upper blade 中文意思是什麼
upper blade
解釋
背網-
The positions of feeding and oviposition were shifted gradually from the bottom to upper of leaf sheath, and then to leaf blade with the reduction of nitrogen content in host plants
隨著稻株含氮量的下降褐飛虱取食和產卵的位置從葉鞘底部逐漸向上部轉移，直至葉片中脈。 -
The dynamo runs at rull speed to drive main shaft, then the main shaft makes the emulsifying wings in emulsification grove rotate, which absorbs the liquid in its brand groove into ring groove through guide vanes on upper and lower sides of the groove. the vanes spins circularly at high speed with the main shatf as center, and the blade and emulsificaton groove cut and crush it continuously. after that. it gers squeezed by the vanes highspeed centrifugal rotation. at last, it finishes isotropt emulsification tratment within extremely short time after continuous circulating mixing
由電動機全速運轉帶動主軸，經主軸轉動乳化框槽內之乳化翼片，使其將桶槽內之液體經框槽上、下兩側之導流葉片吸入環狀框槽內，經以主軸為中心高速圓周旋轉葉片；連續使乳化翼端刀面與乳化框間極小之間系高頻率之強力切割剪斷、粉碎，再借葉片高速離心旋轉排擠，持續循環混合，以極短之時間即可完成均質乳化之處理。 -
The surface panel method has been applied to predict the hydrodynamic performance of highly skewed propeller. the surface of propeller and its trailing vortex are discreted by a number of small hyperboloidal quadrilateral panels with constant source and doublet distribution. for highly skewed propeller, the conventional method generating grid oriented along constant radii will result in a high aspect ratio and a high skewness and a twist panel near the propeller tip on blade surface, which result easily in incorrect calculation results of velovity on blade surface, even in iteration divergence and calculation failure. a “ non - conventional grid ” is developed to acoid these problems. this grid can effectively solve the problem of the calculation and convergence for highly skewed propeller. the non - linear kutta condition of equal pressure on upper and lower at the trailing edge is executed by the iterative procedure. by sample calculating, the obtained results are satisfied the experimental data
採用面元法預報大側斜螺旋槳水動力性能，螺旋槳表面及尾渦面離散為四邊形雙曲面元，每個面元上布置等強度源匯和偶極子分佈.對于大側斜螺旋槳而言，槳葉表面採用常規的等半徑網格劃分方法在近葉梢處將導致大展弦比、大側斜和扭曲面元，這容易使槳葉表面速度的計算結果不正確，甚至會導致迭代過程發散及計算失敗.文中建立了一種「非常規網格」劃分方法，能有效地解決大側斜螺旋槳的計算和收斂問題.槳葉隨邊處通過迭代實現非線性等壓庫塔條件 -
The computer program has following advantage : the solution of main blade is by iterative scheme in time domain, the kutta condition is used by explicit equal pressure condition, the jacobian matrix which can reflect the influence on the difference between the upper and lower surface at trailing edge by dipole is calculated in each iterative procedure, in order to improve the convergence of iteration
本文編制的螺旋槳非定常性能預報程序是針對主葉在時域中迭代求解的， kutta條件採用的是顯式的等壓條件，求解中為了提高迭代的收斂性，在每次迭代中都重新計算反映偶極子強度對尾緣處上下表面壓力差影響的jacobi矩陣。 -
Here was a style where the upper blade and the lower blade were made of the same length
上刃和下刃有相同長度的，亦有上刃比下刃長的。
分享友人