tooth size 中文意思是什麼

tooth size 解釋
牙齒大小
  • tooth : n （pl teeth）1 牙齒。2 齒狀突出，輪齒，鋸齒，耙齒（等）。3 嗜好。4 〈常 pl 〉（像牙齒那樣能咬人...
  • size : n 1 大小，尺寸規模身材。2 （鞋帽等的）尺碼，號；（紙張的）開。3 巨大，大量；相當大的分量。4 〈口...
  1. In clinic, we often can find out many patients who have teeth irregularly and malocclusion caused by intermaxillary tooth size discrepancy

    在臨床上，我們常常可以見到因為顎間牙齒大小的差異，導致牙齒排列不整齊的病人和異常的咬合。
  2. For an orthodontic case with the discrepancy of the discoordination between the length of palate bone and tooth size or for a case with skeletal discrepancy of the unsymmetry upper and lower jaw in their size and position, the most common treatment is to extract the upper ahd lower first or the second premolar

    摘要一般矯正治療，對于齒槽骨和牙齒大小長度總和的不調和或上下顎骨骨骼性大小、位置不對稱，其處置原則通常都以上下顎第一小臼齒或第二小臼齒等4齒做為拔除對象來進行矯正治療。
  3. Size and obliquity of tooth directly influence clutch whether normal operating. it is a key part for ensuring normal operating of aira too. this article fully deduces their compute formula

    該齒形的大小、傾角直接影響離合器是否能正確地嚙合和分離，也是保證機構進行正確工作的關鍵部分，本文詳盡推導了它們的計算公式。
  4. Water system. 45 degree saw - tooth thread. tooth pattern and basic size

    水系統. 45鋸齒形螺紋.牙型與基本尺寸
  5. Intermaxillary tooth size discrepancy can affect the final result of orthodontic treatment and its stability

    而顎間牙齒大小的差異，可能會影響矯正治療最後的結果和咬合的穩定性。
  6. First, the basic theory of static load sharing mechanism has been presented, mainly including manufacturing and assembly error of each gear component ' s axis and each bearing ' s axis, gear size ( tooth thickness ) errors, simultaneous error of middle two - tooth. the formula of equivalent mesh error has been deduced, the load sharing coefficient has been computed. second, the influences of each error on the static load sharing coefficient have been discussed

    首先，從靜力學的角度研究了星型齒輪系統均載的基本原理；確定了影響齒輪系統均載特性的製造和安裝誤差，主要包括：各個齒輪構件的中心軸線製造和安裝誤差、軸承中心軸線的製造和安裝誤差、齒厚偏差、雙聯星輪同時嚙合線誤差；推導了這些誤差的當量嚙合誤差的計算公式，分析了系統的均載特性。
  7. Dentists and researchers have come up with the formula for the perfect smile, from the size and width of each tooth to the curve, colour and shape of the teeth, and the overall width of the smile

    牙醫師和研究人員提出了完美笑容的黃金比例，從每個牙距離彎曲的尺寸、寬度、牙齒的顏色、形狀及微笑是的寬度。
  8. This paper calculated total co ntact line length of worm pair by using the knowledge of the spatial - engaging - principle and numerical quadrature metheod, and put forward a concept of variati on coefficient of total contact line length, and found out the actual size of co ntact area of tooth surfaces

    運用空間嚙合原理等知識和數值積分的方法計算了蝸桿副接觸線總長度，並提出了接觸線總長變動因數的概念，求出了齒面實際接觸區域的大小。
  9. Wgp type barreled tooth flank coupling with barking disk data and size table2

    Wgp型帶制動盤鼓形聯軸器參數與尺寸表1
分享友人
分享到 Line

分享到臉書