掃描探針原子（分子）操縱與自上而下的掃描探針刻蝕兩大類；而根據掃描探針與樣品的不同作用機理，對掃描探針刻蝕加工又進行了歸納與綜述，對其特殊的加工方法作了原理性的介紹，並分析了目前存在的共性問題與應用前景。
分享友人