動作構件 的英文怎麼說
中文拼音 [dòngzuògòujiàn]
動作構件
英文
actuating member-
In this paper, ackerman steering linkage of double - wishbone suspension is taken as the study object, choosing the splitting joint and steering lever joint to carry out the design of optimization the mathematics models are established based on the multi - body system dynamics, applying its analysis method of kinematics to study the mechanism kinetic principles owing to more spatial factors considered, and calling off many hypotheses affecting the accuracy, compared with the traditional methods, the models are better to reflect the realistic motion principles, the results are more exact and applicable moreover, the force analysis is applied to the conduct mechanism the analysis method of dynamics in the multi - body dynamics is applied to study the forces applied on every component, working out the constraint reaction force of up and down ball joints, and developing the current computation program in the end, produce the upper wishbone geometry model in the ansys software package, meshing and carrying out the fea, testifying if the intensity of the wishbone meet with the requirements
本文以雙橫臂獨立懸架的轉向傳動機構作為研究對象，選擇對斷開點和節臂球銷的位置進行優化設計，在此基礎上建立了基於多體系統動力學的導向機構和轉向傳動機構的數學模型，運用該學科的運動學分析方法研究機構的運動規律，編制了通用優化設計軟體。由於考慮了更多的空間因素，取消許多影響準確性的假設，因此建立的數學模型與傳統的方法相比更能反映實際運動規律，得到的優化結果也更加精確實用。此外，本文還針對導向機構進行受力分析，在建立該機構的空間動力學模型后，運用多體動力學中的動力學分析方法研究各個桿件的受力，計算出上下球鉸的約束反力，並開發出了相應的通用計算程序。Jzc series concrete mixer is gravity type twin - prick reversed discharging mixer. stirring roller is driven by geared ring, and it will stir deasil and discharge reversely, and can stir plastic, damp dry and hard concrete, fit for common building site, road, bridge project and different concrete component factory
Jzc系列混凝土攪拌機系自落式雙錐反轉出料攪拌機，攪拌筒由圈傳動，工作時正轉攪拌，反轉出料，可攪拌塑性和半干硬性混凝土，適用於一般建築工地道路橋梁工程及各種混凝土構件廠。The primary function of the software are confirming the fundamental dimensions of the ditcher, optimizing the volume of reducer, carrying through dynamic, real - time simulation to working part
該軟體的主要功能為：確定新型蓄水保墑機具機構基本尺寸；對減速箱的體積進行優化；對工作部件的運動進行實時的、動態的模擬。Event condition action rule based intelligent agent architecture
基於事件條件動作規則的智能主體結構11 katoen j - p, langerak r, latella d, brinksma e. on specifying real - time systems in a causality - based setting. lecture notes in computer science 1135, 1996, pp. 385 - 405. 12 fecher h, majster - cederbaum m, wu j. refinement of actions in a real - time process algebra with a true concurrency model
在系統模型的結構表示上，本文擴充了傳統的事件結構，使用一種帶時間信息的捆綁式事件結構來模擬系統行為，在系統模型的語言刻畫上，本文採用的是帶時間的類lotos進程代數描述語言，對于動作精化，我們同樣採用運算元的觀點，將動作精化定義為一個操作運算元。It is necessary to control the mechanical stimuli precisely in the studies of cardiac mechano - electrical feedback ( mef ). in the present study a ventricular pressure - clamping system has been developed, which can be applied to isolated - perfused rabbit hearts. controlled by a computer, this system not only can make the left ventricle follow a command defining the same pressure wave as that during a beating cycle under physiological condition, but also deliver mechanical stimuli with a proper waveform to the ventricle at a particular time phase. this system integrates multiple functions, including perfusing, pacing, recording of electrocardiogram and monophasic action potentials, and clamping and measuring of ventricular pressures in isolated - perfused hearts. thus, it is a distinct system for investigating the phenomena and mechanisms of cardiac mef at organ level
在心臟機械電反饋的研究中準確控制機械刺激是非常重要的.本研究室構建了一套適用於離體家兔心臟的心室壓力鉗系統.該系統通過計算機控制壓力鉗，不僅能模擬正常生理條件下左心室的壓力波形，還能在心室活動周期的特定時相、以適當波形對心室施加機械刺激.該系統集心臟灌流與起搏、表面心電圖記錄、單相動作電位記錄、心室壓力鉗制與測定等多種功能於一體，特別適用於器官水平上觀察機械電反饋現象並探討其機制Abstract : it is necessary to control the mechanical stimuli precisely in the studies of cardiac mechano - electrical feedback ( mef ). in the present study a ventricular pressure - clamping system has been developed, which can be applied to isolated - perfused rabbit hearts. controlled by a computer, this system not only can make the left ventricle follow a command defining the same pressure wave as that during a beating cycle under physiological condition, but also deliver mechanical stimuli with a proper waveform to the ventricle at a particular time phase. this system integrates multiple functions, including perfusing, pacing, recording of electrocardiogram and monophasic action potentials, and clamping and measuring of ventricular pressures in isolated - perfused hearts. thus, it is a distinct system for investigating the phenomena and mechanisms of cardiac mef at organ level
文摘:在心臟機械電反饋的研究中準確控制機械刺激是非常重要的.本研究室構建了一套適用於離體家兔心臟的心室壓力鉗系統.該系統通過計算機控制壓力鉗，不僅能模擬正常生理條件下左心室的壓力波形，還能在心室活動周期的特定時相、以適當波形對心室施加機械刺激.該系統集心臟灌流與起搏、表面心電圖記錄、單相動作電位記錄、心室壓力鉗制與測定等多種功能於一體，特別適用於器官水平上觀察機械電反饋現象並探討其機制This text divides into five chapters altogether : chapter one in the introduction, have introduced the common sensor of displacement, has pointed out the fine characteristic of hall ' s sensor, put forward the basic task ; chapter two have introduced the basic operation principle of hall ' s component ; chapter three introduce hall temperature performance, electromagnetic characteristic, zero error, frequency characteristic and these parameter commonly used compensation method and hall simple application of component ; chapter four having recommended the measurement principle of the feedback servo mechanism, systematic implementation method, the experimental result has appeared, structure the mathematics model, and has analysed the error ; chapter five have pointed out the developing direction in the future while looking forward to
本文共分為五章：第一章緒論中，介紹了常見的位移傳感器，指出了霍爾傳感器的優良特性，提出了基本任務；第二章介紹了霍爾元件的基本工作原理；第三章介紹了霍爾元件的溫度性能、電磁特性、零位誤差、頻率特性以及這些參數常用的補償方法和霍爾元件的簡單應用；第四章介紹了反饋隨動機構的測量原理，系統的實現方法，給出了實驗結果，構建了數學模型，並對誤差進行了分析；第五章展望中指出了今後的發展方向。If can utilize hall ' s component to measure displacement under the condition of the simple magnetic field, increase the range of measuring ; it inertia little, merit that exposed to make it function in the measurement of vibration and in various kinds of displacement, become a kind of displacement sensor with fine performance. it can solve this difficulty to adopt the feedback servo mechanism
若能在簡單磁場的條件下利用霍爾元件測量位移，增加測量范圍；它慣性小、非接觸的優點將使它在各種位移與振動的測量中發揮作用，成為一種性能優良的位移傳感器。採用反饋隨動機構可解決這個困難。Optimal design with three variables is then done to the elbow - bar mechanism of the mp1040b moulding machine by utilizing the method of punishing function for constraint problems and variational scale for unconstraint problems. the optimal target function is the maxium of gradient in one work travel for the moulding plank of the elbow - bar mechanism. the result shows that the maximal gradient of moulding plank in one motion period declines by 25. 7 after optimization, and the angular acceleration of the bottom moulding plank decreases greatly
動力學分析中，各構件的質量和轉動慣量是通過pro / engineer軟體，先建立各個構件幾何模型而求得；然後，利用解決約束問題的罰函數法和處理無約束問題的變尺度法對mp1040b型模切機肘桿機構進行三個設計變量的優化設計，優化目標函數為肘桿機構的下模切板在一個工作行程中達到的最大傾斜程度；通過優化設計，模切機肘桿機構的下模切板在一個工作行程中的最大傾斜程度降低了25 . 7 ，其角加速度明顯減小，提高了模切機動力學性能。In this paper, three unique models were designed to research atom diffusion at interface, contacting line and joining point under bpec heating and compare with it under radiation heating in order to find out if bpec speed atom diffusion. the first model was aimed to research atom diffusion at interface under bpec heating. experiment condition of bpec diffusion welding sheet cu and ni : direct diffusion welding, at a pressure of l0mpa, welded at 750 ~ 900, with heat rate of 200 ~ 400 / min for 10mm, on / off of 6 / l ~ 48 / 8, with die or not, vacuum of 6pa
本文設計出三種樣品預構件，研究脈沖大電流加熱條件下片狀材料、線狀材料和球形顆粒之間的原子擴散過程，弄清脈沖大電流加熱條件下原子擴散與一般燒結和焊接過程中原子擴散的區別，以證實特殊的電場和磁場是否對原子的擴散有推動作用，揭示脈沖大電流加熱條件下原子的擴散過程，探索脈沖大電流熱加工技術快速高效的原因。To meet the demands for large space and flexible compartmentation of buildings, laminated vierendeel trusses are adopted in high - position transfer story structures. first the bearing characteristics are analyzed, in which reasonable stiffness ratio of the upper chord, middle chord, and lower chord is derived. then combined with an actual engineering model ( 1 8 similar ratio ), the static loading and pseudo - dynamic tests of two models for laminated vierendeel truss used in transfer story structures are conducted, in which one model adopts reinforced concrete, and the other adopts prestressed concrete and shape steel concrete. seismic behaviors are analyzed, including inter - story displacement, base shear - displacement skeleton curves, and equivalent viscosity - damping curves. a program is programmed to carry out the elasto - plastic dynamic analysis, and displacement time - history curves of the two models are derived. the test and analysis results show that the laminated vierendeel truss with prestressed concrete and shape steel concrete has excellent seismic behaviors. it can solve the disadvantages of laminated vierendeel trusses used in transfer story structures. finally, some design suggestions are put forward, which can be referenced by similar engineering
為滿足建築物大空間和靈活隔斷要求，在高位轉換層結構中採用迭層空腹桁架結構.首先分析了其受力性能，得出了空腹桁架各構件合理的截面剛度以及布局形式.然後結合一實際工程，進行了兩榀迭層空腹桁架轉換結構模型（ 1 : 8相似比）的豎向荷載下靜力試驗以及擬動力試驗.其中一榀為普通混凝土迭層空腹桁架，另一榀配置了預應力和鋼骨混凝土，對比分析了兩模型的層間位移比、骨架曲線以及等效粘質阻力系數等抗震性能的比較，並進行了彈塑性動力分析.試驗和分析結果表明，配置預應力和型鋼混凝土的迭層空腹桁架轉換結構具有良好的抗震性能，可以成功地解決迭層空腹桁架作為轉換層結構所產生的弊端問題，最後對這類轉換層結構提出了相應的設計建議Based on the basic analysis of the structure and power elements of the hybrid vehicle, this thesis presents a powertrain system with a metal pushing belt cvt, aiming to the development status and trend of the hybrid vehicle technology in our country. a rational control strategy and its work mode of this powertrain system are determined, and correlative parameters such as the engine power, the starting torque, and the differential ratio, the rated power and torque of the motor, and the ratio of the torque synthesizer are systematically designed for the changan star 6350b. at the same time, the design of these parameters is considered as the base of the simulation of the motor control system in next step
在對混合動力汽車的結構型式和動力元件進行基礎性理論分析后，針對我國汽車技術發展現狀和混合動力汽車技術的發展趨勢，設計了一種基於金屬帶式無級自動變速器cvt混合動力汽車動力傳動系統方案，根據該傳動系統方案制定了比較合理的控制策略和工作模式，並針對長安之星6350b設計了發動機功率和起始轉矩、主減速比、電機的額定功率和轉矩、轉矩合成器速比等相關參數，為下一步的電機控制系統模擬實驗打下基礎。The vibration of upper structure of bridge which caused by the dynamic action of vehicle pass the railway bridge may make the structural component fatigue and decrease the intensity and stability. the more vibration of bridge will influence the safety and stability of vehicles ; when the dynamic changing frequency of vehicle equal or approach to the free vibrational frequency of bridge, wh ich will make the resonance may intensify the response of bridge and vehicles
列車動力作用引起橋樑上部結構的振動可能使結構構件產生疲勞，降低其強度和穩定性；橋梁振動過大可能會對橋上車輛的運行安全和穩定性產生影響；當列車的動力變化頻率與橋跨結構自振頻率相等或接近時，引起的共振可能會使車橋動力響應加劇。Design and construction tools can automate moving from high - level constructs to working code by providing wizards to automate design, construction, and test tasks by generating code and enabling usage of code snippets, and by converting integration and testing into seamless development tasks through integrated development, build, and test environments
設計和構建工具可以通過提供自動化設計，構建，和測試任務的向導來自動化從高級構件到工作代碼的轉移，而向導的自動化功能是通過產生代碼和允許代碼片段的使用，以及把集成和測試通過集成化開發，構建，和測試環境轉變為無縫開發任務實現的。Aimed at design index of input power 1. 5kw, most output rotate velocity 300rpm, and rating output rotate velocity 150rpm, considering factors of angle and ratio of transmission, on the basis of kinematics simulation, author optimized the kinematics parameters. in this paper, author has made some analysis and study to the primal assembly condition of transformer ' s sequential action in theory, designed structure dimension of the input and output transformer, and verified the corresponding strengthen. further, the structure, which is to key transmission components of velocity control system of the speed regulator, has been designed based on meeting operational sensitivity, precision and self - locking
本文針對輸入功率為1 . 5kw ，最大輸出轉速，額定輸出轉速的無級變速器的設計要求，並考慮到傳動角及變速比等因素，在運動學模擬的基礎上，對運動學參數進行了優化；本文對變換器連續作用的初始裝配條件進行了理論分析與研究，對輸入、輸出變換器作了結構尺寸的設計，並進行了強度校核計算；本文還對變速器調速系統中主要傳動構件在滿足操作的靈敏度、精度、自鎖性的基礎上進行了結構設計；最後採用workingmodel3d軟體，進行虛擬樣機的計算機輔助模擬設計及運動學和動力學計算。A trademark used for a typesetting machine operated from a keyboard that activates a unit that casts and sets individual characters
莫諾鑄排機一種排字機的商標，通過使一個構件動作的鍵盤來操作，這種構件可以澆鑄或排版單個字Firstly, this part analyzes location, natural conditions and natural resources, population and labors, socio - economic elements, and the impacts of global political and economic environment change on unbalanced development of japanese regional economy. secondly, through analysis on regional development before the meiji reformation, industrialization, formation of dual structure and regional development after war, this part puts forward that unbalanced development is an objective law and regional development policies of government ca n ' t change structure of unbalanced development essentially. finally, this part sums up motive mechanism of unbalanced development of japanese regional economy, including location directional feature, scale economy, congregation and diffusion economy, putting forward that the overall effects of the three types of mechanisms stated above can be summarized as industrial group effects, which is also the important mechanism of unbalanced development of japanese regional economy
首先，分析了區位條件、自然條件與自然資源、人口與勞動力條件、社會經濟條件、國際政治經濟環境的變化對日本區域經濟非均衡發展的影響；其次，通過對日本明治維新前的地域開發、工業化及其二元結構的形成以及戰后的地區開發等過程進行了剖析，認為區域經濟非均衡發展是一個客觀規律，政府的地區開發政策並不能從根本上改變非均衡發展的格局；第三，總結了日本區域經濟非均衡發展的動力機制，主要包括區位指向性、規模經濟、集聚與擴散效應，指出上述三種機制的綜合作用可以概括為產業集群效應，即產業集群也是日本區域經濟非均衡發展的重要機制。Usually, electrostatic motors are employed as micro - mechanical dynamical components in microactuators. electrostatic motors take charge in changing electrical signal into mechanical movement. as a result, the bulk and function of them will make direct influence on the whole performance of mems
在微型執行器中，通常採用靜電電動機作為微機械動力構件，它負責將電信號轉換成機械運動，其體積大小和性能優劣直接影響到mems的整體品質。The whole building can be equivalent to a cantilever bar, and the structural total displacements can be divided into parallel displacement and rotational displacement based on the harmonize condition of displacement, and the parallel shear and the rotational shear of the elements can be accordingly obtained by selecting the renegade body from top to bottom in turn
根據位移協調條件，將結構的位移分解成平動與轉動成分，得到相應的結構平動時構件所承擔的剪力與結構轉動時構件所承擔的剪力，再根據力的平衡條件，推導出雙向地震作用下考慮構件抗扭剛度時結構的線彈性扭轉角，並對構件的剪力及變形進行了修正。分享友人