worm meshing 中文意思是什麼
worm meshing
解釋
蝸桿嚙合-
On the condition of “ many - head ” and “ small drive ratio ” ， the plane double enveloping hourglass worm can not settle the problem of undercutting and sharpening simultaneously. it has devoted to a new type hourglass worm _ sphere double enveloping hourglass worm. the coordinate system is established according to the frock. the meshing equation and the tooth equation of worm and gear have been developed and the distribution of contact line on gear tooth is analyzed. to evaluate the meshing quality ， four meshing quality indexes and five original parameters are put forward. through mass programming computing ， the relations between meshing quality and original parameters are derived and depicted by graphs
考慮到平面二次包絡環面蝸桿傳動在多頭小傳動比條件下根切與齒頂變尖的矛盾很難同時解決且嚙合性能較差，介紹了一種新型環面蝸桿傳動? ?球面二次包絡環面蝸桿傳動.在研究過程中，根據工裝建立了坐標系，根據一二包過程的運動關系推得了嚙合方程和蝸桿與蝸輪的齒面方程，分析了蝸輪齒面上的接觸線分佈.為了評價嚙合性能，提出了4項性能指標和5項原始參數，通過大量編程計算得到了嚙合性能指標與原始參數之間的關系，並以圖表直觀的表示 -
Solid model of the involute worm gearing solid model with drive ratio 1 / 50 is built by using ideas - 5. 0, then the elastic contact analysis is proceeded on the basis of contact fem. the dynamic evolution image of the area of the contact zone, the load sharing among instantaneous meshing tooth pairs, the distribution of the contact force, and tooth stress are obtained. 3
通過漸開線圓柱蝸桿、蝸輪的齒面方程式，利用ideas - 5 . 0軟體建立了傳動比為1 / 50的漸開線圓柱蝸桿傳動的實體幾何模型，在此基礎上應用接觸有限元方法對該傳動進行了彈性接觸分析，包括接觸區的形狀、位置、載荷在瞬時嚙合齒對的分配狀況； 3 -
Creative points and all tasks having be finished are briefly shown below : according to the classical space meshing theory, we have strictly deduced a series of formulae such as the equation of contacting line of worm, the equation of the second limiting curve of worm gear, and the equation of working surface and non - working surface, etc. and we have deeply studied the algorism of the actual contacting lines of worm gear drive
本文的主要創新點和成果如下：基於經典共軛嚙合理論，對平面二包蝸桿副的運動關系進行了嚴密分析，獲得了蝸桿副齒面方程、蝸桿齒面一界曲線方程、蝸輪齒面二界曲線方程等一系列齒面分析所必須的數學公式，並深入研究了蝸桿副齒面接觸線的演算法，為蝸桿副的三維數字化造型打下了堅實的數學基礎。 -
Tooth surface equations and contact line equations of the involute worm gearing are established according to its machining methodology. meshing characteristics in rigidity condition are studied. these characters include the inductive normal curvature along the contact line on the worm surface, the first and the second limit lines during the engage of the worm gear, and the influence of the intersect angle between the contact line the relative velocity of the worm and the gear on transmission performance
根據漸開線圓柱蝸桿傳動的創成方法，建立了漸開線圓柱蝸桿和蝸輪的接觸線方程式、齒面方程式，分析了漸開線圓柱蝸桿傳動的剛性嚙合特性，如蝸桿與蝸輪嚙合時的誘導法曲率、一類界限曲線、二類界限曲線和蝸桿與蝸輪間相對速度方向和接觸線方向的夾角對傳動性能的影響； 2 -
The meshing efficiency of the drive is studied and analyzed in theory. the different formulas for meshing efficiency of drive are introduced on different conditions when stator or worm is fixed respectively
從理論上研究分析了滾錐齒超環面行星蝸桿傳動的嚙合效率，推出了在定子固定和蝸桿固定兩種情況下滾錐齒超環面行星蝸桿傳動嚙合效率的計算公式。 -
The process has an advanced principle. the involute hourglass worm drive can realize the design machining of gear form and direction, and the internal meshing honing gear has high efficiency. this process has all merits mentioned above, and also has the advantages of quality stability, high productivity for rude and finish machining
該工藝原理先進，它集有利於實現齒形、齒向設計加工的漸開面環面蝸桿傳動與高效的內嚙合珩齒的優點與一體，對齒輪的粗、精加工都有質量穩定、生產效率高的優點。 -
The paper researches a new type mechanical transmission mechanism - the rolling cone - type toroidal drive. the meshing efficiency has been studied completely and systematically and the parameters of drive are optimized on the base of analysis about meshing. by taking advantage of computer technology the main parts of the drive - stator, planet gear and worm are modeled and emulated
在對其進行嚙合分析的基礎上，對該傳動的嚙合效率進行了深入研究，並對該傳動進行了參數優化，進而利用計算機技術，對該傳動的主要零件? ?行星輪、環面定子和環面蝸桿進行了三維建模模擬，演示了該傳動的運動情況。 -
Abstract : the paper suggests two methods for adjusting the mesh clearance in cylindrical worm drive : one is to adjust the meshing center distance of worm gears, the other is to use dual lead cylindrical worm, introducing briefly the principle of adjustment and making a comparison between the characteristics of the two methods
文摘:提出了兩種調整圓柱蝸桿傳動嚙合側隙的方法:通過改變蝸輪蝸桿的嚙合中心距來改變其嚙合側隙;採用雙導程蝸桿傳動以調整蝸輪蝸桿的嚙合側隙，簡述了調整原理，並比較了兩種調整方法各自的特點。
分享友人