thread ends 中文意思是什麼
-
Fold chenille stems in half and thread the ends into the holes in each base, leaving a small loop sticking out
將繩絨線對折,然後將其兩端穿入紙杯底部的兩個孔內, (繩絨線彎折處的)線圈應該(在杯外)留出一小段。 -
When the glue is set, remove the pins or clamps, trim the bare ends of the feather and bind them with thread for extra safety
當膠是的時候放置,除去大頭針或螺絲鉗,整齊羽毛的赤裸結束而且為額外的安全用綁他們線。 -
Taper pins with thread ends and constant taper lengths
帶固定錐形長度和螺紋端頭的錐形銷 -
Threads and thread ends for wood screws
木螺釘用螺紋和螺紋端 -
Sockets for screwed ends with metric fine thread and whitworth pipe thread
公制細螺紋和惠氏管螺紋管接頭用分岔接管 -
Center holes 60 with thread for shaft ends for rotating electrical machines
旋轉電動機械用軸端帶螺紋的60度中心孔 -
Fcd. 3 138b : 4ds outer - thread copper pipe union at both ends of the inlet and the outlet
Fcd . 3 138b :進水口出水口兩端為4分15外螺紡銅管接頭 -
Fcd. 3 138c : 4ds outer - thread copper pipe union at both ends of the inlet and the outlet
Fcd . 3 138b :進水口出水口兩端為4分15外螺紡銅管接頭 -
Conical shaft ends with internal thread ; dimensions
有內螺紋的錐形軸端.尺寸 -
Conical shaft ends with external thread ; dimensions
帶外螺紋的錐形軸端.第1部分:尺寸 -
Rod ends, adjustable, self - aligning plain bearing with self - lubricating liner and threaded shank with engagement : 1. 5 thread - dimensions and loads
帶自潤滑套和嚙合量為1 . 5的螺紋軸的可動調自定位滾動軸承桿端.尺寸和負載 -
Rod ends, adjustable, single fork and threaded shank with engagement : 1. 5 thread diameter - dimensions and loads
嚙合量為1 . 5螺紋直徑的單叉螺紋柄可調節的連桿端頭.尺寸和負荷 -
Rod ends, adjustable, double fork and threaded shank with engagement : 1. 5 thread diameter - dimensions and loads
嚙合量為1 . 5螺紋直徑的雙叉螺紋柄可調節的連桿端頭.尺寸和負荷 -
Aerospace series ; rod - ends, adjustable, single fork and threaded shank with engagement : 1, 5 thread diameter ; dimensions and loads ; german version en 2791 : 1991
航空航天系列.嚙合長度為螺紋直徑1 . 5倍的螺紋桿和單 -
Aerospace series ; rod - ends, adjustable, double fork and threaded shank with engagement : 1, 5 thread diameter ; dimensions and loads ; german version en 2792 : 1991
航空航天系列.嚙合長度為螺紋直徑1 . 5倍的螺紋桿和雙 -
En 2792 aerospace series. rod ends, adjustable, double fork and threaded shank with engagement : 1, 5 x thread diameter. dimensions and loads
航空航天系列.帶自潤滑油封和螺紋安裝桿的雙包邊可調接頭.螺紋直徑1 . 5 .尺寸和負荷 -
En 2791 aerospace series. rod ends, adjustable, single fork and threaded shank with engagement : 1, 5 x thread diameter. dimensions and loads
航空航天系列.帶自潤滑油封和螺紋安裝桿的單包邊可調接頭:螺紋直徑1 . 5 .尺寸和負荷 -
B connections for general use and fluid power - ports and stud ends with thread - stud ends with metal - to - metal sealing type b
液壓管接頭用螺紋油口和柱端金屬對金屬密封柱端 -
If the thread ends before the timeout,
如果線程在超時之前結束,則 -
Aerospace ; runouts, undercuts and thread ends for mj - threads to din iso 5855
航空和航天.符合din iso 5855的mj螺紋的螺紋尾空刀
分享友人