uniformity of film 中文意思是什麼

uniformity of film 解釋
皮膜均一性
  • uniformity : n. 1. 一樣，一律，一式，劃一，一致。2. 均勻；無變化，單調。
  • of : OF ＝Old French 古法語。
  • film : n 1 薄層，薄膜；薄霧，輕煙；細絲狀的東西。2 【攝影】感光乳劑，照相軟片，電影膠片；影片。3 〈 pl ...
  1. Improvement of respond uniformity of pbs photoconductive film

    光導薄膜制備工藝優化
  2. There was no difference in other biologic characteristic of mscs between the two separation method, such as cell anchorage ratio and clone formation ratio. ( 2 ) plga film presented uniformity frame with no protuberance and fissure under scanning electron microscopy ( sem ). big aperture with smooth wall and average 400 m i n size running - through each other was observed in porous plga substrate, around the big aperture there were many round micropores about 5 m size. all of the structure were equal and uniform, which satisfied the further research work. ( 3 ) mscs adhesion at earlier time was promoted by biotiegenrafter 3h, cell number was ( 1. 5 0. 18 ) 105 in the plga film coated with biotiegen group, which was significantly higher than that in plga film group ( p < 0. 01 ) and higher than that in coverslip group ( p < 0. 05 ), which cell number was ( 1. 04 0. 21 ) 105. after 6h and 12h biotiegen could not promote cell adhesion, and cell proliferation and alkaline phosphatase ( alp ) activity were not promoted dramatically during 9 days. ( 4 ) cell adhesion was promoted by fibronectin or collagen type i

    G ） i型膠原、纖維粘連蛋白促進細胞增殖，細胞接種后3 、 6 、 gd三個檢測時間點，實驗組細胞均明顯高於對照組。與1型膠原相比，纖維粘連蛋白刺激作用更強。 ） i型膠原、纖維粘連蛋白尚能誘導mscs細胞向成骨細胞分化，不僅表達成骨細胞標志物ocn 、 alp 、 opnmrna ，而且堿性磷酸酶活性明顯增高，堿性磷酸酶及鈣結節7第四軍醫大學博士學位論文一染色均強陽性， i型膠原組mscs細胞堿性磷酸酶活性較fn組更高，有顯著性差異；同時，兔疫組化染色表明，經纖維粘連蛋白作用的mscs1型膠原表達陽性。
  3. The analysis results indicate that the correlative influence factors to the technological capabilities of electronic solders include the composition and purity and chemical uniformity of solder alloy, the composition and properties of mother materials and their clean level on the surface, the surface tension of liquid state solders, the temperature and atmosphere in soldering and the activity of flux, the chemical composition and structure and properties of the surface film of melting solders, and so on

    分析表明：相關的影響因素主要包括合金的組成、純度和化學均勻性；母材的成分、性質和表面的潔凈度；液態焊料的表面張力；釬焊溫度、氣氛、助焊劑的活性；液態焊料表面膜的組成、結構和性能等。
  4. Because it is easy to obtain good uniformity along thickness of film with the use of hotplate, hotplate is very commonly applied in thick film

    由於熱板易於達到在膠的厚度方向快速均勻烘乾等要求，目前越來越多地採用電熱板加熱的方式。
  5. Finite element method and matlab methods are used to simulate the film thickness uniformity. a rotating plane holder is discussed. the influencing parameters of film thickness uniformity, and the method of adjusting the parameters are studied

    在分析均勻性的過程中，引入了有限元的思想，利用有限元法ansys和matlab相結合，模擬計算了旋轉平面夾具的膜厚均勻性，分析了均勻性的影響因素，指出了工藝中的調整方法。
分享友人
分享到 Line

分享到臉書