trough angle 中文意思是什麼

trough angle 解釋
槽角
  • trough : n 1 木盆；馬槽，豬槽；承溜；水筧；洗礦槽。2 （麵包店的）揉面盆，面缽。3 【航海】（深6000米以上的...
  • angle : n 【英史】盎格魯人〈cf Angles〉。n 1 角，隅，角落；棱，嬗角。2 【數學】角，角位，角的度數。3 【機...
  1. Fluid noise mainly comes from out put pulsation of rate of flow, the main reason of out put pulsation of rate of flow is the instant high pressure return flow that obturation cubage produced when the big round curve pressure transition. the v trough on the port plate can reduce the fluid noise. in this paper, the author based on the acting of dam a river and condensability of liquid and used matlab language as tool to calculate the v trough on the original port plate and drew out the p - t diagrammatic curve and analyzed its shortcoming and improved the design of original v trough and got that the best size of its angle was 12. 3 and its length was 5mm and the cross section was an equilateral triangle

    流體噪聲主要來源於輸出流量脈動，造成輸出流量脈動的主要原因是閉死容積在大圓弧段壓力切換時產生的瞬時高壓迴流，在配流盤上開設v型尖槽可降低因高壓迴流而引起的流體噪聲，本文以截流作用和液體的可壓縮性為理論依據，以matlab語言為工具，對原配流盤上的v型尖槽進行了理論計算，繪制出p - t圖線，分析了它的不足，並對原有v型尖槽進行了優化設計，得出了v型尖槽的最佳幾何尺寸：配流盤平面上的v型尖槽的兩邊的夾角為12 . 3 ，槽長5mm ，槽的橫截面為等邊三角形。
  2. Play well an arbitrary signal is divided into three steps : 1, angle control with the mouse to determine the mouse point and click ; 2, the mouse ball kicked to choose the location red circle is to be kicked, click the mouse confirmed ; 3, the screen showed strength among planters, the more strength trough forces on the right and the greater good time, the clicking of the mouse shoot

    踢好一個自由球分為三個步驟： 1用鼠標控制角度，確定角度后單擊鼠標2鼠標在球上選擇要踢的部位圓圈為紅色才是可以踢的，單擊鼠標確定3屏幕中間顯示力量槽，力量槽越往右力量就越大，看好時機，點擊鼠標射門。
  3. In this way, when obturation cubage leave absorb oil cavity it connects the eduction oil cavity with the v trough and with the increasing of the turning angle, the size of the cross section of v trough become bigger and bigger, which make the pressure between the cavity of two blades much higher and higher, and until it completely connects the eduction oil cavity, it reaches the pressure of the eduction, and it can effectively reduces the fluid noise caused by high pressure return flow

    這樣，當密閉容積離開吸油窗口之後，通過v型尖槽逐漸與排油窗口連通，隨著轉角的增加， v型尖槽通流截面積逐漸增大，這就使兩葉片間容腔內的壓力逐漸升高，直至完全接通排油窗口時，才升壓達到壓油腔的壓力，這樣可以有效地降低因高壓迴流而引起的流體噪聲。
分享友人
分享到 Line

分享到臉書