valve body 中文意思是什麼
valve body
解釋
閥殼-
Design of hot extrusion mould of roughcast of multi - joint thin - wall brazen valve body
多接頭薄壁銅閥體毛坯熱擠壓模設計 -
The valve seat shall be an elastomeric seal that will permit seating at low - head pressure, and an arrow shall be molded on the valve body for permanent visibility to indicate the intended direction of flow
閥座應該是彈性密封，它使得閥座處于較低的排出壓力下，箭頭應該永久性清晰可見地模鑄在閥體上，標明計劃的流向。 -
Remove the bolts and cover, realign the diaphragm assembly, and place the cover back on the relief valve body
拆卸螺栓和閥蓋，重新校準隔膜總成，並將閥蓋放回到安全閥閥體上。 -
Lift retainer and check assembly from valve body
從閥體內取出護圈和止回閥總成。 -
Slide one half of the splash guard into the groove on the relief valve body
將防濺保護的一半滑動到安全閥閥體的溝槽上。 -
Slide the other half of the splash guard into the groove on the relief valve body and reassemble the two parts together
將防濺保護的另一半滑動到安全閥閥體的溝槽上，將兩半部件重新組裝在一起。 -
Remove handwheel and turn indicator sleeve by grasping the handwheel and pulling away from the valve body along the stem
拆卸手輪，並通過抓住手輪旋轉指示器套筒，將其沿著閥桿從閥體內拉出。 -
Straight - through type : one - way seal and eccentric structure, 90 rotation of ball on opening hidden in the valve body chamber, and straight - through flow channel without any locking and jamming
直通式：單向密封和偏心式結構，開啟時球體旋轉90 。 、球體藏在閥體球室，流道直通，不會出現卡、堵現象。 -
The failure of manufacturing cu alloy valve body by die castin g and hot extrusi on casting were point out. characteristics of squeeze casting technology were exp ounded. application of squeeze casting to cu alloy valve body in gas fired applia nce and influence of specific pressure on properties of product were analyzed
指出了壓力鑄造及熱擠壓工藝生產銅合金閥體的缺點，闡述了擠壓鑄造工藝的特徵，介紹了擠壓鑄造在燃氣器具銅合金閥體上的應用，分析了比壓對產品性能的影響。 -
The inner lining of such materials as br, nr, cr, fer, rpp, pvd, ptfe and f46 in the valve body of all kinds of cast iron and carbon steel or in the inwall of pipe castings can not only adapt to corrosion medium under different working conditions, but also can replace a great many rare and precious metal, which has, under the normal working conditions of valve, saved a large amount of funds for the users
通過在各類鑄鐵、碳鋼的閥體或管件內壁上進行內襯br / nr / cr / fer / rpp / pvd / ptfe / f46等材料，不但可以適用於不同工況下的腐蝕性介質，而且可以替代許多稀有貴重金屬，為用戶在保證閥門正常使用的條件下節約大量的資金。 -
Thedry quick isolating valve can bring about quick j oint and cut off of the valve body withno leakage of liquid
乾式快速切斷閥能夠實現閥體的快速對接和斷開，不存在流體泄漏的現象。 -
Gear operator is removed by unscrewing hex head screws which hold operator to valve body
通過擰松將操作機構固定在閥體上的六角螺栓來拆卸齒輪操作機構。 -
There may be exceptions to this if bypass piping is welded to the valve body or if a pressure relief hole is drilled in one side of the valve
但是也有例外，比如有旁通管焊接在閥體上或在閥門的一端鉆有一個減壓孔。 -
Leave the check assembly parallel to the valve body
使得止回閥總成與閥體平行。 -
To clean : inspect or replace worn valve disc, disconnect control pipe and unscrew bonnet from valve body using blunt tool and hammer on bonnet lugs
清洗：檢查或更換磨損的閥門閥瓣，斷開控制管道，用鈍工具和錘打閥蓋塞頂部，從閥體上旋下閥蓋。 -
Install valve in the direction of the flow arrows on the valve body
按照閥體上的箭頭方向安裝閥門。 -
Install valve in the line with arrow on valve body pointing in the direction of flow
在管道上安裝閥門，閥門上的箭頭方向指向水流流動方向。 -
Valve body uses comol material, lt is corrosion resistant and wear and tear resistant
閥體材質絡鉬鋼，耐腐蝕、耐磨損、經久耐用。 -
Straight moving type relief valves, mainly valve disc, valve body, spring - loaded, roof, regulation pole, conditioning nut, and other integral parts
直動型溢流閥，主要有閥芯、閥體、彈簧、上蓋、調節桿、調節螺母等零件組成。 -
Pay attention to the flow direction of medium and install the valve referring to the indicating arrow on the valve body
安裝時請認清介質流向並按閥體上指示箭頭方位正確安裝。
分享友人