thread error 中文意思是什麼

thread error 解釋
螺紋誤差
  • thread : n 1 線；細絲；〈英國〉麻紗，〈美國〉棉紗；纖維。2 細線，細流，細礦脈。3 （議論等的）思路，條理，...
  • error : n. 1. 錯誤；失錯。2. 謬見，誤想；誤信；誤解。3. 罪過。4. 【數學】誤差；【法律】誤審，違法；（棒球中的）錯打。adj. -less 無錯誤的，正確的。
  1. If a programming error in thread b causes it to call

    如果線程b中發生了一個編程錯誤，導致它調用
  2. If a thread has memory problems, the most likely cause is programming error, such as infinite recursion

    如果某個線程有內存問題，則最可能的原因為編程錯誤（如無限遞歸） 。
  3. Thirdly, the paper builds parameter arithmetic model based on the middle line. we get the middle line from two interpolations, and give the compute course of the main parameters. in this way, we can avoid the phase error and thread side error what the single probe system cannot escape

    第三，建立了基於中徑線的參數演算法模型，利用二次插補擬合中徑線，並在此基礎上給出了各主要參數的計算過程，從而解決了基於理論齒型的演算法因濾波失真和牙型角誤差而帶來的數據處理誤差問題。
  4. Debugging error : " illegal cross - thread operation : control control name accessed from a thread other than the thread it was created on.

    調試錯誤： 「非法的線程間操作:從不是創建控制項control name的線程訪問它。 」
  5. This update addresses the " stop 0x0e3 error occurs when redirector thread tries to release a lock " issue in windows 2000

    此更新解決windows 2000中「當重定向器線程試圖釋放鎖定時發生的終止0x0e3錯誤」的問題。
  6. If there is no managed code on the thread currently in context, the hresult sos e nomanagedcode is returned with a facility value of 0xa0 and an error code of 0x1000

    如果上下文中當前在該線程上沒有託管代碼，則hresult sos _ e _ nomanagedcode以功能值0xa0以及錯誤代碼0x1000返回。
  7. With tiger, you get a shared data archive, new thread scheduling algorithms, and a fatal error handler for those times when things don t go well

    Tiger提供了共享的數據檔案文件、新的線程調度演算法以及致命錯誤處理器（用來處理故障） 。請在本文附帶的
  8. Receives the error code, number of bytes, and overlapped value type when an i o operation completes on the thread pool

    當i / o操作在線程池上完成時接收錯誤代碼、位元組數和重疊值類型。
  9. This update addresses the " stop 0x0e3 error occurs when redirector thread tries to release a lock " issue in windows 2000, and is discussed in microsoft knowledge base article 810038

    此更新解決windows 2000中「當重定向器線程試圖釋放鎖定時發生的終止0x0e3錯誤」的問題，在microsoft知識庫（ kb ）文章810038中有相關論述。
  10. Lead error would be occurred during process thread by nc lathe. aiming at this issue, accurate thread excess was calculated. this way is simple and effectiveness in practice

    摘要用數控車床加工精密螺紋時，在開始段和結束段會出現導程誤差。針對這個問題，進行了準確的螺紋裕量計算。在實際加工中，簡單易行，效果良好。
  11. Fir digital filter is programmed with window function method in the filter module and the thread design method is used to process data, which improves the system real - time. in the end the paper gives the error analysis and points out the error source in the course of data processing

    在濾波器模塊程序設計中，採用窗函數法，用軟體編寫了fir數字濾波程序，實現數字濾波功能，並把線程設計方法應用於數據處理，提高了系統實時性；在本文結尾給出了數字化數據處理誤差分析，剖析了誤差的來源。
分享友人
分享到 Line

分享到臉書