割圓曲線 的英文怎麼說
中文拼音 [gēyuánqūxiàn]
割圓曲線
英文
quadratrix-
Round these two respects, how to structure security elliptic curve cryptography and the implementations of ecc is first discussed in this paper. then we have analysed especially the scalar multiplication on the elliptic curves, and present a new algorithm to quickly implement the fixed point scalar multiplication according to the idea of interleaving exponentiation algorithm and power division. this algorithm is much faster than fixed - base windowing method ; and a little faster than fixed - base comb method
圍繞這兩個方面的問題，本文首先討論了如何構造安全的橢圓曲線密碼體制和橢圓曲線密碼體制的應用；然後重點分析了橢圓曲線上數乘運算的快速實現，並結合interleavingexponentiation演算法和冪分割的思想，提出一種計算固定點數乘的快速演算法，該演算法的計算速度明顯快于fixed - basewindowing演算法，稍快于fixed - basecomb演算法。Among such curves are the quadratrix invented by hippias.
在這樣的曲線中有希皮阿斯發明的割圓曲線。The function of the software use pc - computer to dispose the output signal which is produced by the device as following steps : ( 1 ) to input data by parallel interface ( 2 ) to record and form a file ( 3 ) to demonstrate results step by step ( 4 ) the results could be compiled ( 5 ) it can synthesis in the permitted error scope, substituted original dot for line or arc, finally we could get a graph that is described by some simply curve. ( 6 ) to convert these graph into a program, which used in the cutting process of numerical control. ( 7 ) the software also includes some protective methods
而系統處理軟體的作用是：利用pc兼容機，將上述裝置的輸出信號（ 1 ）通過并行口輸入（ 2 ）記錄成文件（ 3 ）逐點顯示出來（ 4 ）可人工進行化簡，編輯（刪、改點）等（ 5 ）可在給定誤差范圍內進行人工擬合，用直線和圓弧取代原來的點，得到一個與原圖形的誤差在規定范圍內，又消除跟蹤過程中因受到各種干擾而造成的缺陷，由盡可能少而簡捷的數學曲線描述的圖形（ 6 ）把這些圖形轉化成用於編制數控線切割加工程序及autocad能夠識別的文件（主要指dxf格式） （ 7 ）該軟體還有一定的加密措施。A control method is presented where least square arc approximation and timed interpolation are employed. using it, the number of segments of fitted curves is made minimum while the accuracy is guaranteed, so that data transmission between cad and cnc systems is decreased and setted feeding rate can be realized. this method has already success fully been used for flame cutting and controlling saddle - backed curve for pipe connection when feeding rate is required to be higher
提出了一種採用最小二乘法圓弧逼近及定時插補控制方法，在保證精度的前提下，可使擬合圓弧段數最少，從而減少cad系統與cnc系統的數據傳送，可實現給定進給速度.該方法已成功地應用於要求較高進給速度的接管馬鞍型曲線火焰切割擬合控制Taking practical situation of this project and much engineering experience into account, the scheme with axle golden section elliptical arc surface is proposed through comparing nine optimization schemes with model test
結合工程實際和以往經驗，比較了9種進水口曲線型式的試驗結果，確定了長短軸黃金分割比的橢圓弧面的方案。The surface of conventional engineering part is composed of simple analytical surfaces and four - boundary ruled surface primarily. therefore a point cloud segmentation method based on those feature surfaces is proposed. several algorithms to identify the simple analytical surface feature are investigated and discussed
常規工程零件的外表面中包含了大量的特徵曲面，如簡單解析曲面和四邊直紋面，因此，本文提出基於特徵曲面的的點雲分割方法，研究幾種識別簡單解析曲面的演算法；研究由點雲擬合b spline和b zier曲線的理論基礎，總結曲面擬合的幾種方法，提出一種反求定半徑滾球圓角的方法。分享友人