tooth bending stress 中文意思是什麼

tooth bending stress 解釋
輪齒彎曲應力
  • tooth : n （pl teeth）1 牙齒。2 齒狀突出，輪齒，鋸齒，耙齒（等）。3 嗜好。4 〈常 pl 〉（像牙齒那樣能咬人...
  • stress : n 1 壓力，壓迫，緊迫，緊張。2 【語音】重音；重讀；【詩】揚音；語勢，著重點。3 重要（性），重點，...
  1. Abstract : the therortical calculation of the bending stress of the root and experimental stress analysis on the modified profile and the standard involute tooth profile were made with the finite element method and the electric resistance strain film method. this indicated that the modified profile was supe rior to the standard involute profiles in terms of the bending strength

    文摘:分別用有限元和電阻應變片法對修形齒形和漸開線齒形進行齒根彎曲應力計算與實驗應力分析.結果證明在彎曲強度方面修形齒形比標準漸開線齒形更優越
  2. Among the results of these researches, cylindrical gears with curvilinear tooth trace have merits as follows : higher bending stress, low noise, better lubrication conditions, and no thrust forces. so this kind of gear can be considered to substitute the helical gear and herringbones

    本文提出的弧齒線圓柱齒輪是一種新型齒輪傳動形式，具有傳動平穩、噪聲低、潤滑性能良好、輪齒彎曲疲勞強度大的特點，因此該齒輪可以作為斜齒輪和人字齒輪的替代品用於高速重載場合。
  3. A calculation research on the tooth root bending stress of asymmetrical involute gear

    非對稱漸開線齒輪齒根彎曲應力的計算分析
  4. The influence law of gear ' s bending stress affected by nominal pressure angle and technological angle of tooth profile has been summarized and obtained a conclusion that the maximum bending stress before running in period occurred at the waist place of the tooth, thus provided a theoretical foundation for the design and application of double arced gears

    總結了名義壓力角和齒形工藝角對輪齒彎曲應力的影響規律，並得出跑合前最大彎曲應力發生在齒腰處的結論，為雙圓弧齒輪的設計和使用提供理論依據。
  5. Compared with the traditional cantilever structure, the bearing life of two - terminal bracing structure is improved by 17. 51 times, while the contact stress of gear tooth is reduced by 45. 7 %, and the bending stress of gear tooth is reduced by 62. 8 %

    與傳統主動齒輪懸臂結構相比兩端支撐結構的軸承壽命提高了17 . 51倍、輪齒接觸應力降低45 . 7 % 、輪齒齒根彎曲應力減小62 . 8 % 。
  6. Considering the time - variant mesh stiffness, the calculated results demonstrated the change of tooth root bending stress in one engagement period

    計算結果揭示了由於時變嚙合剛度的影響齒根彎曲應力在一個嚙合周期的變化規律。
  7. The calculation of tooth contact stress and the bending stress is discussed. the equation of the bending stress of the gear is developed and the arcuate domino effect is analyzed, comparing with ordinary involute gears

    本文研究了弧齒線圓柱齒輪的齒面接觸應力和彎曲應力的計算方法，提出了計算彎曲應力的公式，對輪齒彎曲效應的影響進行了分析，並與直齒圓柱齒輪進行了比較。
分享友人
分享到 Line

分享到臉書