tube socket 中文意思是什麼
tube socket
解釋
電子管座-
Copper tube fittings for construction spigot and socket joint
建築用銅管管件 -
When flux appears liquid and transparent on both tube and valve, start sweeping flame back and forth along axis of joint to maintain heat on parts to be joined, especially toward base of valve socket
當焊劑變成液態並且在管道和閥門上呈現半透明狀態時，開始將火焰沿著連接部件的軸線進行進退烘烤，以保持連接部件、特別是閥門套筒底座部位的熱度。 -
Apply brazing wire or rod at point where tube enters valve socket
將銅焊線或銅焊條按在插入閥門承插口的管道線上。 -
Silver brazing method : apply brazing wire or rod at point where tube enters valve socket
銀釬焊法：將焊線或焊桿點在閥門里的管道套座上。 -
Assemble joint by inserting tube into socket hard against the stop
在進行連接組裝時，要將管道插入管套直到遇到阻擋為止。 -
When flux appears liquid and transparent on both tube and valve, start sweeping flame back and forth along axis of joint to maintain heat on parts to be joined, especially toward the base of the valve socket
當管道和閥門上的焊劑都變成液狀和透明時，則開始沿著連接軸向前後來會掃著火焰，保持連接部件的溫度，特別是閥門承插口底部的溫度。 -
Plugs, socket - outlets and couplers for industrial purposes - part 2 : dimensional interchangeability requirements for pin and contact - tube accessories
工業用插頭插座和耦合器.第2部分:插銷和插套附件的尺寸互換性要求 -
Plugs, socket - outlets and couplers for industrial purposes - part 2 : dimensional interchangeability requirements for pin and contact - tube accessories ; german version en 60309 - 2 : 1999 a11 : 2004
工業用插頭插座和耦合器.第2部分:插銷和插套附件的 -
Plugs, socket - outlets and couplers for industrial purposes - part 2 : dimensional interchangeability requirements for pin and contact - tube accessories iec 60309 - 2 : 1999 ; german version en 60309 - 2 : 1999
工業用插頭插座和耦合器.第2部分:插針和插套附件的 -
Various successive partial plastic forming methods for processing groove, including thread rolling, cross rolling and skew rolling, splitting, rolling of spline shaft, split rolling, open - die extrusion of spline shaft / gear, extrusion of internal screwed tooth socket parts with large helical pitch, integral cold forging for slot commutator, extrusion - ploughing for outside fin tube, drawing of tube with spiral internal / external ribs etc. have been introduced briefly
摘要介紹了用於加工槽的各種連續局部塑性成形方法，包括螺紋軋制、橫軋與斜軋、分劈、花鍵軸滾軋、劈分軋制、花鍵軸齒輪開模擠壓、花鍵套擠壓、槽型換向器整體冷鍛、外翅片管擠壓一犁削、內外螺紋管拉拔等。 -
Apply flux to tube and socket sparingly and with a fairly thin consistency. avoid flux on areas not cleaned, particularly inside of tube
節儉地在管道和閥門插口上塗敷焊劑，使其十分均勻和細薄。要避免焊劑塗在為清理的表面上，特別是管道內側。 -
When the proper temperature is reached, alloy will flow readily into space between tube outer wall and valve socket
當溫度達到一定程度時，合金會很容易地流進管道外側與閥門承插口之間的空隙中。 -
Assembly joint by inserting tube into socket hard against the stop
將管道插入插口內，直到插不進去為止來完成連接部分的組裝。 -
Apply flame to valve at base of socket. heat uniformly, sweeping flame from fitting to tube until flux on fitting becomes quite. avoid excessive heating of valve
在閥門的承插口底部進行加熱。要均勻加熱，從連接部到管道掃著火焰，直到連接件上的焊劑不會再發出吱吱聲。要避免過度加熱閥門。 -
The strength of a brazed joint does not vary appreciably with the different brazing materials, but depends to a large extent upon the maintenance of proper clearance between the outside of the tube and the valve socket
銅焊連接的強度並不會因為採用不同的銅焊材料而又多大的變化，但是卻與管道外側和閥門插口之間的清理是否正確有很大的關系。 -
Cut tube end square to exact length needed, so that tube will enter valve socket all the way to the shoulder. ream, burr and file
根據所需長度垂直切割管道，使得管道能夠完全進入到閥門插口的肩部。刮除毛刺，進行銼磨。 -
Practice for expanded welded and silver brazed socket joints for pipe and tube
管用擴張焊接及銀黃銅套管連接件慣例 -
Standard practice for expanded welded and silver brazed socket joints for pipe and tube
管用擴張焊接及銀黃銅套管連接件 -
Clean tube to a distance slightly more than what will fit into the socket, and clean valve socket
清理管道，清理長度比插入閥門插口的長度略長一些，然後清理閥門插口。 -
Plugs, socket - outlets and couplers for industrial purposes - dimensional interchangeability requirements for pin and contact - tube accessories
工業用插頭插座輸出口和耦合器.管腳和接觸導管附件尺寸互換性要求
分享友人