vortex position 中文意思是什麼
vortex position
解釋
渦位置-
Three kinds of trapezoid, delta and airfoil shaped vortex generators are designed based on traditional, sub boundary layer and micro - vortex generators conceptual design, to study the influence of the shape, height, aspect ratio, chordwise position, spanwise position and direction angles of vortex generators on boundary layer separation control
（ 5 ）綜合分析研究了渦流發生器的工作原理和設計原則。根據國內外資料，研究了渦流發生器形狀、高度、展弦比、尖削比、弦向位置、展向位置和方位角等因素對附面層分離控制效果的影響。 -
Numerical simulation by cfd was carried out to understand the hot current behavior in a tunnel with longitudinal ventilation. it becomes clear that fire source modeling is very important because the hot current behavior is strongly affected by the fire source position and is sensitive to methods in the modeling of the fire source. the flame area which has developed from the fire source is an area of chemical reaction caused by combustion. even if grids in the vicinity of the fire source are made fine, it was difficult to simulate the heat generation area with consideration to this chemical reaction through using a method for setting the heat release rate simply on the fire source surface. therefore, we proposed a method adopting the knowledge on flame shape under the longitudinal ventilation and incorporating it into numerical simulation and it showed a good agreement with the experimental results. it was shown through experiments in a tunnel with longitudinal ventilation that the hot current developed toward the tunnel center downwind from the fire source near a wall. the cause was investigated by numerical simulation and it became clear from the results that the spiral air by the fire plume created a vortex in the crevice between the wall and the plume
運用cfd進行數字模擬，以了解縱向通風隧道內熱煙氣流的特性.通過模擬發現對火源進行模擬非常重要，熱煙氣流特性受火源位置的影響很大，並且對火源模擬方法很敏感.火源生成的火焰區是燃燒引起的化學反應區域.即使火源附近的木垛排列完好，也很難在考慮這些化學反應條件下模擬熱生成區域.建議考慮縱向通風隧道內火焰形狀並對它進行數字模擬.模擬結果與試驗結果非常吻合.試驗證明，在縱向通風隧道內，熱煙氣流從靠近墻體火源處順風向隧道中心蔓延.數字模擬結果發現，火災羽流造成的螺旋上升空氣會在墻體和羽流之間形成一個渦流區 -
Abstract : numerical simulation by cfd was carried out to understand the hot current behavior in a tunnel with longitudinal ventilation. it becomes clear that fire source modeling is very important because the hot current behavior is strongly affected by the fire source position and is sensitive to methods in the modeling of the fire source. the flame area which has developed from the fire source is an area of chemical reaction caused by combustion. even if grids in the vicinity of the fire source are made fine, it was difficult to simulate the heat generation area with consideration to this chemical reaction through using a method for setting the heat release rate simply on the fire source surface. therefore, we proposed a method adopting the knowledge on flame shape under the longitudinal ventilation and incorporating it into numerical simulation and it showed a good agreement with the experimental results. it was shown through experiments in a tunnel with longitudinal ventilation that the hot current developed toward the tunnel center downwind from the fire source near a wall. the cause was investigated by numerical simulation and it became clear from the results that the spiral air by the fire plume created a vortex in the crevice between the wall and the plume
文摘:運用cfd進行數字模擬，以了解縱向通風隧道內熱煙氣流的特性.通過模擬發現對火源進行模擬非常重要，熱煙氣流特性受火源位置的影響很大，並且對火源模擬方法很敏感.火源生成的火焰區是燃燒引起的化學反應區域.即使火源附近的木垛排列完好，也很難在考慮這些化學反應條件下模擬熱生成區域.建議考慮縱向通風隧道內火焰形狀並對它進行數字模擬.模擬結果與試驗結果非常吻合.試驗證明，在縱向通風隧道內，熱煙氣流從靠近墻體火源處順風向隧道中心蔓延.數字模擬結果發現，火災羽流造成的螺旋上升空氣會在墻體和羽流之間形成一個渦流區 -
With computations and analysis, the comprehension on the mixing and combustion process is increased, and some significative results are listed below : a ) there are three recirculation regions and one vortex region in the combustor, and these recirculation regions affect the combustion process deeply, b ) increasing side - arm angle and moving side - air inlet position toward the fuel inlet can improve mixing and combustion characteristics, and increase the combustion efficiency, c ) when the angle between two air - inlets equals to 180
通過計算與分析，增進了對補燃室內摻混燃燒過程的理解，為固體火箭沖壓發動機補燃室設計提供了一些有意義的結果： 1補燃室內的流動十分復雜，存在三個迴流區和一個旋渦區，迴流區對摻混燃燒過程有重要影響； 2增大空氣入射角度、向前移動進氣道出口位置有利於增強頭部迴流區強度，增強摻混效果，燃燒效率上升； 3 -
( 2 ) it indicates the close relationship between wet, dry phase and the position, amplitude of 500hpa high field and subtropical high. and there are close relation with polar vortex, south asia high field
（ 2 ）西北地區多、少雨與500hpa高度場和副熱帶高壓的位置和強弱密切相關，並且與極渦、南亞高壓關系密切。 -
The main conclusions show as following : 1 the effects of propagating vortex rossby waves on tc intensity change are relative closely to the position, the size and intensity of the initial disturbance
主要結果可歸納如下： 1渦旋rossby波傳播對熱帶氣旋強度變化的影響，與初始擾動相對渦旋中心的位置、初始擾動尺度大小及強度等關系密切。
分享友人