time gears 中文意思是什麼
time gears
解釋
定時齒輪系-
You remember the first time we dropped gears in this one
還記得我們第一次開這個車的情景嗎？ -
It is the first time in china to set the speed increase gears form in the new compressor and to adopt several new techniques including the condenser with oil - separator built - in, jet exhauster and electrical expansion valve used to supply liquid for the flooded evaporator in the unit
本壓縮機在國內首次採用了帶增速齒輪的形式，冷水機組在國內內首次採用了內置油分冷凝器、引射器和電子膨脹閥對滿液式蒸發器供液等新技術。 -
At the same time, the system vibration also made the paired gears enter into meshing in advance or and seceding of a couple of laggingly
同時，系統振動還使嚙合齒對提前或遲后進入嚙合、提前或遲後退出嚙合。 -
On the basis of the engage efficiency and lubricious conditions, theoretical transmission efficiency with the different drive ratios ( 1 / 50 and 6 / 31 ) of involute cylinder worm gears is analyzed. at the same time, the change trend of engage efficiency and transmission efficiency with different design parameters is discussed. the experimental investigation on transmission efficiency
從漸開線蝸輪蝸桿傳動的嚙合效率和潤滑條件兩個方面對不同傳動比的漸開線圓柱蝸桿的傳動效率進行理論分析，並通過傳動比分別為1 / 50和6 / 31的漸開線圓柱蝸桿設計參數得到蝸桿潤滑條件的理論分析結果和蝸桿嚙合效率、傳動效率的變化趨勢，同時利用電測法對蝸桿傳動的傳動效率、潤滑油平衡溫度進行測試，將測試數據與理論計算結果進行對比分析，得出理論分析結果的正確性。 -
The paper describes the feature of double circular arc spiral bevel gears, basing on such gears manufacture theory, the paper depicts how to form the double circular arc spiral bevel gear tooth profile, at the same time, depicts its meshing theory and derives its tooth profile equation. basing on fsh short tooth, the paper derives the tooth depth equation, describes its manufacture technology, makes out this tooth propile single side method regulation calculation card
本文從弧齒錐齒輪加工原理出發，闡述了雙圓弧弧齒錐齒輪副點嚙合齒面的形成原理，同時還論述了雙圓弧弧齒錐齒輪基本嚙合原理，推導出了具有普遍形式的齒面方程，同時以fsh短齒形為藍本還推導出了雙圓弧弧齒錐齒輪齒厚計算公式，闡述了雙圓弧弧齒錐齒輪的製造工藝，編制了雙圓弧弧齒錐齒輪單邊切削法機床調整計算卡。 -
This paper gives the way of using the ac servo drive instead of the traditional drive mode consisted of the main motor, the gears and belts, realizing the synchronous drives of the multi - motors. the closed loop control technology of the speed and the position embedding has been adopted to track in real time, then to reduce the transmission error and the noise, so as to increase the control precision and the stability of the combination and simplify the maintenance and repair of the mechanical and technical system
採用交流伺服驅動代替傳統的由主電機、齒輪和皮帶組成的傳動方式，實現多電機同步驅動;採用速度環和位置環嵌套的閉環控制技術，進行實時跟蹤，達到減小傳動誤差、減小噪音，增強機組的控制精度與穩定性、簡化機電系統的維護與修理的效果。 -
The durable semi - enclosed tail rotor gearbox protects the tail rotor gears while at the same time allowing easy inspection
耐用的半封閉式保護尾槳尾旋翼變速箱齒輪同時允許容易查閱
分享友人