側刀片 的英文怎麼說

中文拼音 [zhāidāopiān]
側刀片 英文
side blade
  • 側 : 側形容詞[方言] （傾斜; 不正） slant; sloping
  • 刀 : Ⅰ名詞1 （切、割、削、砍、鍘的工具） knife; sword 2 （形狀像刀的東西） sth shaped like a knife 3 ...
  • 片 : 片構詞成分。
  • 刀片 : 1 （刮鬍刀片） razor blade2 [機械工程] （片狀零件） （tool） bit; blade; cutter blade; fly bar刀...
  1. When the equipment is wirking, the blades will be nipped on the table. after the blades is faced with table side face, the workstations can be transferred to any angle. milled into an any angle blade, automatic lubrication, automatic cooling, especially for the aerodynamic drawknife blades

    本機在工作時，將刀片夾在工作臺上，刀刃與工作臺的側面面對齊壓緊后，可以將工作臺轉至任何角度，磨成任意角度的刀刃，自動潤滑，自動冷卻，適應于不同厚度，不同規格的刀片，成其適合於氣動刮刀刀片面性的研磨。
  2. The dynamo runs at rull speed to drive main shaft, then the main shaft makes the emulsifying wings in emulsification grove rotate, which absorbs the liquid in its brand groove into ring groove through guide vanes on upper and lower sides of the groove. the vanes spins circularly at high speed with the main shatf as center, and the blade and emulsificaton groove cut and crush it continuously. after that. it gers squeezed by the vanes highspeed centrifugal rotation. at last, it finishes isotropt emulsification tratment within extremely short time after continuous circulating mixing

    由電動機全速運轉帶動主軸，經主軸轉動乳化框槽內之乳化翼片，使其將桶槽內之液體經框槽上、下兩側之導流葉片吸入環狀框槽內，經以主軸為中心高速圓周旋轉葉片；連續使乳化翼端刀面與乳化框間極小之間系高頻率之強力切割剪斷、粉碎，再借葉片高速離心旋轉排擠，持續循環混合，以極短之時間即可完成均質乳化之處理。
  3. Now i seem to have hit a sweet spot ( slightly left of center ) where the bhs are hitting with the fps on a left / right plane at 20 and 30yds

    現在么，我』 』似乎』 』發現了這個很妙的搭箭點（平衡中心略微偏左） ，從這個位置發射的刀片箭頭，在20和30碼的距離，還能水平分佈在子彈箭頭的左右兩側，可是
  4. Clean, bone and fillet the fish, score and cut into squares, season with cooking wine, msg, salt, and scallion and ginger sauce. saute the fish in 6 - fold hot oil until the squares curl up, drop in the scallops, thicken slightly

    魚治凈，片下兩側魚肉，去大骨刺，剞花刀后切成方片，用料酒味精鹽蔥薑汁入味，下6成熟熱油中滑成魚球至熟，下鮮貝勾薄芡裝盤即成。
  5. Based on the principle of inclined offset surface, the calculation and generation of nc cutter location for small divided area of blade were introduced. in addition the computer simulation and the path chart of cutter center were given to prove the tool path

    在每一段曲面上，基於斜等距曲面的原理，推導出葉片分段側銑加工時刀位軌跡的生成和計算；並用計算機模擬和刀心軌跡圖對刀位進行了驗證。
  6. Precision ground blade on both sides for tighter packing chamber sealing. sealing face of the gate is lapped to provide the best possible seat tightness

    兩側都經過精密光亮磨光的刀片確保填料腔的氣密性密封。閘板的密封面經過研磨，以提供最好的閥座密封性。
  7. Side milling cutters with exchangeable blades ; carbide - tipped

    帶可換刀片的側銑刀.硬質合金刀片
  8. Side milling cutters ; carbide - tipped

    鑲硬質合金刀片側銑刀
  9. Internal side turning tools for corner work with carbide tips

    硬質合金刀片角加工用內側車刀
  10. Put the blade in the inner side of the transparent vessel

    將刀片置於透明容器的內側。
分享友人
分享到 Line

分享到臉書