thickness flexure 中文意思是什麼
thickness flexure
解釋
厚度彎曲-
Yinggete - bagemaode metamorphic core complex belt with three - layer construction is put forward, which evolved from late jurassic to cretaceous. the extensional simple shear model of the chagan fault depression is established. the tectonic evolution and the dynamics character of chagan fault depression and its adjacent mesozoic - cenozoic basins are discussed : at the end of triassic continental orogeny increased crust thickness crust uplift and denudation were happened ; jurassic was a period of local partly extensional collapse of erogenic belt and cretaceous was a period of widely extensional collapse of postorogenic erogenic belt ; cenozoic was a period of the development of stable intracontinental depression with the character of long distant collision response and weaked compression flexure
討論了查干凹陷及鄰區中-新生代盆地構造演化及其地球動力學特徵，三疊紀（印支期）為陸內造山作用與地殼增厚、隆升剝蝕階段；侏羅紀（燕山早期）為造山後造山帶的局部伸展垮塌階段；白堊紀（燕山晚期）為造山期后大規模伸展垮塌作用與伸展盆地的發育階段；新生代（喜山期）為遠距離碰撞效應與弱擠壓撓曲性質的穩定大陸內坳陷的發育階段。 -
The minimum reinforcement rate has little effect on reinforcement in columns. ( b ) when considering the bars in slab participate in beams against negative flexure, four or six times slab - thickness on each side of web can be defined as the effective flange width of slab by intermediate or rare earthquake actions
當考慮板筋對梁端負彎矩承載力的提高作用時，可在設防烈度地震和罕遇地震作用下分別取每一梁側四倍、六倍板厚范圍作為板的有效寬度。 -
Neglecting the influence of concrete stress - path, relative program is presented to make full - process analysis on compression - flexure members confined with cfrp in the compression zone, a key research is to analyze the effect of some parameters including axial compression ratio, thickness of cfrp, concrete strength on strength capacity and displacement ductility of reinforced compression - flexure members
在忽略混凝土應力路徑的影響下，編制相應程序對碳纖維布粘貼鋼筋混凝土壓彎構件進行了全過程分析及相關參數研究，並把計算結果與試驗結果進行了對比，兩者吻合較好。 -
The result illustrates that the residual thermal stress of the tz - 3y20a / mo multiplayer composite is less than the flexure strength of tz - 3y20a ceramic at the same experimental condition when the layer number and layer thickness " ratio exceeds 27 and 2 respectively
結果表明，當疊層材料層數和層厚比分別超過27和2時，計算得到的殘余應力小於tz - 3y20a陶瓷的抗彎強度。 -
The testing results of the flexure strength and fracture toughness of multilayer samples show that, the flexure strength of rectangular bars of samples achieves the maximum ( 737. 1mpa ) when the layer thickness of tz - 3y20a is 200um and the layer thickness of mo is 67um
試樣彎曲強度和斷裂韌性的測試結果表明，當tz - 3y20a層厚度為200 m ， mo層厚度為67 m時，疊層材料的抗彎強度達到最大值（ 737 . 1mpa ） 。
分享友人