共軛壓力 的英文怎麼說
中文拼音 [gòngèyālì]
共軛壓力
英文
conjugate pressure-
The fault controlled the magmatism and metallization relevant to the contact zone, and deformed successively and produced cataclastic rocks and two sets of joints ; the second stage was from late cretaceous to eocene. the fault zone deformed right - laterally under ne - sw striking transtention, and new joints zone was produced at the end of the two main faults because of local stress concentration. the fault produced inchoative cataclastic rocks, and two sets of typical joints in plutons ; the third stage of deformation was relatively faint and only a little of microcracks was produced and infilled with vei ns in the deformed rocks, which was during the himalayan movement
其後的繼承性活動在斷裂帶內形成碎裂程度最強達到碎裂巖的碎裂巖系列構造巖，變形帶兩側發育兩組典型的共軛剪節理；第二次在晚白堊世?始新世，斷裂在北東?南西向近水平擠壓作用下右行張扭性活動，斷裂帶兩主斷裂在斜列重疊的端部由於局部應力集中進一步擴展形成節理帶，而斷裂在巖體區也發育兩組典型的共軛剪節理，斷裂內形成初碎裂巖為主的構造巖；第三次是喜山期以西側抬升、東側下降的強烈升降為主的活動，在基巖中，主斷層兩側圍巖出現微破裂。According to the linear superposition principle of quantum mechanics in this thesis, it is constructed the kind ( ii ) of multi - mode superposition state of differ - intensity of nonsymmetry state superposition state with distinguishable two quantum states light field composed of the linear superposition of multi - mode complex conjugation coherent state of contrary state and multi - mode imaginary conjugation coherent state of contrary state. by utilizing the theory of multi - mode squeezed states
本文根據量子力學中的線性疊加原理，構造了由多模（ q模）復共軛相干態的相反態和多模虛共軛相干態的相反態這兩者的線性疊加所組成的第種強度不等的非對稱兩態疊加多模疊加態光場，利用多模壓縮態理論，對態。From the aspect of geometry, structure design, manufacture and examine, this paper generally summarizes the gcm ' s study progress in detail, discusses its kinetic rule and the determination of its primary structure parameter, and educes its surface equation and pressure angle equation based on the homogeneous matrix transformation and the conjugate engagement theory of spatial surface. on the basis of geometry study of gcm, the paper makes a comprehensive analysis to the interference phenomenon that will possible exist in the assemble course of two different structure of gcm with the help of matlab software
本文從運動幾何學、結構設計、動力學、製造和檢測等方面對國內外弧面凸輪機構的研究進展進行了全面綜述，詳細論述了高速凸輪機構的運動規律和弧面凸輪機構基本尺寸的確定，基於空間曲面共軛嚙合原理，通過齊次變換推導了外弧面凸輪的曲面方程和壓力角方程，並提出了對應的廓面修形演算法；提出了內弧面凸輪機構的構想，推導了內弧面凸輪的曲面方程和壓力角方程。Principal compresso stress of mineralization epoch is measured 34 - 46ma by means of ae method, and its orientation is ew - trending by conjugate fracture, at last, the dynamic mechanics of the rhombic shear fault grid is analysised, ore - controlling law of the regional and ore - belt are determined, and combined with geophysical prospecting, ore - forming are forec ast
利用巖石聲發射測得成礦期主壓應力值為34 - 46mpa ，以共軛破裂求得主壓應力方位為近ew向，分析了本區菱形剪切斷裂網格控礦構造應力場的動力學機制。提出區域和礦帶的成礦控礦規律，結合物探進行了成礦預測。Taking the meshing theory of conjugate curved surface as a foundation, utilizing array method of rotation transformation of vector, the meshing equation and contour surface equation of conical cam mechanism with swinging conical roller follower were analyzed and derived, and the calculation formula of pressure angle and synthetic curvature of the mechanism was presented, thus laid a solid theoretical foundation for enhancing the machining accuracy of conical cam, improving its processing method and achieved the integration of cam cad / cam
摘要以共軛曲面嚙合理論為基礎，運用矢量的旋轉變換矩陣法，分析並推導了圓錐滾子擺動從動件圓錐凸輪機構的嚙合方程和廓面方程，並給出了機構的壓力角和綜合曲率的計算公式，為圓錐凸輪加工精度的提高，改進其加工方法，實現凸輪cad / cam一體化奠定了堅實的理論基礎。分享友人