轉矩式功率計 的英文怎麼說

中文拼音 [zhuǎnjǔshìgōnglǜjì]
轉矩式功率計 英文
torque-type power meter
  • 轉 : 轉構詞成分。
  • 矩 : 名詞1. （畫直角或正方形、矩形用的曲尺） carpenter's square; square2. （法度; 規則） rules; regulations 3. [物理學] moment
  • 式 : 名詞1 （樣式） type; style 2 （格式） pattern; form 3 （儀式; 典禮） ceremony; ritual 4 （自然科...
  • 功 : 名詞1 （功勞） exploit; merit; meritorious service [deed]: 戰功 military exploits; 立功 render me...
  • 率 : 率名詞（比值） rate; ratio; proportion
  • 計 : Ⅰ動詞1 （計算） count; compute; calculate; number 2 （設想; 打算） plan; plot Ⅱ名詞1 （測量或計算...
  1. Based on the basic analysis of the structure and power elements of the hybrid vehicle, this thesis presents a powertrain system with a metal pushing belt cvt, aiming to the development status and trend of the hybrid vehicle technology in our country. a rational control strategy and its work mode of this powertrain system are determined, and correlative parameters such as the engine power, the starting torque, and the differential ratio, the rated power and torque of the motor, and the ratio of the torque synthesizer are systematically designed for the changan star 6350b. at the same time, the design of these parameters is considered as the base of the simulation of the motor control system in next step

    在對混合動力汽車的結構型式和動力元件進行基礎性理論分析后，針對我國汽車技術發展現狀和混合動力汽車技術的發展趨勢，設計了一種基於金屬帶式無級自動變速器cvt混合動力汽車動力傳動系統方案，根據該傳動系統方案制定了比較合理的控制策略和工作模式，並針對長安之星6350b設計了發動機功率和起始轉矩、主減速比、電機的額定功率和轉矩、轉矩合成器速比等相關參數，為下一步的電機控制系統模擬實驗打下基礎。
  2. Xh, xb series high power gear units is a brand - new model of rigid tooth flank gear reducers with wide application areas, which has the feature of large torque range, a design of unit structure modulization capable of horizontal mounting and vertical mounting, three kinds of output shafts - solid shaft, hollow shaft and hollow shaft with shrink disk

    Xh xb斜傘系列大功率減速機xh xb斜傘系列大功率減速機是全新型硬面減速機，具有大轉矩范圍，採用單元結構模塊化設計可臥式安裝也可立式安裝。有實心軸空心軸和收縮盤空心軸輸出。
  3. The basic working principles and characteristics of srm will be described firstly in this paper, as well as its developing survey and researching directions. and then the srd system will be separated into several function parts to be introduced respectively in details : ( 1 ) to analyze the basic characteristics of the srm including electromagnetism, current and torque of every angle field of the rotor based on the subsection - linearized inductance characteristics of stator windings and several idealized supposes. ( 2 ) how to design and realize the h - bridge converter, and the method to use it ; ( 3 ) how to design and realize the controller based on dsp ( tms320f240 ) and the control strategies, as well as the program ; ( 4 ) to introduce the monitor program running in a pc, which is programmed by delphi

    本文首先介紹了srm的基本工作原理和特點以及srd系統發展概況和研究方向，然後以srd的功能構成為線索分部分進行介紹： （ 1 ） srm的特性及控制策略分析，在電感分段線性化等簡化條件下分析得出了各個轉子位置角度區間的電磁、電流和轉矩特性並分析了控制策略； （ 2 ）分析設計了h橋式功率變換器的設計和工程實現的方法，並設計了基於這種功率變換器的換相邏輯； （ 3 ）分析設計了以dsp為核心的控制器以及控制方法，並介紹了該控制器的軟硬體實現； （ 4 ）介紹了如何用delphi編制實現上位機監控程序。
  4. The official power figure reads a metric 280ps at 6, 500rpm, which is equivalent to 276hp ( 206kw ). max torque stands at 422nm ( 311ft - lb ), coming in at 3, 500rpm

    官方正式公布的動力數據為280公制馬力@ 6500轉，相當於276英制馬力（ 206千瓦） 。不過我們預計最終量產版的功率要大於官方公布的數據。峰值扭矩將有望達到422牛米@ 3500轉。
  5. This product acquires engine crank corresponding phase signal and rotating speed signal, which after ecu treatment, are used together with signals collected from other load sensor ( such as shutter location sensor ) to achieve electronic control over engine ignition timing. compared with mechanical ignition timing control, this is more precise and reliable, resulting in optimized performance of engine in oil consumption, exhaust, output and torque

    Fdw465b型電噴分電器總成採集發動機曲軸相位信號及轉速信號，同其它負荷傳感器（如節氣門傳感器等）採集到的信號，經電控單元ecu計算處理后，實現對發動機點火正時的電子控制，較之機械式點火正時控制更加精確、可靠，使汽車發動機系統的綜合性能得到較大提高，特別是發動機的燃油消耗率、排放、輸出功率、扭矩等方面都得到較大優化。
  6. Mostly conventional boxed hardware instrument is used, by which the signal from sensors is processed by circuit board, and inputted to secondary instrument that is box hardware instrument, and displayed by numerical tube

    轉矩功率測量大都採用傳統的箱式硬體儀表，用電子電路卡來處理從傳感器出來的信號，然後再進入二次儀表，即箱式硬體儀表，並用數碼管將計算值顯示出來。
分享友人
分享到 Line

分享到臉書